3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownTC4431CPA
Microchip Tech · Gate Drive ICs · PDIP-8
TC4431CPA from Microchip Tech, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Bias supply input for the MOSFET driver, rated for 4.5V to 30V with respect to the ground pins and should be bypassed to ground with a local ceramic capacitor. |
| 2 | IN | input | TTL/CMOS compatible control input with 250 mV of hysteresis between the high and low thresholds, where a series current-limiting resistor is recommended if the input exceeds 12V. |
| 3 | LOCK DIS | input | Enables or disables undervoltage lockout: leave floating for lockout (output enabled at 8.4V typical rising, disabled at 7.7V typical falling) or tie to ground for operation below 7V. |
| 4 | GND | power_in | Ground return path for the bias current and high peak discharge currents, and both ground pins should be used for proper operation. |
| 5 | GND | power_in | Ground return path for the bias current and high peak discharge currents, and both ground pins should be used for proper operation. |
| 6 | OUT | output | Sink (pull-down) drive output that can sink 1.5 A peak currents from a capacitive load. |
| 7 | OUT | output | Source (pull-up) drive output that can source 3 A peak currents into capacitive loads. |
| 8 | VDD | power_in | Bias supply input for the MOSFET driver, rated for 4.5V to 30V with respect to the ground pins and should be bypassed to ground with a local ceramic capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | PDIP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic '1' High Input Voltage | VIH | 2.4 | V | 3 | |||
| Logic '0' Low Input Voltage | VIL | 0.8 | V | 3 | |||
| Input Current | IIN | -1 | 1 | µA | 0V ≤ VIN ≤ 12V | 3 | |
| Low Output Voltage | VOL | 0.025 | V | 3 | |||
| Output Resistance | RO | 7 | 10 | Ω | IOUT = 10 mA, VDD = 30V | 3 | |
| Peak Output Current Source | IPK | 3 | A | Source: VDD = 30V | 3 | ||
| Peak Output Current Sink | IPK | 1.5 | A | Sink: VDD = 30V | 3 | ||
| Rise Time | tR | 25 | 40 | ns | Figure 4-1 | 3 | |
| Fall Time | tF | 33 | 50 | ns | Figure 4-1 | 3 | |
| Delay Time tD1 | tD1 | 62 | 80 | ns | Figure 4-1 | 3 | |
| Delay Time tD2 | tD2 | 78 | 90 | ns | Figure 4-1 | 3 | |
| Power Supply Current | IS | 2.5 | 4 | mA | VIN = 3V | 3 | |
| Power Supply Current | IS | 0.3 | 0.4 | mA | VIN = 0V | 3 | |
| Start-up Threshold | VS | 8.4 | 10 | V | 3 | ||
| Drop-out Threshold | VDO | 7 | 7.7 | V | Note 3 | 3 | |
| Latch-Up Protection Withstand Reverse Current | IREV | 0.3 | A | Duty cycle ≤ 2%, t ≤ 300 µsec | 3 | ||
| Logic '1' High Input Voltage (over temperature) | VIH | 2.4 | V | 4 | |||
| Logic '0' Low Input Voltage (over temperature) | VIL | 0.8 | V | 4 | |||
| Input Current (over temperature) | IIN | -10 | 10 | µA | 0V ≤ VIN ≤ 12V | 4 | |
| Low Output Voltage (over temperature) | VOL | 0.025 | V | 4 | |||
| Output Resistance (over temperature) | RO | 12 | Ω | IOUT = 10 mA, VDD = 30V | 4 | ||
| Rise Time (over temperature) | tR | 60 | ns | Figure 4-1 | 4 | ||
| Fall Time (over temperature) | tF | 70 | ns | Figure 4-1 | 4 | ||
| Delay Time tD1 (over temperature) | tD1 | 100 | ns | Figure 4-1 | 4 | ||
| Delay Time tD2 (over temperature) | tD2 | 110 | ns | Figure 4-1 | 4 | ||
| Power Supply Current (over temperature) | IS | 6 | mA | VIN = 3V | 4 | ||
| Power Supply Current (over temperature) | IS | 0.7 | mA | VIN = 0V | 4 | ||
| Start-up Threshold (over temperature) | VS | 8.4 | 10 | V | 4 | ||
| Drop-out Threshold (over temperature) | VDO | 7 | 7.7 | V | Note 3 | 4 | |
| Supply Voltage (VDD) | VDD | 4.5 | 30 | V | 3 | ||
| Specified Temperature Range (C) | TA | 0 | 70 | ºC | 4 | ||
| Maximum Junction Temperature | TJ | 150 | ºC | 3 | |||
| Storage Temperature Range | TA | -65 | 150 | ºC | 3 | ||
| Thermal Resistance, 8L-PDIP | θJA | 125 | ºC/W | 4 |
CAD (KiCad official)
- Symbol:
TC4431CPA - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: PDIP-8 (KiCad packages3D, STEP)
- 3D model files:
tc4431cpa-etched.step/tc4431cpa-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tc4431cpa.step/tc4431cpa.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (18 pp, sha256
2a6e62628b47c4fb, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).