main
Ray
Publish 0.3.0
b6c3e83
TD1468
Techcode Semicon · DC-DC Converters · ESOP-8
TD1468 from Techcode Semicon, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Bootstrap. Connect a capacitor between SW and BST pins to form a floating supply across the power switch driver. This capacitor drives the internal N-channel power MOSFET gate above the supply voltage. Absolute max: VSW - 0.3V to VSW + 6V. |
| 2 | VIN | power_in | Supply voltage input. Operates from a 10V-to-60V unregulated input (recommended 11V-60V). Requires an input bypass capacitor (e.g. 1μF ceramic plus bulk) to prevent large voltage spikes. Absolute max 60V. |
| 3 | EN | input | Enable / on-off control. Pull EN above 1.35V (typ) to turn the device ON; falling threshold 1.17V, ~180mV hysteresis. For automatic enable, connect to VIN through a 1MΩ resistor. Absolute max 6V. |
| 4 | NC | unconnected | No internal connection. Leave floating or tie to ground per PCB layout preference. |
| 5 | FB | input | Feedback input. Sets output voltage via an external resistor divider from VOUT to GND; internal reference is 0.812V (typ, 0.792-0.832V). A frequency foldback comparator lowers the oscillator frequency to ~120kHz when FB is below 300mV to prevent current-limit runaway during short-circuit faults. |
| 6 | NC | unconnected | No internal connection. Leave floating or tie to ground per PCB layout preference. |
| 7 | GND | power_in | Ground / voltage reference for the regulated output. Requires careful layout - isolate from the freewheeling diode (D1) to input-cap (C1) ground path to prevent switching current spikes from inducing noise into the reference. |
| 8 | SW | output | Power switching output. Drain of the internal N-channel power MOSFET (RDS(on) ~0.7Ω); connects to the external inductor and Schottky freewheeling diode of the LC output filter. Current limit ~2.8A typ. Absolute max -0.3V to VIN+0.3V. |
| 9 | EP | passive | Exposed pad; net not stated. The pin table lists pins 1-8 only; the sheet's one mention is the layout tip on p.6: "For single layer PCBs, avoid soldering the exposed pad." KiCad's SOIC-8-1EP numbers it 9. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Techcode Semicon |
| Package | ESOP-8 |
| Category | PMIC |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage | VFB | 0.792 | 0.812 | 0.832 | V | 10V ≤ VIN ≤ 60V | 4 |
| Feedback Current | IFB | 0.1 | µA | VFB = 0.85V | 4 | ||
| Switch Leakage | ISW_LKG | 1 | µA | VEN=0V,VSW=0V | 4 | ||
| Oscillator Frequency | fSW | 380 | 480 | 580 | kHZ | VFB=0.6V | 4 |
| Under-Voltage Lockout Threshold, Rising | VUVLO_R | 7.5 | 8.5 | V | Rising | 4 | |
| Supply Current (Shutdown) | IS | 0.1 | 1 | µA | VEN=0V | 4 | |
| Supply Current (Quiescent) | IQ | 0.73 | 0.85 | mA | VEN=2V,VFB=1V | 4 | |
| Operating Junction Temperature | TJ | -40 | 125 | °C | 4 | ||
| VIN Supply Voltage | VIN | 11 | 60 | V | Operating input range | 4 | |
| VIN Supply Voltage (VIN to Gnd) | VIN | -0.3 | 60 | V | VIN to GND | 3 | |
| SW to GND Voltage | VSW | -0.3 | 0.3 | V | Relative to VIN: -0.3 to VIN+0.3 V as printed | 3 | |
| BS to GND Voltage | VBS | -0.3 | 6 | V | Relative to VSW: VSW-0.3 to VSW+6 V as printed | 3 | |
| All Other Pins Voltage | -0.3 | 6 | V | All other pins | 3 | ||
| Junction Temperature | TJ | 150 | ºC | 3 | |||
| Storage Temperature | TSTG | -65 | 150 | ºC | 3 | ||
| Maximum Lead Soldering Temperature | TSDR | 260 | ºC | 10 seconds | 3 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 50 | °C/W | Free air, high effective thermal conductivity test board (Note 2) | 3 |
CAD (KiCad official)
- Symbol:
TD1468 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
td1468-etched.step/td1468-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);td1468.step/td1468.glbare the bare package body.
Provenance
No distributor stocks TD1468 yet. This page was built from the datasheet.
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Techcode Semicon datasheet (8 pp, sha256
2282f29b783eacae, retrieved 2026-11-16, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# TD1468
**Techcode Semicon** · DC-DC Converters · ESOP-8
TD1468 from Techcode Semicon, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Bootstrap. Connect a capacitor between SW and BST pins to form a floating supply across the power switch driver. This capacitor drives the internal N-channel power MOSFET gate above the supply voltage. Absolute max: VSW - 0.3V to VSW + 6V. |
| 2 | VIN | power_in | Supply voltage input. Operates from a 10V-to-60V unregulated input (recommended 11V-60V). Requires an input bypass capacitor (e.g. 1μF ceramic plus bulk) to prevent large voltage spikes. Absolute max 60V. |
| 3 | EN | input | Enable / on-off control. Pull EN above 1.35V (typ) to turn the device ON; falling threshold 1.17V, ~180mV hysteresis. For automatic enable, connect to VIN through a 1MΩ resistor. Absolute max 6V. |
| 4 | NC | unconnected | No internal connection. Leave floating or tie to ground per PCB layout preference. |
| 5 | FB | input | Feedback input. Sets output voltage via an external resistor divider from VOUT to GND; internal reference is 0.812V (typ, 0.792-0.832V). A frequency foldback comparator lowers the oscillator frequency to ~120kHz when FB is below 300mV to prevent current-limit runaway during short-circuit faults. |
| 6 | NC | unconnected | No internal connection. Leave floating or tie to ground per PCB layout preference. |
| 7 | GND | power_in | Ground / voltage reference for the regulated output. Requires careful layout - isolate from the freewheeling diode (D1) to input-cap (C1) ground path to prevent switching current spikes from inducing noise into the reference. |
| 8 | SW | output | Power switching output. Drain of the internal N-channel power MOSFET (RDS(on) ~0.7Ω); connects to the external inductor and Schottky freewheeling diode of the LC output filter. Current limit ~2.8A typ. Absolute max -0.3V to VIN+0.3V. |
| 9 | EP | passive | Exposed pad; net not stated. The pin table lists pins 1-8 only; the sheet's one mention is the layout tip on p.6: "For single layer PCBs, avoid soldering the exposed pad." KiCad's SOIC-8-1EP numbers it 9. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Techcode Semicon |
| Package | ESOP-8 |
| Category | PMIC |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Feedback Voltage | VFB | 0.792 | 0.812 | 0.832 | V | 10V ≤ VIN ≤ 60V | 4 |
| Feedback Current | IFB | | | 0.1 | µA | VFB = 0.85V | 4 |
| Switch Leakage | ISW_LKG | | | 1 | µA | VEN=0V,VSW=0V | 4 |
| Oscillator Frequency | fSW | 380 | 480 | 580 | kHZ | VFB=0.6V | 4 |
| Under-Voltage Lockout Threshold, Rising | VUVLO_R | | 7.5 | 8.5 | V | Rising | 4 |
| Supply Current (Shutdown) | IS | | 0.1 | 1 | µA | VEN=0V | 4 |
| Supply Current (Quiescent) | IQ | | 0.73 | 0.85 | mA | VEN=2V,VFB=1V | 4 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 4 |
| VIN Supply Voltage | VIN | 11 | | 60 | V | Operating input range | 4 |
| VIN Supply Voltage (VIN to Gnd) | VIN | -0.3 | | 60 | V | VIN to GND | 3 |
| SW to GND Voltage | VSW | -0.3 | | 0.3 | V | Relative to VIN: -0.3 to VIN+0.3 V as printed | 3 |
| BS to GND Voltage | VBS | -0.3 | | 6 | V | Relative to VSW: VSW-0.3 to VSW+6 V as printed | 3 |
| All Other Pins Voltage | | -0.3 | | 6 | V | All other pins | 3 |
| Junction Temperature | TJ | | | 150 | ºC | | 3 |
| Storage Temperature | TSTG | -65 | | 150 | ºC | | 3 |
| Maximum Lead Soldering Temperature | TSDR | | | 260 | ºC | 10 seconds | 3 |
| Junction-to-Ambient Thermal Resistance | θJA | | 50 | | °C/W | Free air, high effective thermal conductivity test board (Note 2) | 3 |
## CAD (KiCad official)
- Symbol: `TD1468`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `td1468-etched.step` / `td1468-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `td1468.step` / `td1468.glb` are the bare package body.
## Provenance
> No distributor stocks TD1468 yet. This page was built from the datasheet.
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Techcode Semicon datasheet]() (8 pp, sha256 `2282f29b783eacae`, retrieved 2026-11-16, tier: manufacturer)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/td1468-datasheet.pdf)