← Commit history
README.md+15−15
@@ -8,21 +8,21 @@ TDA7293V from STMicroelectronics, in a MultiwAtt-15. Pinout and pin descriptions  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | STAND-BY GND | power_in | Reference pin for the standby and mute thresholds, with standby-on and mute-on at or below 1.5 V and standby-off and mute-off at or above 3.5 V relative to this pin. |-| 2 | IN- | input | Inverting signal input with 100 kΩ typical input resistance; closed-loop gain is set by R2 = 680 Ω (about 30 dB), which must stay at or above 26 dB. |-| 3 | IN+ | input | Non-inverting signal input with 100 kΩ typical input resistance, with R1 (22 kΩ) and R3 (22 kΩ) set per the recommended application circuit. |-| 4 | SGND | power_in | Signal ground, referenced to -VS (pin 8) with a maximum of 90 V, and also the slave-function pin that must be tied to the negative supply in modular (parallel) operation, where slave is at or below 1 V and master is at or above 3 V relative to pin 8. |-| 5 | CLIP DET | output | Clip detector output with a duty cycle of about 30 to 50 % at d = 10 % (10 kΩ pull-up to 5 V) and leakage of 3 µA maximum at 50 W; its voltage is rated at 120 V referred to -VS. |-| 6 | BOOTSTRAP | passive | Bootstrap node, rated 120 V referred to -VS, where the bootstrap capacitor connects either to the output (pin 14) or to the bootstrap loader (pin 12). |-| 7 | -VS (SIGNAL) | power_in | Negative signal supply for the small-signal circuitry, to be bypassed with 100 nF per the application circuit. |-| 8 | -VS (POWER) | power_in | Negative power supply and device tab; all voltage ratings (for example standby, mute and input voltages) are referenced to this pin. |-| 9 | STAND-BY | input | CMOS-logic-compatible standby control, with standby-on at or below 1.5 V and standby-off at or above 3.5 V relative to pin 1, and a maximum applicable voltage equal to the operating supply voltage. |-| 10 | MUTE | input | CMOS-logic-compatible mute control, with mute-on at or below 1.5 V and mute-off at or above 3.5 V relative to pin 1, rated 120 V referred to -VS. |-| 11 | BUFFER DRIVER | output | Output of the internal unity-gain buffer, used only for modular connection, with a maximum external load of 1 MΩ / 10 pF and intended for test purposes only. |-| 12 | BOOTSTRAP LOADER | passive | Bootstrap loader pin rated 100 V referred to -VS, which follows the output up to 100 V and stays clamped at 100 V for higher output voltages. |-| 13 | +VS (POWER) | power_in | Positive power supply pin for the output stage, which is bootstrapped in high-efficiency operation; supply range is ±12 V to ±50 V with ±60 V absolute maximum (no signal). |-| 14 | OUT | output | Amplifier output, rated for up to 10 A peak output current, with a current limiter threshold of 6.5 A typical for VS ≤ ±40 V. |-| 15 | +VS (SIGNAL) | power_in | Positive signal supply for the small-signal circuitry, with supply range ±12 V to ±50 V and ±60 V absolute maximum (no signal). |+| 1 | STAND-BY GND | power_in | Stand-by ground; the stand-by and mute thresholds are referenced to this pin, and its voltage is limited to 90 V referred to -VS. |+| 2 | INVERTING INPUT | input | Inverting input; limited to 90 V referred to -VS and to ±30 V differential against the non-inverting input. |+| 3 | NON INVERTING INPUT | input | Non-inverting input; limited to 90 V referred to -VS, and in slave devices this input is connected to the negative supply. |+| 4 | SIGNAL GROUND | power_in | Signal ground, limited to 90 V referred to -VS; it also sets the slave/master function, where at or below -VS+1 V it selects slave and at or above -VS+3 V it selects master. |+| 5 | CLIP AND SHORT CIRCUIT DETECTOR | output | Clip and short-circuit detector output, limited to 120 V referred to -VS and used with a pull-up resistor (for example 10 kΩ to 5 V). |+| 6 | BOOTSTRAP | passive | Bootstrap capacitor connection (to OUT pin 14 or to bootstrap loader pin 12), limited to 120 V referred to -VS. |+| 7 | +VS (SIGNAL) | power_in | Positive supply for the signal part; supply range is ±12 V to ±50 V. |+| 8 | -VS (SIGNAL) | power_in | Negative supply for the signal part, the reference for the absolute maximum voltages, connected to the tab. |+| 9 | STAND-BY | input | Stand-by control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS. |+| 10 | MUTE | input | Mute control input, CMOS logic compatible, with on threshold of 1.5 V max and off threshold of 3.5 V min referred to pin 1, and limited to 120 V referred to -VS. |+| 11 | BUFFER DRIVER | bidirectional | Buffer driver pin used only for modular (parallel) connection of devices, limited to 120 V referred to -VS. |+| 12 | BOOTSTRAP LOADER | passive | Bootstrap loader that follows the output voltage up to 100 V and is clamped at 100 V above that, allowing a maximum supply voltage of 120 V when the bootstrap capacitor is connected to pin 6. |+| 13 | +VS (POWER) | power_in | Positive supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V. |+| 14 | OUT | output | Power amplifier output with 10 A peak output current limit and current limiter threshold of 6.5 A typ at VS up to ±40 V. |+| 15 | -VS (POWER) | power_in | Negative supply for the power stage, which can be bootstrapped in high-efficiency applications; supply range is ±12 V to ±50 V. |  ## Key specifications 
package.json+8−8
@@ -1,6 +1,6 @@ {   "slug": "tda7293v",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -76,13 +76,13 @@         "number": "2",         "name": "IN-",         "type": "input",-        "description": "Inverting signal input with 100 kΩ typical input resistance; closed-loop gain is set by R2 = 680 Ω (about 30 dB), which must stay at or above 26 dB."+        "description": "Inverting signal input with 100 k\u03a9 typical input resistance; closed-loop gain is set by R2 = 680 \u03a9 (about 30 dB), which must stay at or above 26 dB."       },       {         "number": "3",         "name": "IN+",         "type": "input",-        "description": "Non-inverting signal input with 100 kΩ typical input resistance, with R1 (22 kΩ) and R3 (22 kΩ) set per the recommended application circuit."+        "description": "Non-inverting signal input with 100 k\u03a9 typical input resistance, with R1 (22 k\u03a9) and R3 (22 k\u03a9) set per the recommended application circuit."       },       {         "number": "4",@@ -94,7 +94,7 @@         "number": "5",         "name": "CLIP DET",         "type": "output",-        "description": "Clip detector output with a duty cycle of about 30 to 50 % at d = 10 % (10 kΩ pull-up to 5 V) and leakage of 3 µA maximum at 50 W; its voltage is rated at 120 V referred to -VS."+        "description": "Clip detector output with a duty cycle of about 30 to 50 % at d = 10 % (10 k\u03a9 pull-up to 5 V) and leakage of 3 \u00b5A maximum at 50 W; its voltage is rated at 120 V referred to -VS."       },       {         "number": "6",@@ -130,7 +130,7 @@         "number": "11",         "name": "BUFFER DRIVER",         "type": "output",-        "description": "Output of the internal unity-gain buffer, used only for modular connection, with a maximum external load of 1 MΩ / 10 pF and intended for test purposes only."+        "description": "Output of the internal unity-gain buffer, used only for modular connection, with a maximum external load of 1 M\u03a9 / 10 pF and intended for test purposes only."       },       {         "number": "12",@@ -142,19 +142,19 @@         "number": "13",         "name": "+VS (POWER)",         "type": "power_in",-        "description": "Positive power supply pin for the output stage, which is bootstrapped in high-efficiency operation; supply range is ±12 V to ±50 V with ±60 V absolute maximum (no signal)."+        "description": "Positive power supply pin for the output stage, which is bootstrapped in high-efficiency operation; supply range is \u00b112 V to \u00b150 V with \u00b160 V absolute maximum (no signal)."       },       {         "number": "14",         "name": "OUT",         "type": "output",-        "description": "Amplifier output, rated for up to 10 A peak output current, with a current limiter threshold of 6.5 A typical for VS ≤ ±40 V."+        "description": "Amplifier output, rated for up to 10 A peak output current, with a current limiter threshold of 6.5 A typical for VS \u2264 \u00b140 V."       },       {         "number": "15",         "name": "+VS (SIGNAL)",         "type": "power_in",-        "description": "Positive signal supply for the small-signal circuitry, with supply range ±12 V to ±50 V and ±60 V absolute maximum (no signal)."+        "description": "Positive signal supply for the small-signal circuitry, with supply range \u00b112 V to \u00b150 V and \u00b160 V absolute maximum (no signal)."       }     ],     "provenance": {
page.json+4−4
@@ -4,7 +4,7 @@   "slug": "tda7293v",   "title": "TDA7293V",   "brief": "STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -744,7 +744,7 @@     "tda7293v-hero.overlay.json",     "tda7293v-etched.glb"   ],-  "visibility": {-    "public": true-  }+  "visibility": "public",+  "description": "STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
tda7293v-hero.glb
⋯ 1 unchanged line ⋯
tda7293v-hero.overlay.json+8−8
@@ -79,7 +79,7 @@     "footprint": "tda7293v.kicad_mod",     "footprint_sha256": "08ef00463c3cff6fa2920784f1573add2de6e182a56601281644050f6f5c2fb2",     "pins": "page.json component.pins",-    "pins_sha256": "631d37072ec5f2063eb78e77d49f357a74461c5742fc5bb577ff3214e4bc860b"+    "pins_sha256": "03f439cc8ed8f641ef4d19747c8b96b9bccd81ed9514cb1e027edc2810979b0f"   },   "generator": "adom-wiki 1.8.11 (component_hero)",   "labels": [@@ -94,7 +94,7 @@     },     {       "pad": "2",-      "text": "IN-",+      "text": "INVERTING INPUT",       "x": -7.62,       "y": -3.54,       "align": "left",@@ -103,7 +103,7 @@     },     {       "pad": "3",-      "text": "IN+",+      "text": "NON INVERTING INPUT",       "x": -6.35,       "y": 3.54,       "align": "right",@@ -112,7 +112,7 @@     },     {       "pad": "4",-      "text": "SGND",+      "text": "SIGNAL GROUND",       "x": -5.08,       "y": -3.54,       "align": "left",@@ -121,7 +121,7 @@     },     {       "pad": "5",-      "text": "CLIP DET",+      "text": "CLIP AND SHORT CIRCUIT DETECTOR",       "x": -3.81,       "y": 3.54,       "align": "right",@@ -139,7 +139,7 @@     },     {       "pad": "7",-      "text": "-VS (SIGNAL)",+      "text": "+VS (SIGNAL)",       "x": -1.27,       "y": 3.54,       "align": "right",@@ -148,7 +148,7 @@     },     {       "pad": "8",-      "text": "-VS (POWER)",+      "text": "-VS (SIGNAL)",       "x": 0.0,       "y": -3.54,       "align": "left",@@ -211,7 +211,7 @@     },     {       "pad": "15",-      "text": "+VS (SIGNAL)",+      "text": "-VS (POWER)",       "x": 9.89,       "y": 2.54,       "align": "left",
tda7293v.kicad_sym+23−23
@@ -4,67 +4,67 @@     (property "Value" "TDA7293V" (at 0 -15.24 0) (effects (font (size 1.27 1.27))))     (property "Footprint" "" (at 0 0 0) (effects (font (size 1.27 1.27)) hide))     (symbol "TDA7293V_0_1"-    (rectangle (start -17.78 10.16) (end 17.78 -12.70)+    (rectangle (start -27.94 10.16) (end 27.94 -12.70)       (stroke (width 0.254) (type default)) (fill (type background)))     )     (symbol "TDA7293V_1_1"-    (pin power_in line (at -22.86 7.62 0) (length 5.08)+    (pin power_in line (at -33.02 7.62 0) (length 5.08)       (name "STAND-BY GND" (effects (font (size 1.27 1.27))))       (number "1" (effects (font (size 1.27 1.27))))     )-    (pin input line (at -22.86 5.08 0) (length 5.08)-      (name "IN-" (effects (font (size 1.27 1.27))))+    (pin input line (at -33.02 5.08 0) (length 5.08)+      (name "INVERTING INPUT" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )-    (pin input line (at -22.86 2.54 0) (length 5.08)-      (name "IN+" (effects (font (size 1.27 1.27))))+    (pin input line (at -33.02 2.54 0) (length 5.08)+      (name "NON INVERTING INPUT" (effects (font (size 1.27 1.27))))       (number "3" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at -22.86 0.00 0) (length 5.08)-      (name "SGND" (effects (font (size 1.27 1.27))))+    (pin power_in line (at -33.02 0.00 0) (length 5.08)+      (name "SIGNAL GROUND" (effects (font (size 1.27 1.27))))       (number "4" (effects (font (size 1.27 1.27))))     )-    (pin output line (at -22.86 -2.54 0) (length 5.08)-      (name "CLIP DET" (effects (font (size 1.27 1.27))))+    (pin output line (at -33.02 -2.54 0) (length 5.08)+      (name "CLIP AND SHORT CIRCUIT DETECTOR" (effects (font (size 1.27 1.27))))       (number "5" (effects (font (size 1.27 1.27))))     )-    (pin passive line (at -22.86 -5.08 0) (length 5.08)+    (pin passive line (at -33.02 -5.08 0) (length 5.08)       (name "BOOTSTRAP" (effects (font (size 1.27 1.27))))       (number "6" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at -22.86 -7.62 0) (length 5.08)-      (name "-VS (SIGNAL)" (effects (font (size 1.27 1.27))))+    (pin power_in line (at -33.02 -7.62 0) (length 5.08)+      (name "+VS (SIGNAL)" (effects (font (size 1.27 1.27))))       (number "7" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at -22.86 -10.16 0) (length 5.08)-      (name "-VS (POWER)" (effects (font (size 1.27 1.27))))+    (pin power_in line (at -33.02 -10.16 0) (length 5.08)+      (name "-VS (SIGNAL)" (effects (font (size 1.27 1.27))))       (number "8" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at 22.86 7.62 180) (length 5.08)-      (name "+VS (SIGNAL)" (effects (font (size 1.27 1.27))))+    (pin power_in line (at 33.02 7.62 180) (length 5.08)+      (name "-VS (POWER)" (effects (font (size 1.27 1.27))))       (number "15" (effects (font (size 1.27 1.27))))     )-    (pin output line (at 22.86 5.08 180) (length 5.08)+    (pin output line (at 33.02 5.08 180) (length 5.08)       (name "OUT" (effects (font (size 1.27 1.27))))       (number "14" (effects (font (size 1.27 1.27))))     )-    (pin power_in line (at 22.86 2.54 180) (length 5.08)+    (pin power_in line (at 33.02 2.54 180) (length 5.08)       (name "+VS (POWER)" (effects (font (size 1.27 1.27))))       (number "13" (effects (font (size 1.27 1.27))))     )-    (pin passive line (at 22.86 0.00 180) (length 5.08)+    (pin passive line (at 33.02 0.00 180) (length 5.08)       (name "BOOTSTRAP LOADER" (effects (font (size 1.27 1.27))))       (number "12" (effects (font (size 1.27 1.27))))     )-    (pin output line (at 22.86 -2.54 180) (length 5.08)+    (pin bidirectional line (at 33.02 -2.54 180) (length 5.08)       (name "BUFFER DRIVER" (effects (font (size 1.27 1.27))))       (number "11" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 22.86 -5.08 180) (length 5.08)+    (pin input line (at 33.02 -5.08 180) (length 5.08)       (name "MUTE" (effects (font (size 1.27 1.27))))       (number "10" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 22.86 -7.62 180) (length 5.08)+    (pin input line (at 33.02 -7.62 180) (length 5.08)       (name "STAND-BY" (effects (font (size 1.27 1.27))))       (number "9" (effects (font (size 1.27 1.27))))     )
tda7293v.lbr+40−29
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet</description> <packages> <package name="STMicroelectronics_TDA7293">   <description>15 pads, 19.5 x 6.8 mm. Generated from the STMicroelectronics datasheet land pattern (family R1387, spec 1f8cb35e95)</description>@@ -80,32 +80,33 @@ </packages> <symbols> <symbol name="TDA7293V">-  <wire x1="-17.78" y1="10.16" x2="17.78" y2="10.16" width="0.254" layer="94"/>-  <wire x1="17.78" y1="10.16" x2="17.78" y2="-12.7" width="0.254" layer="94"/>-  <wire x1="17.78" y1="-12.7" x2="-17.78" y2="-12.7" width="0.254" layer="94"/>-  <wire x1="-17.78" y1="-12.7" x2="-17.78" y2="10.16" width="0.254" layer="94"/>+  <description>STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet</description>+  <wire x1="-27.94" y1="10.16" x2="27.94" y2="10.16" width="0.254" layer="94"/>+  <wire x1="27.94" y1="10.16" x2="27.94" y2="-12.7" width="0.254" layer="94"/>+  <wire x1="27.94" y1="-12.7" x2="-27.94" y2="-12.7" width="0.254" layer="94"/>+  <wire x1="-27.94" y1="-12.7" x2="-27.94" y2="10.16" width="0.254" layer="94"/>   <text x="0.0000" y="12.7000" size="1.27" layer="95" align="center">&gt;NAME</text>   <text x="0.0000" y="-15.2400" size="1.27" layer="96" align="center">&gt;VALUE</text>-  <pin name="STAND-BY_GND" x="-22.86" y="7.62" length="middle" direction="pwr"/>-  <pin name="IN-" x="-22.86" y="5.08" length="middle" direction="in"/>-  <pin name="IN+" x="-22.86" y="2.54" length="middle" direction="in"/>-  <pin name="SGND" x="-22.86" y="0" length="middle" direction="pwr"/>-  <pin name="CLIP_DET" x="-22.86" y="-2.54" length="middle" direction="out"/>-  <pin name="BOOTSTRAP" x="-22.86" y="-5.08" length="middle" direction="pas"/>-  <pin name="-VS_SIGNAL" x="-22.86" y="-7.62" length="middle" direction="pwr"/>-  <pin name="-VS_POWER" x="-22.86" y="-10.16" length="middle" direction="pwr"/>-  <pin name="+VS_SIGNAL" x="22.86" y="7.62" length="middle" direction="pwr" rot="R180"/>-  <pin name="OUT" x="22.86" y="5.08" length="middle" direction="out" rot="R180"/>-  <pin name="+VS_POWER" x="22.86" y="2.54" length="middle" direction="pwr" rot="R180"/>-  <pin name="BOOTSTRAP_LOADER" x="22.86" y="0" length="middle" direction="pas" rot="R180"/>-  <pin name="BUFFER_DRIVER" x="22.86" y="-2.54" length="middle" direction="out" rot="R180"/>-  <pin name="MUTE" x="22.86" y="-5.08" length="middle" direction="in" rot="R180"/>-  <pin name="STAND-BY" x="22.86" y="-7.62" length="middle" direction="in" rot="R180"/>+  <pin name="STAND-BY_GND" x="-33.02" y="7.62" length="middle" direction="pwr"/>+  <pin name="INVERTING_INPUT" x="-33.02" y="5.08" length="middle" direction="in"/>+  <pin name="NON_INVERTING_INPUT" x="-33.02" y="2.54" length="middle" direction="in"/>+  <pin name="SIGNAL_GROUND" x="-33.02" y="0" length="middle" direction="pwr"/>+  <pin name="CLIP_AND_SHORT_CIRCUIT_DETECTOR" x="-33.02" y="-2.54" length="middle" direction="out"/>+  <pin name="BOOTSTRAP" x="-33.02" y="-5.08" length="middle" direction="pas"/>+  <pin name="+VS_SIGNAL" x="-33.02" y="-7.62" length="middle" direction="pwr"/>+  <pin name="-VS_SIGNAL" x="-33.02" y="-10.16" length="middle" direction="pwr"/>+  <pin name="-VS_POWER" x="33.02" y="7.62" length="middle" direction="pwr" rot="R180"/>+  <pin name="OUT" x="33.02" y="5.08" length="middle" direction="out" rot="R180"/>+  <pin name="+VS_POWER" x="33.02" y="2.54" length="middle" direction="pwr" rot="R180"/>+  <pin name="BOOTSTRAP_LOADER" x="33.02" y="0" length="middle" direction="pas" rot="R180"/>+  <pin name="BUFFER_DRIVER" x="33.02" y="-2.54" length="middle" direction="io" rot="R180"/>+  <pin name="MUTE" x="33.02" y="-5.08" length="middle" direction="in" rot="R180"/>+  <pin name="STAND-BY" x="33.02" y="-7.62" length="middle" direction="in" rot="R180"/> </symbol> </symbols> <devicesets> <deviceset name="TDA7293V" prefix="U">-  <description></description>+  <description>STMicroelectronics Audio Amplifiers, MultiwAtt-15. Pinout reviewed by a person against the datasheet</description>   <gates>     <gate name="G$1" symbol="TDA7293V" x="0" y="0"/>   </gates>@@ -113,14 +114,14 @@     <device name="" package="STMicroelectronics_TDA7293">       <connects>         <connect gate="G$1" pin="STAND-BY_GND" pad="1"/>-        <connect gate="G$1" pin="IN-" pad="2"/>-        <connect gate="G$1" pin="IN+" pad="3"/>-        <connect gate="G$1" pin="SGND" pad="4"/>-        <connect gate="G$1" pin="CLIP_DET" pad="5"/>+        <connect gate="G$1" pin="INVERTING_INPUT" pad="2"/>+        <connect gate="G$1" pin="NON_INVERTING_INPUT" pad="3"/>+        <connect gate="G$1" pin="SIGNAL_GROUND" pad="4"/>+        <connect gate="G$1" pin="CLIP_AND_SHORT_CIRCUIT_DETECTOR" pad="5"/>         <connect gate="G$1" pin="BOOTSTRAP" pad="6"/>-        <connect gate="G$1" pin="-VS_SIGNAL" pad="7"/>-        <connect gate="G$1" pin="-VS_POWER" pad="8"/>-        <connect gate="G$1" pin="+VS_SIGNAL" pad="15"/>+        <connect gate="G$1" pin="+VS_SIGNAL" pad="7"/>+        <connect gate="G$1" pin="-VS_SIGNAL" pad="8"/>+        <connect gate="G$1" pin="-VS_POWER" pad="15"/>         <connect gate="G$1" pin="OUT" pad="14"/>         <connect gate="G$1" pin="+VS_POWER" pad="13"/>         <connect gate="G$1" pin="BOOTSTRAP_LOADER" pad="12"/>@@ -128,7 +129,17 @@         <connect gate="G$1" pin="MUTE" pad="10"/>         <connect gate="G$1" pin="STAND-BY" pad="9"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="TDA7293V" constant="no"/>+          <attribute name="MANUFACTURER" value="STMicroelectronics" constant="no"/>+          <attribute name="DATASHEET" value="https://www.st.com/resource/en/datasheet/tda7293v.pdf" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/tda7293v" constant="no"/>+          <attribute name="MOUSER_PN" value="511-TDA7293V" constant="no"/>+          <attribute name="DIGIKEY_PN" value="497-2170-5-ND" constant="no"/>+          <attribute name="LCSC_PN" value="C96008" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>