component
STM32L562RET6P
Public Made by Adomby adom
STMicroelectronics ST Microelectronics, LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
STM32L562RET6P
STMicroelectronics · ST Microelectronics · LQFP-64(10x10)
STM32L562RET6P from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply (1.55 V to 3.6 V) for the RTC, the 32 kHz oscillator and backup registers when VDD is not present. |
| 2 | PC13 | bidirectional | 5 V-tolerant I/O supplied through the backup power switch, which sinks at most 3 mA, so output speed is limited to 2 MHz at 30 pF and it must not be used as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | 5 V-tolerant I/O on the backup power switch with the same 3 mA, 2 MHz / 30 pF output limits, also serving as the 32 kHz oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | 5 V-tolerant I/O on the backup power switch with the same 3 mA, 2 MHz / 30 pF output limits, also serving as the 32 kHz oscillator output OSC32_OUT. |
| 5 | PH0-OSC_IN | bidirectional | 5 V-tolerant I/O that also provides the OSC_IN high-speed oscillator input function. |
| 6 | PH1-OSC_OUT | bidirectional | 5 V-tolerant I/O that also provides the OSC_OUT high-speed oscillator output function. |
| 7 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; also provides ADC12_IN1. |
| 9 | PC1 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; also provides ADC12_IN2. |
| 10 | PC2 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; limited to 4 V when used by an analog peripheral such as the ADC, and also provides ADC12_IN3. |
| 11 | PC3 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides ADC12_IN4. |
| 12 | VSSA/VREF- | power_in | Analog ground; VREF- must always be equal to VSSA. |
| 13 | VDDA/VREF+ | power_in | Analog supply VDDA (1.62 V minimum for ADC/COMP, 3.6 V maximum) that is double-bonded with VREF+, so the internal voltage reference buffer is not available and must stay disabled on this package. |
| 14 | PA0 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides OPAMP1_VINP, ADC12_IN5 and WKUP1. |
| 15 | PA1 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides OPAMP1_VINM and ADC12_IN6. |
| 16 | PA2 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides ADC12_IN7, COMP1_INP and WKUP4/LSCO. |
| 17 | PA3 | bidirectional | 3.6 V-tolerant I/O with an analog switch supplied by VDDA; also provides OPAMP1_VOUT and ADC12_IN8. |
| 18 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 19 | VDD | power_in | Main supply 1.71 V to 3.6 V for the I/Os, internal regulator and system analog circuits. |
| 20 | PA4 | bidirectional | 3.6 V-tolerant I/O with an analog switch supplied by VDDA; also provides ADC12_IN9 and DAC1_OUT1. |
| 21 | PA5 | bidirectional | 3.6 V-tolerant I/O with an analog switch supplied by VDDA; also provides ADC12_IN10 and DAC1_OUT2. |
| 22 | PA6 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides OPAMP2_VINP and ADC12_IN11. |
| 23 | PA7 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; also provides OPAMP2_VINM and ADC12_IN12. |
| 24 | PC4 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides COMP1_INM and ADC12_IN13. |
| 25 | PB0 | bidirectional | 3.6 V-tolerant I/O with an analog switch supplied by VDDA; also provides OPAMP2_VOUT and ADC12_IN15. |
| 26 | PB1 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides COMP1_INM and ADC12_IN16. |
| 27 | PB2 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides RTC_OUT2 and COMP1_INP. |
| 28 | PB10 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include I2C2_SCL and I2C4_SCL. |
| 29 | PB11 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include I2C2_SDA and I2C4_SDA. |
| 30 | VDD12_1 | power_in | External SMPS supply input (VDD12, 1.05 V to 1.32 V) that bypasses the internal regulator; it needs no decoupling capacitor and cannot support any external load. |
| 31 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 32 | VDD | power_in | Main supply 1.71 V to 3.6 V for the I/Os, internal regulator and system analog circuits. |
| 33 | PB12 | bidirectional | 5 V-tolerant I/O; alternate functions include TIM1_BKIN, SPI2_NSS and USART3_CK. |
| 34 | PB13 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include I2C2_SCL, SPI2_SCK and LPUART1_CTS. |
| 35 | PB14 | bidirectional | 5 V-tolerant Fm+-capable I/O with USB Type-C PD dead-battery function (UCPD1_DB2). |
| 36 | PB15 | bidirectional | 5 V-tolerant I/O with USB Type-C PD capability (UCPD1_CC2); also provides RTC_REFIN. |
| 37 | PC6 | bidirectional | 5 V-tolerant I/O; alternate functions include TIM3_CH1, TIM8_CH1 and SDMMC1_D0DIR. |
| 38 | PC7 | bidirectional | 5 V-tolerant I/O; alternate functions include TIM3_CH2, TIM8_CH2 and SDMMC1_D123DIR. |
| 39 | PC8 | bidirectional | 5 V-tolerant I/O; alternate functions include TIM3_CH3, TIM8_CH3 and SDMMC1_D0. |
| 40 | PC9 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include TIM3_CH4, TIM8_CH4 and USB_NOE. |
| 41 | PA8 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include MCO, TIM1_CH1 and USART1_CK. |
| 42 | PA9 | bidirectional | 5 V-tolerant Fm+-capable I/O with USB function supplied by VDDUSB; alternate functions include TIM1_CH2 and USART1_TX. |
| 43 | PA10 | bidirectional | 5 V-tolerant Fm+-capable I/O with USB function supplied by VDDUSB; alternate functions include TIM1_CH3 and USART1_RX. |
| 44 | PA11 | bidirectional | 5 V-tolerant I/O with the USB_DM function supplied by VDDUSB; alternate functions include TIM1_CH4 and FDCAN1_RX. |
| 45 | PA12 | bidirectional | 5 V-tolerant I/O with the USB_DP function supplied by VDDUSB; alternate functions include TIM1_ETR and FDCAN1_TX. |
| 46 | PA13 | bidirectional | 5 V-tolerant I/O that after reset is the JTMS/SWDIO debug pin, with the internal pull-up activated. |
| 47 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 48 | VDDUSB | power_in | USB transceiver supply, 3.0 V to 3.6 V when USB is used; should be connected to VDD when USB is not used. |
| 49 | PA14 | bidirectional | 5 V-tolerant I/O that after reset is the JTCK/SWCLK debug pin, with the internal pull-down activated. |
| 50 | PA15 (JTDI) | bidirectional | USB Type-C PD capable 5 V-tolerant I/O (UCPD1_CC1) that after reset is the JTDI debug pin, with the internal pull-up activated. |
| 51 | PC10 | bidirectional | 5 V-tolerant I/O; alternate functions include TRACED1, SPI3_SCK and USART3_TX. |
| 52 | PC11 | bidirectional | 5 V-tolerant I/O; alternate functions include UART4_RX, USART3_RX and SDMMC1_D3. |
| 53 | PC12 | bidirectional | 5 V-tolerant I/O; alternate functions include TRACED3, UART5_TX and SDMMC1_CK. |
| 54 | PB3 | bidirectional | 5 V-tolerant I/O with an analog switch supplied by VDDA; also provides COMP2_INM and the JTDO/TRACESWO function. |
| 55 | PB4 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; after reset it is the NJTRST debug pin with the internal pull-up activated, and it also provides COMP2_INP. |
| 56 | PB5 | bidirectional | 5 V-tolerant I/O with USB Type-C PD dead-battery function (UCPD1_DB1); also provides COMP2_OUT and TIM16_BKIN. |
| 57 | PB6 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; also provides COMP2_INP and I2C1_SCL. |
| 58 | PB7 | bidirectional | 5 V-tolerant Fm+-capable I/O with an analog switch supplied by VDDA; also provides COMP2_INM, PVD_IN and I2C1_SDA. |
| 59 | PH3-BOOT0 | bidirectional | Dedicated BOOT0 pin with a 5 V-tolerant FT structure, also listed as an I/O with PH3 function. |
| 60 | PB8 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include I2C1_SCL, FDCAN1_RX and SDMMC1_D4. |
| 61 | PB9 | bidirectional | 5 V-tolerant Fm+-capable I/O; alternate functions include IR_OUT, I2C1_SDA, FDCAN1_TX and SDMMC1_D5. |
| 62 | VDD12_2 | power_in | External SMPS supply input (VDD12, 1.05 V to 1.32 V) that bypasses the internal regulator; it needs no decoupling capacitor and cannot support any external load. |
| 63 | VSS | power_in | Ground reference; all voltages are referenced to VSS. |
| 64 | VDD | power_in | Main supply 1.71 V to 3.6 V for the I/Os, internal regulator and system analog circuits. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VDDIO2, VDDUSB, VBAT, VDDSMPS, VREF+) | VDDX - VSS | -0.3 | 4 | V | Voltage characteristics, all main power pins | 147 | |
| External SMPS supply voltage | VDD12 - VSS | -0.3 | 1.4 | V | All ranges 0/1/2 | 147 | |
| Input voltage on FT_xxx pins except FT_c pins | VIN | -0.3 | V | Max = Min(Min(VDD, VDDA, VDDIO2, VDDUSB, VDDSMPS) + 4.0, 6.0), formula as printed (notes 3, 4) | 147 | ||
| Input voltage on FT_c pins | VIN | -0.3 | 5.5 | V | FT_c pins | 147 | |
| Input voltage on any other pins | VIN | -0.3 | 4 | V | Other pins; FT_a max 4 V when used by analog peripheral (note 5) | 147 | |
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 148 | |||
| Variations between all the different ground pins | /VSSx-VSS/ | 50 | mV | Include VREF- pin | 148 | ||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 160 | mA | 148 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 160 | mA | 148 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 148 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 148 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | Sink | 148 | ||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | Sink, FT_f pin | 148 | ||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | Source | 148 | ||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | Sink; current must be distributed over all I/Os (note 3) | 148 | ||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | Source; current must be distributed over all I/Os (note 3) | 148 | ||
| Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | Negative injection induced by VIN < VSS (note 5) | 148 | |
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 148 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | -25 | 25 | mA | Absolute sum of negative injected currents (note 6) | 148 | |
| Storage temperature range | TSTG | -65 | 150 | °C | 149 | ||
| Maximum junction temperature | TJ | 150 | °C | 149 | |||
| Internal AHB clock frequency | fHCLK | 0 | 110 | MHz | 149 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 110 | MHz | 149 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 110 | MHz | 149 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | Note 1: functionality guaranteed down to VBOR0 min after reset release | 149 | |
| Standard operating voltage (external SMPS VDD12) | VDD12 | 1.14 | 1.32 | V | Up to 110 MHz | 149 | |
| Standard operating voltage (external SMPS VDD12) | VDD12 | 1.08 | 1.32 | V | Up to 80 MHz | 149 | |
| Standard operating voltage (external SMPS VDD12) | VDD12 | 1.05 | 1.32 | V | Up to 26 MHz; for Flash erase and program VDD12 min must be 1.08 V (note 2) | 149 | |
| PG[15:2] I/Os supply voltage | VDDIO2 | 1.08 | 3.6 | V | At least one I/O in PG[15:2] used | 149 | |
| PG[15:2] I/Os supply voltage | VDDIO2 | 0 | 3.6 | V | PG[15:2] not used | 149 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 149 | |
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 149 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | VREFBUF used | 149 | |
| Analog supply voltage | VDDA | 0 | 3.6 | V | ADC, DAC, OPAMP, COMP, VREFBUF not used | 149 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 150 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 150 | |
| USB supply voltage | VDDUSB | 0 | 3.6 | V | USB not used | 150 | |
| I/O input voltage (TT_xx) | VIN | -0.3 | V | Max = VDDIOx+0.3 as printed | 150 | ||
| I/O input voltage (FT_c) | VIN | -0.3 | 5 | V | FT_c I/O | 150 | |
| I/O input voltage (all except FT_c and TT_xx) | VIN | -0.3 | V | Max = MIN(MIN(VDD, VDDA, VDDIO2, VDDUSB) + 3.6 V, 5.5 V) as printed (notes 3, 4) | 150 | ||
| Ambient temperature, maximum power dissipation (suffix 6) | TA | -40 | 85 | °C | Suffix 6 version | 150 | |
| Ambient temperature, low-power dissipation (suffix 6) | TA | -40 | 105 | °C | Suffix 6 version, low-power dissipation state | 150 | |
| Junction temperature range (suffix 6) | TJ | -40 | 105 | °C | Suffix 6 version | 150 | |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 153 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 153 |
| Brown-out reset threshold 1 | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 153 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 153 |
| Brown-out reset threshold 2 | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 153 |
| Brown-out reset threshold 2 | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 153 |
| Brown-out reset threshold 3 | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 153 |
| Brown-out reset threshold 3 | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 153 |
| Brown-out reset threshold 4 | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 153 |
| Brown-out reset threshold 4 | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 153 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40°C < TA < +130°C | 155 |
| Internal reference voltage spread over the temperature range | ΔVREFINT | 5 | 7.5 | mV | VDD = 3 V | 155 | |
| Average temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 155 | |
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25°C | 155 | |
| Average voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 155 | |
| Supply current in Run mode | IDD(Run) | 16.7 | 19.07 | mA | Voltage range 0, fHCLK = 110 MHz, code from Flash single bank ICACHE ON 2-way, all peripherals disabled, TA = 25°C | 158 | |
| Supply current in Run mode | IDD(Run) | 23.7 | 56.59 | mA | Voltage range 0, fHCLK = 110 MHz, code from Flash single bank ICACHE ON 2-way, all peripherals disabled, TA = 125°C | 158 |
CAD (KiCad official)
- Symbol:
STM32L562RET6P - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32l562ret6p-etched.step/stm32l562ret6p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l562ret6p.step/stm32l562ret6p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (341 pp, sha256
bc9dcd89da9546a8, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).