← Commit history

td1837: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·d388695f76 · ·parent df5ffd9
1 file changed +81−1
page.json+81−1
@@ -33,5 +33,85 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "TD1837",+    "manufacturer": "Techcode Semicon",+    "package": "ESOP-8",+    "pin_count": 9,+    "category": "DC-DC Converters",+    "parts": {+      "symbol": "td1837.kicad_sym",+      "footprint": "td1837.kicad_mod",+      "model_3d": "td1837-etched.glb",+      "model_3d_plain": "td1837.glb",+      "model_3d_step": "td1837-etched.step",+      "model_3d_step_plain": "td1837.step",+      "lbr": "td1837.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "SW",+        "type": "output",+        "description": "Switch Node. Output from the internal high-side power MOSFET (250mΩ RDS(on)). Requires an external low-VF Schottky rectifier to ground placed close to the pin to reduce switching spikes. Switch voltage range -0.5V to VIN+0.5V."+      },+      {+        "number": "2",+        "name": "EN",+        "type": "input",+        "description": "Enable Input (positive logic). Pulling below the falling threshold (~1.7V) or leaving floating shuts the chip down; pulling above the rising threshold (~1.9V, spec 1.3V min to 2.2V max) enables the chip. Internal ~1MΩ pull-down to GND."+      },+      {+        "number": "3",+        "name": "COMP",+        "type": "output",+        "description": "Compensation. Output of the internal GM error amplifier. Connect an external R-C compensation network here to set loop dynamics. Internally clamped between ~0.9V (min) and ~2.0V (max) during operation; do not drive above 2.6V."+      },+      {+        "number": "4",+        "name": "FB",+        "type": "input",+        "description": "Feedback. Inverting input to the internal error amplifier. An external resistive divider from VOUT to GND sets the output voltage; the divider is compared to the internal 0.8V reference (VFB = 0.780V to 0.820V)."+      },+      {+        "number": "5",+        "name": "GND",+        "type": "power_in",+        "description": "Ground. Common return for the device and shared with the exposed thermal pad. Connect as close as possible to the output capacitor while avoiding high-current switch paths. The exposed pad must be tied to the GND plane for optimal thermal performance."+      },+      {+        "number": "6",+        "name": "FREQ",+        "type": "input",+        "description": "Switching Frequency Program Input. Connect a resistor RFREQ from this pin to ground to program the oscillator frequency (up to 1MHz). RFREQ(kΩ) = 100000/fs(kHz) − 5. For VIN ≥ 64V, set fsw below 400kHz."+      },+      {+        "number": "7",+        "name": "VIN",+        "type": "power_in",+        "description": "Input Supply. Supplies all internal control circuitry, bootstrap regulators, and the high-side power MOSFET. Absolute maximum 80V (operating range 12V to 80V; VIN UVLO ~7.2V rising, ~6.5V falling). A decoupling capacitor to ground must be placed close to this pin."+      },+      {+        "number": "8",+        "name": "BST",+        "type": "power_in",+        "description": "Bootstrap. Positive supply for the internal floating high-side MOSFET gate driver. Connect a bypass capacitor (typ. 0.1μF) between BST and SW. Internally regulated to ~5V above SW; BST-to-SW absolute maximum is +5V."+      },+      {+        "number": "EP",+        "name": "GND",+        "type": "power_in",+        "description": "Exposed thermal pad on the bottom of the ESOP-8 package. Electrically tied to GND (pin 5). Solder to a large GND copper area for optimal thermal performance.",+        "thermal_pad": true+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}