← Commit history

Initial commit: component/tas5731mphpr

Ray ·969b7d75fb ·
2 files changed +492
README.mdadded+86
@@ -0,0 +1,86 @@+# TAS5731MPHPR++**Texas Instruments** · Audio Amplifiers · TQFP-48-EP(7x7)++TAS5731MPHPR from Texas Instruments, in a TQFP-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OUT_A | output | Half-bridge A PWM audio output pin. |+| 2 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |+| 3 | PVDD_AB | power_in | Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |+| 4 | BST_A | power_in | High-side bootstrap supply for half-bridge A gate driver; connect 10-nF ceramic capacitor to OUT_A. |+| 5 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 6 | SSTIMER | passive | Soft-start ramp time control; leave floating for BD mode or connect 2.2-nF capacitor to ground for AD mode. |+| 7 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 8 | PBTL | input | Mode select input with internal pulldown; logic low selects BTL mode (default), logic high selects PBTL mode. |+| 9 | AVSS | power_in | Analog 3.3-V supply ground connection. |+| 10 | PLL_FLTM | output | PLL negative loop-filter terminal; connect to external RC network with 47-nF and 4.7-nF capacitors and 470-Ω resistor. |+| 11 | PLL_FLTP | output | PLL positive loop-filter terminal; connect to external RC network as specified for PLL_FLTM. |+| 12 | VR_ANA | power_out | Internally regulated 1.8-V analog supply; must not be used to power external devices. |+| 13 | AVDD | power_in | 3.3-V analog power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |+| 14 | ADR/FAULT | bidirectional | Dual-function pin: sets I2C address to 0x36 if pulled high, 0x34 if pulled low; can be configured as active-low fault output. |+| 15 | MCLK | input | Master clock input (2.8224 to 24.576-MHz) with 5-V tolerance, 40-60% duty cycle, and 5-ns maximum rise/fall time. |+| 16 | OSC_RES | output | Oscillator trim resistor connection; connect 18.2-kΩ 1% resistor to DVSSO for oscillator frequency calibration. |+| 17 | DVSSO | power_in | Oscillator ground; oscillator trim resistor connects from OSC_RES to this pin. |+| 18 | VR_DIG | power_out | Internally regulated 1.8-V digital supply; must not be used to power external devices. |+| 19 | PDN | input | Active-low power-down input with internal pullup; initiates PWM stop sequence and noise shaper shutdown. |+| 20 | LRCLK | input | I2S left/right clock (sample-rate clock) input with 5-V tolerance; supports 8 to 48-kHz sample rates. |+| 21 | SCLK | input | I2S serial bit clock input (1.024 to 12.288-MHz at 32×, 48×, or 64×fS) with 5-V tolerance and 8-ns rise/fall time. |+| 22 | SDIN | input | Serial audio data input supporting 16-bit, 20-bit, and 24-bit I2S, left-justified, and right-justified data formats. |+| 23 | SDA | bidirectional | I2C open-drain serial data line with internal pullup; requires external 4.7-kΩ pullup resistor to DVDD. |+| 24 | SCL | input | I2C serial control clock input supporting 100-kHz and 400-kHz operation with 5-V tolerance. |+| 25 | RESET | input | Active-low asynchronous reset input with internal pullup; must be held low for 100-µs minimum at power-up. |+| 26 | STEST | input | Factory test pin; must be connected directly to DVSS for proper operation. |+| 27 | DVDD | power_in | 3.3-V digital power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin. |+| 28 | DVSS | power_in | Digital ground connection. |+| 29 | GND | power_in | Analog ground for power stage; should be connected to system ground. |+| 30 | AGND | power_in | Local analog ground for power-stage output section; provides ground reference for output pins. |+| 31 | VREG | power_out | Digital regulator output; not to be used for powering external circuitry. |+| 32 | GVDD_OUT | power_out | Gate-drive regulator output derived from PVDD; supplies bootstrap charging diode for high-side gate drivers. |+| 33 | BST_D | power_in | High-side bootstrap supply for half-bridge D gate driver; connect 10-nF ceramic capacitor to OUT_D. |+| 34 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |+| 35 | PVDD_CD | power_in | Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin. |+| 36 | OUT_D | output | Half-bridge D PWM output pin for audio power amplification. |+| 37 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |+| 38 | PGND_CD | power_in | Power-stage ground for half-bridges C and D. |+| 39 | OUT_C | output | Half-bridge C PWM output pin for audio power amplification. |+| 40 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 41 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 42 | BST_C | power_in | High-side bootstrap supply for half-bridge C gate driver; connect 10-nF ceramic capacitor to OUT_C. |+| 43 | BST_B | power_in | High-side bootstrap supply for half-bridge B gate driver; connect 10-nF ceramic capacitor to OUT_B. |+| 44 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 45 | NC | unconnected | No internal connection; may be left floating or connected to ground. |+| 46 | OUT_B | output | Half-bridge B PWM output pin for audio power amplification. |+| 47 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |+| 48 | PGND_AB | power_in | Power-stage ground for half-bridges A and B. |+| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TQFP-48-EP(7x7) |+| Category | Amplifiers/Comparators |+| Pins | 49 |++## CAD (KiCad official)++- Symbol: `TAS5731MPHPR`+- Footprint: `Package_QFP:TQFP-48-1EP_7x7mm_P0.5mm_EP5x5mm`+- 3D model: TQFP-48-EP(7x7) (KiCad packages3D, STEP)+- 3D model files: `tas5731mphpr-etched.step` / `tas5731mphpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tas5731mphpr.step` / `tas5731mphpr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tas5731m) (71 pp, sha256 `b548f5b31dc8dd9b`, retrieved 2026-09-26, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tas5731mphpr-datasheet.pdf)
page.jsonadded+406
@@ -0,0 +1,406 @@+{+  "slug": "tas5731mphpr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Audio Amplifiers, TQFP-48-EP(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "amplifiers-comparators",+    "tas5731mphpr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tas5731mphpr.kicad_sym",+    "tas5731mphpr.kicad_mod",+    "tas5731mphpr.glb",+    "tas5731mphpr.step",+    "tas5731mphpr.lbr",+    "docs/hero.png",+    "docs/tas5731mphpr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TAS5731MPHPR",+    "manufacturer": "Texas Instruments",+    "package": "TQFP-48-EP(7x7)",+    "pin_count": 49,+    "category": "Amplifiers/Comparators",+    "subcategory": "Audio Amplifiers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tas5731m",+    "parts": {+      "symbol": "tas5731mphpr.kicad_sym",+      "footprint": "tas5731mphpr.kicad_mod",+      "model_3d": "tas5731mphpr-etched.glb",+      "model_3d_plain": "tas5731mphpr.glb",+      "model_3d_step": "tas5731mphpr-etched.step",+      "model_3d_step_plain": "tas5731mphpr.step",+      "lbr": "tas5731mphpr.lbr"+    },+    "distributor_links": {+      "lcsc": "C181751",+      "digikey": "296-40563-2-ND",+      "mouser": "595-TAS5731MPHPR"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T22:12:31Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-40563-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-TAS5731MPHPR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "OUT_A",+        "type": "output",+        "description": "Half-bridge A PWM audio output pin."+      },+      {+        "number": "2",+        "name": "PVDD_AB",+        "type": "power_in",+        "description": "Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin."+      },+      {+        "number": "3",+        "name": "PVDD_AB",+        "type": "power_in",+        "description": "Power-supply input for half-bridges A and B (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin."+      },+      {+        "number": "4",+        "name": "BST_A",+        "type": "power_in",+        "description": "High-side bootstrap supply for half-bridge A gate driver; connect 10-nF ceramic capacitor to OUT_A."+      },+      {+        "number": "5",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "6",+        "name": "SSTIMER",+        "type": "passive",+        "description": "Soft-start ramp time control; leave floating for BD mode or connect 2.2-nF capacitor to ground for AD mode."+      },+      {+        "number": "7",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "8",+        "name": "PBTL",+        "type": "input",+        "description": "Mode select input with internal pulldown; logic low selects BTL mode (default), logic high selects PBTL mode."+      },+      {+        "number": "9",+        "name": "AVSS",+        "type": "power_in",+        "description": "Analog 3.3-V supply ground connection."+      },+      {+        "number": "10",+        "name": "PLL_FLTM",+        "type": "output",+        "description": "PLL negative loop-filter terminal; connect to external RC network with 47-nF and 4.7-nF capacitors and 470-Ω resistor."+      },+      {+        "number": "11",+        "name": "PLL_FLTP",+        "type": "output",+        "description": "PLL positive loop-filter terminal; connect to external RC network as specified for PLL_FLTM."+      },+      {+        "number": "12",+        "name": "VR_ANA",+        "type": "power_out",+        "description": "Internally regulated 1.8-V analog supply; must not be used to power external devices."+      },+      {+        "number": "13",+        "name": "AVDD",+        "type": "power_in",+        "description": "3.3-V analog power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin."+      },+      {+        "number": "14",+        "name": "ADR/FAULT",+        "type": "bidirectional",+        "description": "Dual-function pin: sets I2C address to 0x36 if pulled high, 0x34 if pulled low; can be configured as active-low fault output."+      },+      {+        "number": "15",+        "name": "MCLK",+        "type": "input",+        "description": "Master clock input (2.8224 to 24.576-MHz) with 5-V tolerance, 40-60% duty cycle, and 5-ns maximum rise/fall time."+      },+      {+        "number": "16",+        "name": "OSC_RES",+        "type": "output",+        "description": "Oscillator trim resistor connection; connect 18.2-kΩ 1% resistor to DVSSO for oscillator frequency calibration."+      },+      {+        "number": "17",+        "name": "DVSSO",+        "type": "power_in",+        "description": "Oscillator ground; oscillator trim resistor connects from OSC_RES to this pin."+      },+      {+        "number": "18",+        "name": "VR_DIG",+        "type": "power_out",+        "description": "Internally regulated 1.8-V digital supply; must not be used to power external devices."+      },+      {+        "number": "19",+        "name": "PDN",+        "type": "input",+        "description": "Active-low power-down input with internal pullup; initiates PWM stop sequence and noise shaper shutdown."+      },+      {+        "number": "20",+        "name": "LRCLK",+        "type": "input",+        "description": "I2S left/right clock (sample-rate clock) input with 5-V tolerance; supports 8 to 48-kHz sample rates."+      },+      {+        "number": "21",+        "name": "SCLK",+        "type": "input",+        "description": "I2S serial bit clock input (1.024 to 12.288-MHz at 32×, 48×, or 64×fS) with 5-V tolerance and 8-ns rise/fall time."+      },+      {+        "number": "22",+        "name": "SDIN",+        "type": "input",+        "description": "Serial audio data input supporting 16-bit, 20-bit, and 24-bit I2S, left-justified, and right-justified data formats."+      },+      {+        "number": "23",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C open-drain serial data line with internal pullup; requires external 4.7-kΩ pullup resistor to DVDD."+      },+      {+        "number": "24",+        "name": "SCL",+        "type": "input",+        "description": "I2C serial control clock input supporting 100-kHz and 400-kHz operation with 5-V tolerance."+      },+      {+        "number": "25",+        "name": "RESET",+        "type": "input",+        "description": "Active-low asynchronous reset input with internal pullup; must be held low for 100-µs minimum at power-up."+      },+      {+        "number": "26",+        "name": "STEST",+        "type": "input",+        "description": "Factory test pin; must be connected directly to DVSS for proper operation."+      },+      {+        "number": "27",+        "name": "DVDD",+        "type": "power_in",+        "description": "3.3-V digital power supply (3.0 to 3.6 V nominal); requires quality decoupling capacitors placed close to pin."+      },+      {+        "number": "28",+        "name": "DVSS",+        "type": "power_in",+        "description": "Digital ground connection."+      },+      {+        "number": "29",+        "name": "GND",+        "type": "power_in",+        "description": "Analog ground for power stage; should be connected to system ground."+      },+      {+        "number": "30",+        "name": "AGND",+        "type": "power_in",+        "description": "Local analog ground for power-stage output section; provides ground reference for output pins."+      },+      {+        "number": "31",+        "name": "VREG",+        "type": "power_out",+        "description": "Digital regulator output; not to be used for powering external circuitry."+      },+      {+        "number": "32",+        "name": "GVDD_OUT",+        "type": "power_out",+        "description": "Gate-drive regulator output derived from PVDD; supplies bootstrap charging diode for high-side gate drivers."+      },+      {+        "number": "33",+        "name": "BST_D",+        "type": "power_in",+        "description": "High-side bootstrap supply for half-bridge D gate driver; connect 10-nF ceramic capacitor to OUT_D."+      },+      {+        "number": "34",+        "name": "PVDD_CD",+        "type": "power_in",+        "description": "Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin."+      },+      {+        "number": "35",+        "name": "PVDD_CD",+        "type": "power_in",+        "description": "Power-supply input for half-bridges C and D (8 to 26.4 V); requires 100-nF ceramic decoupling capacitor placed close to pin."+      },+      {+        "number": "36",+        "name": "OUT_D",+        "type": "output",+        "description": "Half-bridge D PWM output pin for audio power amplification."+      },+      {+        "number": "37",+        "name": "PGND_CD",+        "type": "power_in",+        "description": "Power-stage ground for half-bridges C and D."+      },+      {+        "number": "38",+        "name": "PGND_CD",+        "type": "power_in",+        "description": "Power-stage ground for half-bridges C and D."+      },+      {+        "number": "39",+        "name": "OUT_C",+        "type": "output",+        "description": "Half-bridge C PWM output pin for audio power amplification."+      },+      {+        "number": "40",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "41",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "42",+        "name": "BST_C",+        "type": "power_in",+        "description": "High-side bootstrap supply for half-bridge C gate driver; connect 10-nF ceramic capacitor to OUT_C."+      },+      {+        "number": "43",+        "name": "BST_B",+        "type": "power_in",+        "description": "High-side bootstrap supply for half-bridge B gate driver; connect 10-nF ceramic capacitor to OUT_B."+      },+      {+        "number": "44",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "45",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection; may be left floating or connected to ground."+      },+      {+        "number": "46",+        "name": "OUT_B",+        "type": "output",+        "description": "Half-bridge B PWM output pin for audio power amplification."+      },+      {+        "number": "47",+        "name": "PGND_AB",+        "type": "power_in",+        "description": "Power-stage ground for half-bridges A and B."+      },+      {+        "number": "48",+        "name": "PGND_AB",+        "type": "power_in",+        "description": "Power-stage ground for half-bridges A and B."+      },+      {+        "number": "49",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Bootstrap pins (BST_A, BST_B, BST_C, BST_D) are classified as power_in but function as capacitive su",+          "exposed pad 49 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 71,+        "cost_usd": 0.8616,+        "at": "2026-09-26T22:12:07"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tas5731m",+        "pages": 71,+        "sha256": "b548f5b31dc8dd9b",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 49,+        "described": 49,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file