3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32L452RCT6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
STM32L452RCT6 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup domain supply for the RTC and backup registers, 1.55 V to 3.6 V per Table 23. |
| 2 | PC13 | bidirectional | FT GPIO (RTC_TAMP1/RTC_TS/RTC_OUT/WKUP2) supplied through the power switch, which sinks only 3 mA, so output use is limited to 2 MHz at 30 pF and it must not be used as a current source. |
| 3 | PC14-OSC32_IN (PC14) | bidirectional | FT GPIO on the power-switch supply (3 mA limit) that doubles as the 32 kHz LSE oscillator input OSC32_IN. |
| 4 | PC15-OSC32_OUT (PC15) | bidirectional | FT GPIO on the power-switch supply (3 mA limit) that doubles as the 32 kHz LSE oscillator output OSC32_OUT. |
| 5 | PH0-OSC_IN (PH0) | bidirectional | FT GPIO that doubles as the high-speed oscillator input OSC_IN for the external crystal (4 to 48 MHz). |
| 6 | PH1-OSC_OUT (PH1) | bidirectional | FT GPIO that doubles as the high-speed oscillator output OSC_OUT for the external crystal (4 to 48 MHz). |
| 7 | NRST | bidirectional | Bidirectional active reset pin with an embedded weak pull-up resistor (RST I/O structure). |
| 8 | PC0 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with ADC1_IN1 analog input and LPUART1_RX, LPTIM1_IN1 alternate functions. |
| 9 | PC1 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with ADC1_IN2 analog input and LPUART1_TX, LPTIM1_OUT alternate functions. |
| 10 | PC2 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN3 analog input and SPI2_MISO, LPTIM1_IN2 alternate functions. |
| 11 | PC3 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN4 analog input and SPI2_MOSI, LPTIM1_ETR alternate functions. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative ADC reference; per the Table 76 note VREF- can be internally connected to VSSA depending on package. |
| 13 | VDDA/VREF+ | power_in | Analog supply, 1.62 V to 3.6 V when ADC or COMP is used, and positive ADC reference VREF+ (per Table 23 and Table 76). |
| 14 | PA0 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN5 analog input, TIM2_CH1/TIM2_ETR and USART2_CTS alternate functions, and RTC_TAMP2/WKUP1 wakeup. |
| 15 | PA1 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN6 and OPAMP1_VINM analog functions, and TIM2_CH2, SPI1_SCK and USART2_RTS_DE alternate functions. |
| 16 | PA2 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN7, COMP2_INM and WKUP4/LSCO functions, and TIM2_CH3, USART2_TX and LPUART1_TX alternate functions. |
| 17 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant) with ADC1_IN8, OPAMP1_VOUT and COMP2_INP functions, and TIM2_CH4, USART2_RX and LPUART1_RX alternate functions. |
| 18 | VSS | power_in | Ground supply pin; must always be connected to the external ground within the permitted range. |
| 19 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V standard operating voltage (Table 23). |
| 20 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant) with ADC1_IN9, DAC1_OUT1, COMP1_INM and COMP2_INM functions, and SPI1_NSS, SPI3_NSS and USART2_CK alternate functions. |
| 21 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant) with ADC1_IN10, COMP1_INM and COMP2_INM functions, and TIM2_CH1, TIM2_ETR and SPI1_SCK alternate functions. |
| 22 | PA6 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN11 analog input and TIM1_BKIN, TIM3_CH1, SPI1_MISO and LPUART1_CTS alternate functions. |
| 23 | PA7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with ADC1_IN12 analog input and TIM1_CH1N, TIM3_CH2, I2C3_SCL and SPI1_MOSI alternate functions. |
| 24 | PC4 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN13 and COMP1_INM functions, and USART3_TX alternate function. |
| 25 | PC5 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN14, COMP1_INP and WKUP5 functions, and USART3_RX alternate function. |
| 26 | PB0 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN15 analog input and TIM1_CH2N, TIM3_CH3, SPI1_NSS and USART3_CK alternate functions. |
| 27 | PB1 | bidirectional | FT_a I/O (5 V tolerant) with ADC1_IN16 and COMP1_INM functions, and TIM1_CH3N, TIM3_CH4, USART3_RTS_DE and LPUART1_RTS_DE alternate functions. |
| 28 | PB2 | bidirectional | FT_a I/O (5 V tolerant) with COMP1_INP function, and RTC_OUT, LPTIM1_OUT and I2C3_SMBA alternate functions. |
| 29 | PB10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH3, I2C4_SCL, I2C2_SCL, SPI2_SCK, USART3_TX and LPUART1_RX alternate functions. |
| 30 | PB11 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM2_CH4, I2C4_SDA, I2C2_SDA, USART3_RX and LPUART1_TX alternate functions. |
| 31 | VSS | power_in | Ground supply pin; must always be connected to the external ground within the permitted range. |
| 32 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V standard operating voltage (Table 23). |
| 33 | PB12 | bidirectional | FT I/O (5 V tolerant) with TIM1_BKIN, I2C2_SMBA, SPI2_NSS, USART3_CK and CAN1_RX alternate functions. |
| 34 | PB13 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH1N, I2C2_SCL, SPI2_SCK, USART3_CTS and CAN1_TX alternate functions. |
| 35 | PB14 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH2N, I2C2_SDA, SPI2_MISO, USART3_RTS_DE and TIM15_CH1 alternate functions. |
| 36 | PB15 | bidirectional | FT I/O (5 V tolerant) with RTC_REFIN, TIM1_CH3N, SPI2_MOSI and SAI1_SD_A alternate functions. |
| 37 | PC6 | bidirectional | FT I/O (5 V tolerant) with TIM3_CH1, DFSDM1_CKIN3, TSC_G4_IO1 and SDMMC1_D6 alternate functions. |
| 38 | PC7 | bidirectional | FT I/O (5 V tolerant) with TIM3_CH2, DFSDM1_DATIN3, TSC_G4_IO2 and SDMMC1_D7 alternate functions. |
| 39 | PC8 | bidirectional | FT I/O (5 V tolerant) with TIM3_CH3, TSC_G4_IO3 and SDMMC1_D0 alternate functions. |
| 40 | PC9 | bidirectional | FT I/O (5 V tolerant) with TIM3_CH4, TSC_G4_IO4, USB_NOE and SDMMC1_D1 alternate functions. |
| 41 | PA8 | bidirectional | FT I/O (5 V tolerant) with MCO clock output and TIM1_CH1, USART1_CK, SAI1_SCK_A and LPTIM2_OUT alternate functions. |
| 42 | PA9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH2, I2C1_SCL, USART1_TX and SAI1_FS_A alternate functions. |
| 43 | PA10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH3, I2C1_SDA, USART1_RX and USB_CRS_SYNC alternate functions. |
| 44 | PA11 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_CH4, SPI1_MISO, USART1_CTS, CAN1_RX and USB_DM alternate functions. |
| 45 | PA12 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, CAN1_TX and USB_DP alternate functions. |
| 46 | PA13 | bidirectional | FT I/O (5 V tolerant) configured as the JTMS/SWDIO debug function after reset, with the internal pull-up activated. |
| 47 | VSS | power_in | Ground supply pin; must always be connected to the external ground within the permitted range. |
| 48 | VDDUSB | power_in | USB supply pin, 3.0 V to 3.6 V when USB is used (Table 23). |
| 49 | PA14 | bidirectional | FT I/O (5 V tolerant) configured as the JTCK/SWCLK debug function after reset, with the internal pull-down activated. |
| 50 | PA15 | bidirectional | FT I/O (5 V tolerant) configured as the JTDI debug function after reset, with the internal pull-up activated, and TIM2_CH1, USART2_RX and SPI1_NSS alternate functions. |
| 51 | PC10 | bidirectional | FT I/O (5 V tolerant) with TRACED1, SPI3_SCK, USART3_TX, UART4_TX and SDMMC1_D2 alternate functions. |
| 52 | PC11 | bidirectional | FT I/O (5 V tolerant) with SPI3_MISO, USART3_RX, UART4_RX and SDMMC1_D3 alternate functions. |
| 53 | PC12 | bidirectional | FT I/O (5 V tolerant) with TRACED3, SPI3_MOSI, USART3_CK and SDMMC1_CK alternate functions. |
| 54 | PD2 | bidirectional | FT I/O (5 V tolerant) with TRACED2, TIM3_ETR, USART3_RTS_DE, TSC_SYNC and SDMMC1_CMD alternate functions. |
| 55 | PB3 | bidirectional | FT_a I/O (5 V tolerant) configured as the JTDO/TRACESWO debug function after reset, with TIM2_CH2, SPI1_SCK and SPI3_SCK alternate functions. |
| 56 | PB4 | bidirectional | FT_fa I/O (5 V tolerant) configured as the NJTRST debug function after reset, with internal pull-up activated, and TIM3_CH1, I2C3_SDA and SPI1_MISO alternate functions. |
| 57 | PB5 | bidirectional | FT I/O (5 V tolerant) with LPTIM1_IN1, TIM3_CH2, CAN1_RX, I2C1_SMBA, SPI1_MOSI and USART1_CK alternate functions. |
| 58 | PB6 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with COMP2_INP function, and LPTIM1_ETR, I2C1_SCL, I2C4_SCL, USART1_TX and CAN1_TX alternate functions. |
| 59 | PB7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable) with COMP2_INM and PVD_IN functions, and LPTIM1_IN2, I2C1_SDA, I2C4_SDA, USART1_RX and UART4_CTS alternate functions. |
| 60 | PH3-BOOT0 | bidirectional | FT I/O (5 V tolerant) shared with the BOOT0 boot configuration pin, which selects the boot mode. |
| 61 | PB8 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with I2C1_SCL, CAN1_RX, SDMMC1_D4, SAI1_MCLK_A and TIM16_CH1 alternate functions. |
| 62 | PB9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with IR_OUT, I2C1_SDA, SPI2_NSS, CAN1_TX and SDMMC1_D5 alternate functions. |
| 63 | VSS | power_in | Ground supply pin; must always be connected to the external ground within the permitted range. |
| 64 | VDD | power_in | Main supply pin, 1.71 V to 3.6 V standard operating voltage (Table 23). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (VDD, VDDA, VDDUSB, VBAT) | VDDX - VSS | -0.3 | 4 | V | 88 | ||
| External SMPS supply voltage | VDD12 - VSS | -0.3 | 1.32 | V | 88 | ||
| Input voltage on any other pins | VIN | 4 | V | Printed min is VSS-0.3 | 88 | ||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 140 | mA | 89 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 140 | mA | 89 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 89 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 89 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 89 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 89 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 89 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 89 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 89 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 90 | ||
| Maximum junction temperature | TJ | 150 | °C | 90 | |||
| Internal AHB clock frequency | fHCLK | 0 | 80 | MHz | 91 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 80 | MHz | 91 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 80 | MHz | 91 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 91 | ||
| Standard operating voltage, full frequency range | VDD12 | 1.08 | 1.32 | V | Full frequency range | 91 | |
| Standard operating voltage, up to 26 MHz | VDD12 | 1.05 | V | Up to 26 MHz | 91 | ||
| Analog supply voltage, ADC or COMP used | VDDA | 1.62 | 3.6 | V | ADC or COMP used | 91 | |
| Analog supply voltage, DAC or OPAMP used | VDDA | 1.8 | 3.6 | V | DAC or OPAMP used | 91 | |
| Analog supply voltage, VREFBUF used | VDDA | 2.4 | 3.6 | V | VREFBUF used | 91 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 91 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 91 | |
| I/O input voltage, TT_xx I/O | VIN | -0.3 | V | TT_xx I/O; printed max is VDDIOx+0.3 | 91 | ||
| Power dissipation LQFP64 | PD | 345 | mW | TA = 85 °C for suffix 6 | 91 | ||
| Power dissipation LQFP64 | PD | 86 | mW | TA = 125 °C for suffix 3 | 91 | ||
| Ambient temperature, suffix 6, maximum power dissipation | TA | -40 | 85 | °C | Maximum power dissipation | 91 | |
| Ambient temperature, suffix 6, low-power dissipation | TA | -40 | 105 | °C | Low-power dissipation | 91 | |
| Ambient temperature, suffix 3, maximum power dissipation | TA | -40 | 125 | °C | Maximum power dissipation | 91 | |
| Ambient temperature, suffix 3, low-power dissipation | TA | -40 | 130 | °C | Low-power dissipation | 91 | |
| Junction temperature range, suffix 6 | TJ | -40 | 105 | °C | Suffix 6 version | 91 | |
| Junction temperature range, suffix 3 | TJ | -40 | 130 | °C | Suffix 3 version | 91 | |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | μs | VDD rising | 92 | |
| Brown-out reset threshold 0, rising edge | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 92 |
| Brown-out reset threshold 0, falling edge | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 92 |
| Brown-out reset threshold 1, rising edge | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 93 |
| Brown-out reset threshold 1, falling edge | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 93 |
| Programmable voltage detector threshold 0, rising edge | VPVD0 | 2.1 | 2.15 | 2.19 | V | Rising edge | 93 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 95 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | µs | 95 | |||
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | 8 | 12 | µs | 95 | ||
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | 12.5 | 20 | µA | 95 | ||
| Internal reference voltage spread over the temperature range | ∆VREFINT | 5 | 7.5 | mV | VDD = 3 V | 95 | |
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40°C < TA < +130°C | 95 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 95 | |
| 1/4 reference voltage | VREFINT_DIV1 | 24 | 25 | 26 | % VREFINT | 95 | |
| 1/2 reference voltage | VREFINT_DIV2 | 49 | 50 | 51 | % VREFINT | 95 | |
| 3/4 reference voltage | VREFINT_DIV3 | 74 | 75 | 76 | % VREFINT | 95 | |
| Supply current in Run mode, Range 1 | IDD_ALL(Run) | 8.45 | 9.45 | mA | Range 1, fHCLK = 80 MHz, 25 °C, all peripherals disabled | 98 | |
| Supply current in Low-power run mode | IDD_ALL(LPRun) | 225 | 275 | µA | fHCLK = fMSI = 2 MHz, 25 °C, all peripherals disabled | 98 | |
| Supply current in sleep mode, Range 1 | IDD_ALL(Sleep) | 2.3 | 2.55 | mA | Range 1, fHCLK = 80 MHz, 25 °C, all peripherals disabled | 109 | |
| Supply current in Stop 2 mode, RTC disabled | IDD_ALL(Stop 2) | 2.05 | 4.1 | µA | VDD = 3 V, 25 °C | 111 | |
| Supply current in Stop 1 mode, RTC disabled | IDD_ALL(Stop 1) | 9.9 | 17.5 | µA | VDD = 3 V, 25 °C | 113 | |
| Supply current in Standby mode, RTC disabled, no independent watchdog | IDD_ALL(Standby) | 125 | 290 | nA | VDD = 3 V, 25 °C | 115 | |
| Supply current in Shutdown mode, RTC disabled | IDD_ALL(Shutdown) | 37 | 105 | nA | VDD = 3 V, 25 °C | 116 | |
| Backup domain supply current, RTC enabled, clocked by LSE bypassed at 32768 Hz | IDD_VBAT(VBAT) | 285 | nA | VBAT = 3 V, 25 °C | 117 | ||
| Backup domain supply current, RTC disabled | IDD_VBAT(VBAT) | 5 | nA | VBAT = 3 V, 25 °C | 117 |
CAD (KiCad official)
- Symbol:
STM32L452RCT6 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32l452rct6-etched.step/stm32l452rct6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l452rct6.step/stm32l452rct6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (210 pp, sha256
eeeaa72ec16c85ea, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).