3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32L412KBU6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · UFQFPN-32(5x5)
STM32L412KBU6 from STMicroelectronics, in a UFQFPN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V (Table 21). |
| 2 | PC14-OSC32_IN (PC14) | bidirectional | FT I/O (5 V tolerant) whose default function is PC14, also usable as OSC32_IN for the 32.768 kHz LSE crystal, with EVENTOUT as alternate function. |
| 3 | PC15-OSC32_OUT (PC15) | bidirectional | FT I/O (5 V tolerant) whose default function is PC15, also usable as OSC32_OUT for the 32.768 kHz LSE crystal, with EVENTOUT as alternate function. |
| 4 | NRST | bidirectional | Bidirectional reset pin with an embedded weak pull-up resistor (RST I/O structure). |
| 5 | VDDA/VREF+ | power_in | Combined analog supply and VREF+ pin on this package; VDDA must be at least 1.62 V when the ADC or COMP is used and at least 1.8 V when the OPAMP is used, up to 3.6 V (Table 21). |
| 6 | PA0-CK_IN | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, USART2_CTS, COMP1_OUT, TIM2_ETR and EVENTOUT alternate functions, and OPAMP1_VINP, COMP1_INM, ADC1_IN5, RTC_TAMP2/WKUP1 and CK_IN additional functions. |
| 7 | PA1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH2, I2C1_SMBA, SPI1_SCK, USART2_RTS_DE, TIM15_CH1N and EVENTOUT alternate functions, and OPAMP1_VINM, COMP1_INP and ADC1_IN6 additional functions. |
| 8 | PA2 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM2_CH3, USART2_TX, LPUART1_TX, QUADSPI_BK1_NCS, TIM15_CH1 and EVENTOUT alternate functions, and ADC12_IN7 and WKUP4/LSCO additional functions. |
| 9 | PA3 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH4, USART2_RX, LPUART1_RX, QUADSPI_CLK, TIM15_CH2 and EVENTOUT alternate functions, and OPAMP1_VOUT and ADC12_IN8 additional functions. |
| 10 | PA4 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with SPI1_NSS, USART2_CK, LPTIM2_OUT and EVENTOUT alternate functions, and COMP1_INM and ADC12_IN9 additional functions. |
| 11 | PA5 | bidirectional | TT_a I/O (3.6 V tolerant, analog switch supplied by VDDA) with TIM2_CH1, TIM2_ETR, SPI1_SCK, LPTIM2_ETR and EVENTOUT alternate functions, and COMP1_INM and ADC12_IN10 additional functions. |
| 12 | PA6 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TIM1_BKIN, SPI1_MISO, COMP1_OUT, USART3_CTS, LPUART1_CTS, QUADSPI_BK1_IO3, TIM16_CH1 and EVENTOUT alternate functions, and ADC12_IN11 additional function. |
| 13 | PA7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with TIM1_CH1N, I2C3_SCL, SPI1_MOSI, QUADSPI_BK1_IO2 and EVENTOUT alternate functions, and ADC12_IN12 additional function. |
| 14 | PB0 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TRACED0, TIM1_CH2N, SPI1_NSS, USART3_CK, QUADSPI_BK1_IO1, COMP1_OUT and EVENTOUT alternate functions, and ADC12_IN15 additional function. |
| 15 | PB1 | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) with TRACED1, TIM1_CH3N, USART3_RTS_DE, LPUART1_RTS_DE, QUADSPI_BK1_IO0, LPTIM2_IN1 and EVENTOUT alternate functions, and COMP1_INM and ADC12_IN16 additional functions. |
| 16 | VSS | power_in | Ground pin; all VSS pins must be connected to the external ground within the permitted range (Table 18 notes). |
| 17 | VDD | power_in | Main power supply pin; the standard operating voltage is 1.71 V to 3.6 V (Table 21). |
| 18 | PA8 | bidirectional | FT I/O (5 V tolerant) with MCO, TIM1_CH1, USART1_CK and LPTIM2_OUT alternate functions and EVENTOUT. |
| 19 | PA9 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH2, I2C1_SCL, USART1_TX, TIM15_BKIN and EVENTOUT alternate functions. |
| 20 | PA10 | bidirectional | FT_f I/O (5 V tolerant, Fm+ capable) with TIM1_CH3, I2C1_SDA, USART1_RX, USB_CRS_SYNC and EVENTOUT alternate functions. |
| 21 | PA11 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_CH4, TIM1_BKIN2, SPI1_MISO, COMP1_OUT, USART1_CTS, USB_DM, TIM1_BKIN2_COMP1 and EVENTOUT alternate functions. |
| 22 | PA12 | bidirectional | FT_u I/O (5 V tolerant, USB function supplied by VDDUSB) with TIM1_ETR, SPI1_MOSI, USART1_RTS_DE, USB_DP and EVENTOUT alternate functions. |
| 23 | PA13 (JTMS/SWDIO) | bidirectional | FT I/O (5 V tolerant) whose function after reset is JTMS/SWDIO, with IR_OUT, USB_NOE and EVENTOUT alternate functions. |
| 24 | PA14 (JTCK/SWCLK) | bidirectional | FT I/O (5 V tolerant) whose function after reset is JTCK/SWCLK, with LPTIM1_OUT, I2C1_SMBA and EVENTOUT alternate functions. |
| 25 | PA15 (JTDI) | bidirectional | FT I/O (5 V tolerant) whose function after reset is JTDI, with TIM2_CH1, TIM2_ETR, USART2_RX, SPI1_NSS, USART3_RTS_DE, TSC_G3_IO1 and EVENTOUT alternate functions. |
| 26 | PB3 (JTDO/TRACESWO) | bidirectional | FT_a I/O (5 V tolerant, analog switch supplied by VDDA) whose function after reset is JTDO/TRACESWO, with TIM2_CH2, SPI1_SCK, USART1_RTS_DE and EVENTOUT alternate functions. |
| 27 | PB4 (NJTRST) | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) whose function after reset is NJTRST, with I2C3_SDA, SPI1_MISO, USART1_CTS, TSC_G2_IO1 and EVENTOUT alternate functions. |
| 28 | PB5 | bidirectional | FT I/O (5 V tolerant) with TRACED2, LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI, USART1_CK, TSC_G2_IO2, TIM16_BKIN and EVENTOUT alternate functions. |
| 29 | PB6 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with TRACED3, LPTIM1_ETR, I2C1_SCL, USART1_TX, TSC_G2_IO3, TIM16_CH1N and EVENTOUT alternate functions. |
| 30 | PB7 | bidirectional | FT_fa I/O (5 V tolerant, Fm+ capable, analog switch supplied by VDDA) with TRACECK, LPTIM1_IN2, I2C1_SDA, USART1_RX, TSC_G2_IO4 and EVENTOUT alternate functions, and PVD_IN additional function. |
| 31 | PH3-BOOT0 (BOOT0) | bidirectional | FT I/O (5 V tolerant) whose function after reset is BOOT0 (boot configuration), with EVENTOUT as alternate function; boot modes are described in Section 3.7. |
| 32 | VSS | power_in | Ground pin; all VSS pins must be connected to the external ground within the permitted range (Table 18 notes). |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | UFQFPN-32(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage on FT_xxx pins (min; max is a formula) | VIN | -0.3 | V | 75 | |||
| External main supply voltage (VDD, VDDA, VDDUSB, VBAT) | VDDX - VSS | -0.3 | 4 | V | 75 | ||
| Input voltage on TT_xx pins | VIN | -0.3 | 4 | V | 75 | ||
| Input voltage on any other pins | VIN | -0.3 | 4 | V | 75 | ||
| Variations between different VDDX power pins of the same domain | /ΔVDDx/ | 50 | mV | 76 | |||
| Variations between all the different ground pins (include VREF-) | /VSSx-VSS/ | 50 | mV | 76 | |||
| Total current into sum of all VDD power lines (source) | ∑IVDD | 140 | mA | 76 | |||
| Total current out of sum of all VSS ground lines (sink) | ∑IVSS | 140 | mA | 76 | |||
| Maximum current into each VDD power pin (source) | IVDD(PIN) | 100 | mA | 76 | |||
| Maximum current out of each VSS ground pin (sink) | IVSS(PIN) | 100 | mA | 76 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 20 | mA | 76 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 76 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 20 | mA | 76 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 76 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 100 | mA | 76 | |||
| Injected current on FT_xxx, TT_xx, RST and B pins, except PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 76 | ||
| Injected current on PA4, PA5 | IINJ(PIN) | -5 | 0 | mA | 76 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 76 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 77 | ||
| Maximum junction temperature | TJ | 150 | °C | 77 | |||
| Internal AHB clock frequency | fHCLK | 0 | 80 | MHz | 78 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 80 | MHz | 78 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 80 | MHz | 78 | ||
| Standard operating voltage | VDD | 1.71 | 3.6 | V | 78 | ||
| Analog supply voltage | VDDA | 1.62 | V | ADC or COMP used | 78 | ||
| Analog supply voltage | VDDA | 1.8 | 3.6 | V | OPAMP used | 78 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 78 | ||
| USB supply voltage | VDDUSB | 3 | 3.6 | V | USB used | 78 | |
| USB supply voltage | VDDUSB | 0 | 3.6 | V | USB not used | 78 | |
| I/O input voltage (max is VDDIOx+0.3 V, formula) | VIN | -0.3 | V | TT_xx I/O | 78 | ||
| I/O input voltage (max is a formula) | VIN | -0.3 | V | All I/O except TT_xx | 78 | ||
| Power dissipation (UFQFPN32) | PD | 541 | mW | TA = 85 °C for suffix 6 | 78 | ||
| Ambient temperature for suffix 6 version | TA | -40 | 85 | °C | Maximum power dissipation | 79 | |
| Ambient temperature for suffix 6 version | TA | -40 | 105 | °C | Low-power dissipation | 79 | |
| Junction temperature range, suffix 6 version | TJ | -40 | 105 | °C | Suffix 6 version | 79 | |
| Reset temporization after BOR0 is detected | tRSTTEMPO | 250 | 400 | µs | VDD rising | 79 | |
| Brown-out reset threshold 0 | VBOR0 | 1.62 | 1.66 | 1.7 | V | Rising edge | 79 |
| Brown-out reset threshold 0 | VBOR0 | 1.6 | 1.64 | 1.69 | V | Falling edge | 79 |
| Brown-out reset threshold 1 | VBOR1 | 2.06 | 2.1 | 2.14 | V | Rising edge | 80 |
| Brown-out reset threshold 1 | VBOR1 | 1.96 | 2 | 2.04 | V | Falling edge | 80 |
| Brown-out reset threshold 2 | VBOR2 | 2.26 | 2.31 | 2.35 | V | Rising edge | 80 |
| Brown-out reset threshold 2 | VBOR2 | 2.16 | 2.2 | 2.24 | V | Falling edge | 80 |
| Brown-out reset threshold 3 | VBOR3 | 2.56 | 2.61 | 2.66 | V | Rising edge | 80 |
| Brown-out reset threshold 3 | VBOR3 | 2.47 | 2.52 | 2.57 | V | Falling edge | 80 |
| Brown-out reset threshold 4 | VBOR4 | 2.85 | 2.9 | 2.95 | V | Rising edge | 80 |
| Brown-out reset threshold 4 | VBOR4 | 2.76 | 2.81 | 2.86 | V | Falling edge | 80 |
| Hysteresis voltage of BORH (except BORH0) and PVD | Vhyst_BOR_PVD | 100 | mV | 80 | |||
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40 °C < TA < +130 °C | 82 |
| ADC sampling time when reading the internal reference voltage | tS_vrefint | 4 | µs | 82 | |||
| Temperature coefficient | TCoeff | 30 | 50 | ppm/°C | -40 °C < TA < +130 °C | 82 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 82 | |
| Supply current in Run mode, Range 1 | IDD_ALL(Run) | 7.3 | 7.75 | mA | fHCLK = 80 MHz; all peripherals disabled; TA = 25 °C | 85 | |
| Supply current in Low-power run mode | IDD_ALL(LPRun) | 190 | 235 | µA | fHCLK = fMSI = 2 MHz; all peripherals disabled; TA = 25 °C | 85 | |
| Supply current in Stop 2 mode | IDD_ALL(Stop 2) | 0.79 | 2.1 | µA | RTC disabled; VDD = 3 V; TA = 25 °C | 98 | |
| Supply current in Stop 1 mode | IDD_ALL(Stop 1) | 4 | 7.3 | µA | RTC disabled; VDD = 3 V; TA = 25 °C | 101 | |
| Supply current in Standby mode (backup registers retained) | IDD_ALL(Standby) | 120 | 215 | nA | No independent watchdog; RTC disabled; VDD = 3 V; TA = 25 °C | 103 | |
| Supply current in Shutdown mode (backup registers retained) | IDD_ALL(Shutdown) | 31 | 97 | nA | RTC disabled; VDD = 3 V; TA = 25 °C | 106 |
CAD (KiCad official)
- Symbol:
STM32L412KBU6 - Footprint:
Package_DFN_QFN:UFQFPN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm - 3D model: UFQFPN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
stm32l412kbu6-etched.step/stm32l412kbu6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l412kbu6.step/stm32l412kbu6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (193 pp, sha256
5104ae3be2936485, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).