main
History Download
Ray Publish 0.1.0 026541f

STM6710LWB7F

STMicroelectronics · Monitors & Reset Circuits · SOT-23-6

STM6710LWB7F from STMicroelectronics, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 V1IN input Monitored input 1 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of ±0.4 µA max on the adjustable input.
2 V2IN power_in Input voltage 2 is also the STM6710 device power supply and is itself monitored, with an operating supply of 1.0 to 5.5 V (0 to T_max °C) or 1.2 to 5.5 V (-40 to T_max °C).
3 V3IN input Monitored input 3 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of less than ±0.2 µA on the adjustable input.
4 V4IN input Monitored input 4 is compared against a factory-set trip point or an adjustable threshold of 0.62 V typ set by an external divider, with input current of less than ±0.2 µA on the adjustable input.
5 GND power_in Ground pin for the power supply, tied to VSS.
6 RESET output Active-low open-drain reset output that goes low when any monitored input falls below its threshold, with a weak 10 µA internal pull-up to V2IN and a typical 200 ms reset timeout on the STM6710.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SOT-23-6
Category Power Supply Chip
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature TSTG -55 150 °C VCC off 11
Lead solder temperature TSLD 260 °C 10 seconds 11
Input or output voltage VIO -0.3 V max printed as VCC + 0.3 11
Supply voltage VCC -0.3 7 V 11
Output current IO 20 mA 11
V2IN supply voltage V2IN 1 5.5 V TA = 0 to T_max °C 12
V2IN supply voltage V2IN 1.2 5.5 V TA = -40 to T_max °C 12
Ambient operating temperature TA -40 105 °C 12
Reset threshold 2.5 V (-5%) Vrst 2.25 2.32 2.38 V VxIN falling 12
Reset threshold 1.8 V (-5%) Vrst 1.62 1.67 1.71 V VxIN falling 12
Adjustable reset threshold voltage Vrstxin 0.611 0.62 0.629 V VxIN decreasing 13
Reset timeout delay tREC 140 200 280 ms STM6710 13
RESET output low VOL 0.3 V V2IN, VCC = 5 V, ISINK = 2 mA 13
RESET output low VOL 0.4 V V2IN, VCC = 2.5 V, ISINK = 1.2 mA 13
RESET output high VOH 0.8 x V2IN VCC ≥ VTH, ISOURCE = -6 µA, RESET deasserted 13
Input current (1.8 V, 2.5 V, 5.0 V supplies) IxIN 25 40 µA VxIN nominal input voltage (1.8 V, 2.5 V, 5.0 V supplies) 12
Input current (V1IN adjustable) IxIN 0.4 µA V1IN = 0 to 0.85 V (for adjustable thresholds) 12
Input current (V3IN, V4IN adjustable) IxIN 0.2 µA V3IN, V4IN = 0 to 0.85 V (for adjustable thresholds) 12
VTH to reset asserted delay tRPD 30 µs VxIN falling at 10 mV/µs from VTH to (VTH -50 mV) 13
Hysteresis of VTH VHYST 0.3 % VTH 13
Reset threshold temperature coefficient TCVTH 60 ppm/°C 13
RESET output high source current IOH 10 µA V2IN ≥ 2.0 V, RESET deasserted 13

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: STM6710LWB7F
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6, generated on the KiCad land (body 1.625 x 2.925 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm6710lwb7f-etched.step / stm6710lwb7f-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm6710lwb7f.step / stm6710lwb7f.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (20 pp, sha256 c500f2ef39e8a69c, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF