component
STM32L151ZET6
Public Made by Adomby adom
STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-144(20x20). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
README
markdownSTM32L151ZET6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · LQFP-144(20x20)
STM32L151ZET6 from STMicroelectronics, in a LQFP-144(20x20). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PE2 | bidirectional | 5 V tolerant (FT) I/O; default function PE2 after reset; alternate functions TIM3_ETR, LCD_SEG38, TRACECLK. |
| 2 | PE3 | bidirectional | 5 V tolerant (FT) I/O; default function PE3 after reset; alternate functions TIM3_CH1, LCD_SEG39, TRACED0. |
| 3 | PE4 | bidirectional | 5 V tolerant (FT) I/O; default function PE4 after reset; alternate functions TIM3_CH2, TRACED1. |
| 4 | PE5 | bidirectional | 5 V tolerant (FT) I/O; default function PE5 after reset; alternate functions TIM9_CH1, TRACED2. |
| 5 | PE6-WKUP3 | bidirectional | 5 V tolerant (FT) I/O; default function PE6; alternate functions TIM9_CH2, TRACED3; additional functions WKUP3, RTC_TAMP3. |
| 6 | VLCD | power_in | LCD power supply pin per Table 8; footnote 3 states it applies to STM32L152xE only and that on STM32L151xE devices this pin should be connected to VDD. |
| 7 | PC13-WKUP2 | bidirectional | 5 V tolerant (FT) I/O; default function PC13; additional functions WKUP2, RTC_TAMP1, RTC_TS, RTC_OUT. |
| 8 | PC14-OSC32_IN | bidirectional | Standard 3.3 V (TC) I/O; default function PC14; becomes OSC32_IN only when the LSE oscillator is on (LSEON bit in RCC_CSR), otherwise usable as GPIO. |
| 9 | PC15-OSC32_OUT | bidirectional | Standard 3.3 V (TC) I/O; default function PC15; becomes OSC32_OUT only when the LSE oscillator is on (LSEON bit in RCC_CSR), otherwise usable as GPIO. |
| 10 | PF0 | bidirectional | 5 V tolerant (FT) I/O; default function PF0; EVENTOUT is the only alternate function listed. |
| 11 | PF1 | bidirectional | 5 V tolerant (FT) I/O; default function PF1; EVENTOUT is the only alternate function listed. |
| 12 | PF2 | bidirectional | 5 V tolerant (FT) I/O; default function PF2; EVENTOUT is the only alternate function listed. |
| 13 | PF3 | bidirectional | 5 V tolerant (FT) I/O; default function PF3; EVENTOUT is the only alternate function listed. |
| 14 | PF4 | bidirectional | 5 V tolerant (FT) I/O; default function PF4; EVENTOUT is the only alternate function listed. |
| 15 | PF5 | bidirectional | 5 V tolerant (FT) I/O; default function PF5; EVENTOUT is the only alternate function listed. |
| 16 | VSS_5 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 17 | VDD_5 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 18 | PF6 | bidirectional | 5 V tolerant (FT) I/O; default function PF6; alternate functions TIM5_CH1, TIM5_ETR; additional function ADC_IN27. |
| 19 | PF7 | bidirectional | 5 V tolerant (FT) I/O; default function PF7; alternate function TIM5_CH2; additional functions ADC_IN28, COMP1_INP. |
| 20 | PF8 | bidirectional | 5 V tolerant (FT) I/O; default function PF8; alternate function TIM5_CH3; additional functions ADC_IN29, COMP1_INP. |
| 21 | PF9 | bidirectional | 5 V tolerant (FT) I/O; default function PF9; alternate function TIM5_CH4; additional functions ADC_IN30, COMP1_INP. |
| 22 | PF10 | bidirectional | 5 V tolerant (FT) I/O; default function PF10; additional functions ADC_IN31, COMP1_INP; EVENTOUT is the only alternate function listed. |
| 23 | PH0-OSC_IN | bidirectional | Standard 3.3 V (TC) I/O; default function PH0; becomes OSC_IN only when the HSE oscillator is on (HSEON bit in RCC_CR), otherwise usable as GPIO. |
| 24 | PH1-OSC_OUT | bidirectional | Standard 3.3 V (TC) I/O; default function PH1; becomes OSC_OUT only when the HSE oscillator is on (HSEON bit in RCC_CR), otherwise usable as GPIO. |
| 25 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 26 | PC0 | bidirectional | 5 V tolerant (FT) I/O; default function PC0; alternate functions LCD_SEG18 and TIMx_IC1 (EVENTOUT); additional functions ADC_IN10, COMP1_INP. |
| 27 | PC1 | bidirectional | 5 V tolerant (FT) I/O; default function PC1; alternate functions LCD_SEG19 and TIMx_IC2 (EVENTOUT); additional functions ADC_IN11, COMP1_INP. |
| 28 | PC2 | bidirectional | 5 V tolerant (FT) I/O; default function PC2; alternate functions LCD_SEG20 and TIMx_IC3 (EVENTOUT); additional functions ADC_IN12, COMP1_INP. |
| 29 | PC3 | bidirectional | Standard 3.3 V (TC) I/O; default function PC3; alternate functions LCD_SEG21 and TIMx_IC4 (EVENTOUT); additional functions ADC_IN13, COMP1_INP. |
| 30 | VSSA | power_in | Analog ground pin; section 6.1 states all voltages are referenced to VSS. |
| 31 | VREF- | power_in | Negative reference voltage pin for the ADC; footnote 4 of Table 55 requires VSSA or VREF- to be tied to ground. |
| 32 | VREF+ | power_in | Positive ADC/DAC reference voltage input; Table 55 gives a minimum of 1.8 V and it may be grounded if neither the ADC nor the DAC is used. |
| 33 | VDDA | power_in | Analog supply pin; Table 55 specifies VDDA from 1.8 V to 3.6 V. |
| 34 | PA0-WKUP1 | bidirectional | 5 V tolerant (FT) I/O; default function PA0; alternate functions TIM2_CH1_ETR, TIM5_CH1, USART2_CTS; additional functions WKUP1, RTC_TAMP2, ADC_IN0, COMP1_INP. |
| 35 | PA1 | bidirectional | 5 V tolerant (FT) I/O; default function PA1; alternate functions TIM2_CH2, TIM5_CH2, USART2_RTS, LCD_SEG0; additional functions ADC_IN1, COMP1_INP, OPAMP1_VINP. |
| 36 | PA2 | bidirectional | 5 V tolerant (FT) I/O; default function PA2; alternate functions TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX, LCD_SEG1; additional functions ADC_IN2, COMP1_INP, OPAMP1_VINM. |
| 37 | PA3 | bidirectional | Standard 3.3 V (TC) I/O; default function PA3; alternate functions TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX, LCD_SEG2; additional functions ADC_IN3, COMP1_INP, OPAMP1_VOUT. |
| 38 | VSS_4 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 39 | VDD_4 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 40 | PA4 | bidirectional | Standard 3.3 V (TC) I/O; default function PA4; alternate functions SPI1_NSS, SPI3_NSS, I2S3_WS, USART2_CK; additional functions ADC_IN4, DAC_OUT1, COMP1_INP. |
| 41 | PA5 | bidirectional | Standard 3.3 V (TC) I/O; default function PA5; alternate functions TIM2_CH1_ETR, SPI1_SCK; additional functions ADC_IN5, DAC_OUT2, COMP1_INP. |
| 42 | PA6 | bidirectional | 5 V tolerant (FT) I/O; default function PA6; alternate functions TIM3_CH1, TIM10_CH1, SPI1_MISO, LCD_SEG3; additional functions ADC_IN6, COMP1_INP, OPAMP2_VINP. |
| 43 | PA7 | bidirectional | 5 V tolerant (FT) I/O; default function PA7; alternate functions TIM3_CH2, TIM11_CH1, SPI1_MOSI, LCD_SEG4; additional functions ADC_IN7, COMP1_INP, OPAMP2_VINM. |
| 44 | PC4 | bidirectional | 5 V tolerant (FT) I/O; default function PC4; alternate functions LCD_SEG22, TIMx_IC1 (EVENTOUT); additional functions ADC_IN14, COMP1_INP. |
| 45 | PC5 | bidirectional | 5 V tolerant (FT) I/O; default function PC5; alternate functions LCD_SEG23, TIMx_IC2 (EVENTOUT); additional functions ADC_IN15, COMP1_INP. |
| 46 | PB0 | bidirectional | Standard 3.3 V (TC) I/O; default function PB0; alternate functions TIM3_CH3, LCD_SEG5; additional functions ADC_IN8, COMP1_INP, OPAMP2_VOUT, VREF_OUT. |
| 47 | PB1 | bidirectional | 5 V tolerant (FT) I/O; default function PB1; alternate functions TIM3_CH4, LCD_SEG6; additional functions ADC_IN9, COMP1_INP, VREF_OUT. |
| 48 | PB2 | bidirectional | 5 V tolerant (FT) I/O; default function PB2/BOOT1; BOOT1 is listed as an alternate function and ADC_IN0b as an additional function. |
| 49 | PF11 | bidirectional | 5 V tolerant (FT) I/O; default function PF11; additional function ADC_IN1b; EVENTOUT is the only alternate function listed. |
| 50 | PF12 | bidirectional | 5 V tolerant (FT) I/O; default function PF12; additional function ADC_IN2b; EVENTOUT is the only alternate function listed. |
| 51 | VSS_6 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 52 | VDD_6 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 53 | PF13 | bidirectional | 5 V tolerant (FT) I/O; default function PF13; additional function ADC_IN3b; EVENTOUT is the only alternate function listed. |
| 54 | PF14 | bidirectional | 5 V tolerant (FT) I/O; default function PF14; additional function ADC_IN6b; EVENTOUT is the only alternate function listed. |
| 55 | PF15 | bidirectional | 5 V tolerant (FT) I/O; default function PF15; additional function ADC_IN7b; EVENTOUT is the only alternate function listed. |
| 56 | PG0 | bidirectional | 5 V tolerant (FT) I/O; default function PG0; additional function ADC_IN8b; EVENTOUT is the only alternate function listed. |
| 57 | PG1 | bidirectional | 5 V tolerant (FT) I/O; default function PG1; additional function ADC_IN9b; EVENTOUT is the only alternate function listed. |
| 58 | PE7 | bidirectional | Standard 3.3 V (TC) I/O; default function PE7; additional functions ADC_IN22, COMP1_INP; EVENTOUT is the only alternate function listed. |
| 59 | PE8 | bidirectional | Standard 3.3 V (TC) I/O; default function PE8; additional functions ADC_IN23, COMP1_INP; EVENTOUT is the only alternate function listed. |
| 60 | PE9 | bidirectional | Standard 3.3 V (TC) I/O; default function PE9; alternate function TIM2_CH1_ETR; additional functions ADC_IN24, COMP1_INP. |
| 61 | VSS_7 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 62 | VDD_7 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 63 | PE10 | bidirectional | Standard 3.3 V (TC) I/O; default function PE10; alternate function TIM2_CH2; additional functions ADC_IN25, COMP1_INP. |
| 64 | PE11 | bidirectional | 5 V tolerant (FT) I/O; default function PE11; alternate function TIM2_CH3; no additional functions listed. |
| 65 | PE12 | bidirectional | 5 V tolerant (FT) I/O; default function PE12; alternate functions TIM2_CH4, SPI1_NSS. |
| 66 | PE13 | bidirectional | 5 V tolerant (FT) I/O; default function PE13; alternate function SPI1_SCK. |
| 67 | PE14 | bidirectional | 5 V tolerant (FT) I/O; default function PE14; alternate function SPI1_MISO. |
| 68 | PE15 | bidirectional | 5 V tolerant (FT) I/O; default function PE15; alternate function SPI1_MOSI. |
| 69 | PB10 | bidirectional | 5 V tolerant (FT) I/O; default function PB10; alternate functions TIM2_CH3, I2C2_SCL, USART3_TX, LCD_SEG10. |
| 70 | PB11 | bidirectional | 5 V tolerant (FT) I/O; default function PB11; alternate functions TIM2_CH4, I2C2_SDA, USART3_RX, LCD_SEG11. |
| 71 | VSS_1 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 72 | VDD_1 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 73 | PB12 | bidirectional | 5 V tolerant (FT) I/O; default function PB12; alternate functions TIM10_CH1, I2C2_SMBA, SPI2_NSS, I2S2_WS, USART3_CK, LCD_SEG12; additional functions ADC_IN18, COMP1_INP. |
| 74 | PB13 | bidirectional | 5 V tolerant (FT) I/O; default function PB13; alternate functions TIM9_CH1, SPI2_SCK, I2S2_CK, USART3_CTS, LCD_SEG13; additional functions ADC_IN19, COMP1_INP. |
| 75 | PB14 | bidirectional | 5 V tolerant (FT) I/O; default function PB14; alternate functions TIM9_CH2, SPI2_MISO, USART3_RTS, LCD_SEG14; additional functions ADC_IN20, COMP1_INP. |
| 76 | PB15 | bidirectional | 5 V tolerant (FT) I/O; default function PB15; alternate functions TIM11_CH1, SPI2_MOSI, I2S2_SD, LCD_SEG15; additional functions ADC_IN21, COMP1_INP, RTC_REFIN. |
| 77 | PD8 | bidirectional | 5 V tolerant (FT) I/O; default function PD8; alternate functions USART3_TX, LCD_SEG28. |
| 78 | PD9 | bidirectional | 5 V tolerant (FT) I/O; default function PD9; alternate functions USART3_RX, LCD_SEG29. |
| 79 | PD10 | bidirectional | 5 V tolerant (FT) I/O; default function PD10; alternate functions USART3_CK, LCD_SEG30. |
| 80 | PD11 | bidirectional | 5 V tolerant (FT) I/O; default function PD11; alternate functions USART3_CTS, LCD_SEG31. |
| 81 | PD12 | bidirectional | 5 V tolerant (FT) I/O; default function PD12; alternate functions TIM4_CH1, USART3_RTS, LCD_SEG32. |
| 82 | PD13 | bidirectional | 5 V tolerant (FT) I/O; default function PD13; alternate functions TIM4_CH2, LCD_SEG33. |
| 83 | VSS_8 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 84 | VDD_8 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 85 | PD14 | bidirectional | 5 V tolerant (FT) I/O; default function PD14; alternate functions TIM4_CH3, LCD_SEG34. |
| 86 | PD15 | bidirectional | 5 V tolerant (FT) I/O; default function PD15; alternate functions TIM4_CH4, LCD_SEG35. |
| 87 | PG2 | bidirectional | 5 V tolerant (FT) I/O; default function PG2; additional function ADC_IN10b; EVENTOUT is the only alternate function listed. |
| 88 | PG3 | bidirectional | 5 V tolerant (FT) I/O; default function PG3; additional function ADC_IN11b; EVENTOUT is the only alternate function listed. |
| 89 | PG4 | bidirectional | 5 V tolerant (FT) I/O; default function PG4; additional function ADC_IN12b; EVENTOUT is the only alternate function listed. |
| 90 | PG5 | bidirectional | 5 V tolerant (FT) I/O; default function PG5; EVENTOUT is the only alternate function listed. |
| 91 | PG6 | bidirectional | 5 V tolerant (FT) I/O; default function PG6; EVENTOUT is the only alternate function listed. |
| 92 | PG7 | bidirectional | 5 V tolerant (FT) I/O; default function PG7; EVENTOUT is the only alternate function listed. |
| 93 | PG8 | bidirectional | 5 V tolerant (FT) I/O; default function PG8; EVENTOUT is the only alternate function listed. |
| 94 | VSS_9 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 95 | VDD_9 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 96 | PC6 | bidirectional | 5 V tolerant (FT) I/O; default function PC6; alternate functions TIM3_CH1, I2S2_MCK, LCD_SEG24. |
| 97 | PC7 | bidirectional | 5 V tolerant (FT) I/O; default function PC7; alternate functions TIM3_CH2, I2S3_MCK, LCD_SEG25. |
| 98 | PC8 | bidirectional | 5 V tolerant (FT) I/O; default function PC8; alternate functions TIM3_CH3, LCD_SEG26. |
| 99 | PC9 | bidirectional | 5 V tolerant (FT) I/O; default function PC9; alternate functions TIM3_CH4, LCD_SEG27. |
| 100 | PA8 | bidirectional | 5 V tolerant (FT) I/O; default function PA8; alternate functions USART1_CK, MCO, LCD_COM0. |
| 101 | PA9 | bidirectional | 5 V tolerant (FT) I/O; default function PA9; alternate functions USART1_TX, LCD_COM1. |
| 102 | PA10 | bidirectional | 5 V tolerant (FT) I/O; default function PA10; alternate functions USART1_RX, LCD_COM2. |
| 103 | PA11 | bidirectional | 5 V tolerant (FT) I/O; default function PA11; alternate functions USART1_CTS, SPI1_MISO; additional function USB_DM. |
| 104 | PA12 | bidirectional | 5 V tolerant (FT) I/O; default function PA12; alternate functions USART1_RTS, SPI1_MOSI; additional function USB_DP. |
| 105 | PA13 | bidirectional | 5 V tolerant (FT) I/O; default function JTMS-SWDIO; JTMS-SWDIO is the SWJ debug data pin. |
| 106 | PH2 | bidirectional | 5 V tolerant (FT) I/O; default function PH2; no alternate or additional functions listed. |
| 107 | VSS_2 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 108 | VDD_2 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 109 | PA14 | bidirectional | 5 V tolerant (FT) I/O; default function JTCK-SWCLK; JTCK-SWCLK is the SWJ debug clock pin. |
| 110 | PA15 | bidirectional | 5 V tolerant (FT) I/O; default function JTDI; alternate functions TIM2_CH1_ETR, SPI1_NSS, SPI3_NSS, I2S3_WS, LCD_SEG17. |
| 111 | PC10 | bidirectional | 5 V tolerant (FT) I/O; default function PC10; alternate functions SPI3_SCK, I2S3_CK, USART3_TX, UART4_TX, LCD_SEG28, LCD_SEG40, LCD_COM4. |
| 112 | PC11 | bidirectional | 5 V tolerant (FT) I/O; default function PC11; alternate functions SPI3_MISO, USART3_RX, UART4_RX, LCD_SEG29, LCD_SEG41, LCD_COM5. |
| 113 | PC12 | bidirectional | 5 V tolerant (FT) I/O; default function PC12; alternate functions SPI3_MOSI, I2S3_SD, USART3_CK, UART5_TX, LCD_SEG30, LCD_SEG42, LCD_COM6. |
| 114 | PD0 | bidirectional | 5 V tolerant (FT) I/O; default function PD0; alternate functions TIM9_CH1, SPI2_NSS, I2S2_WS. |
| 115 | PD1 | bidirectional | 5 V tolerant (FT) I/O; default function PD1; alternate functions SPI2_SCK, I2S2_CK. |
| 116 | PD2 | bidirectional | 5 V tolerant (FT) I/O; default function PD2; alternate functions TIM3_ETR, UART5_RX, LCD_SEG31, LCD_SEG43, LCD_COM7. |
| 117 | PD3 | bidirectional | 5 V tolerant (FT) I/O; default function PD3; alternate functions SPI2_MISO, USART2_CTS. |
| 118 | PD4 | bidirectional | 5 V tolerant (FT) I/O; default function PD4; alternate functions SPI2_MOSI, I2S2_SD, USART2_RTS. |
| 119 | PD5 | bidirectional | 5 V tolerant (FT) I/O; default function PD5; alternate function USART2_TX. |
| 120 | VSS_10 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 121 | VDD_10 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 122 | PD6 | bidirectional | 5 V tolerant (FT) I/O; default function PD6; alternate function USART2_RX. |
| 123 | PD7 | bidirectional | 5 V tolerant (FT) I/O; default function PD7; alternate functions TIM9_CH2, USART2_CK. |
| 124 | PG9 | bidirectional | 5 V tolerant (FT) I/O; default function PG9; EVENTOUT is the only alternate function listed. |
| 125 | PG10 | bidirectional | 5 V tolerant (FT) I/O; default function PG10; EVENTOUT is the only alternate function listed. |
| 126 | PG11 | bidirectional | 5 V tolerant (FT) I/O; default function PG11; EVENTOUT is the only alternate function listed. |
| 127 | PG12 | bidirectional | 5 V tolerant (FT) I/O; default function PG12; EVENTOUT is the only alternate function listed. |
| 128 | PG13 | bidirectional | 5 V tolerant (FT) I/O; default function PG13; EVENTOUT is the only alternate function listed. |
| 129 | PG14 | bidirectional | 5 V tolerant (FT) I/O; default function PG14; EVENTOUT is the only alternate function listed. |
| 130 | VSS_11 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 131 | VDD_11 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
| 132 | PG15 | bidirectional | 5 V tolerant (FT) I/O; default function PG15; EVENTOUT is the only alternate function listed. |
| 133 | PB3 | bidirectional | 5 V tolerant (FT) I/O; default function JTDO; alternate functions TIM2_CH2, SPI1_SCK, SPI3_SCK, I2S3_CK, LCD_SEG7; additional function COMP2_INM. |
| 134 | PB4 | bidirectional | 5 V tolerant (FT) I/O; default function NJTRST; alternate functions TIM3_CH1, SPI1_MISO, SPI3_MISO, LCD_SEG8, NJTRST; additional function COMP2_INP. |
| 135 | PB5 | bidirectional | 5 V tolerant (FT) I/O; default function PB5; alternate functions TIM3_CH2, I2C1_SMBA, SPI1_MOSI, SPI3_MOSI, I2S3_SD, LCD_SEG9; additional function COMP2_INP. |
| 136 | PB6 | bidirectional | 5 V tolerant (FT) I/O; default function PB6; alternate functions TIM4_CH1, I2C1_SCL, USART1_TX; additional function COMP2_INP. |
| 137 | PB7 | bidirectional | 5 V tolerant (FT) I/O; default function PB7; alternate functions TIM4_CH2, I2C1_SDA, USART1_RX; additional functions COMP2_INP, PVD_IN. |
| 138 | BOOT0 | input | Dedicated BOOT0 input pin (type B in Table 7 legend). |
| 139 | PB8 | bidirectional | 5 V tolerant (FT) I/O; default function PB8; alternate functions TIM4_CH3, TIM10_CH1, I2C1_SCL, LCD_SEG16. |
| 140 | PB9 | bidirectional | 5 V tolerant (FT) I/O; default function PB9; alternate functions TIM4_CH4, TIM11_CH1, I2C1_SDA, LCD_COM3. |
| 141 | PE0 | bidirectional | 5 V tolerant (FT) I/O; default function PE0; alternate functions TIM4_ETR, TIM10_CH1, LCD_SEG36. |
| 142 | PE1 | bidirectional | 5 V tolerant (FT) I/O; default function PE1; alternate functions TIM11_CH1, LCD_SEG37. |
| 143 | VSS_3 | power_in | Ground pin; all voltages are referenced to VSS per section 6.1. |
| 144 | VDD_3 | power_in | Digital supply pin; device supply range is 1.65 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-144(20x20) |
| Category | Embedded Processors & Controllers |
| Pins | 144 |
CAD (KiCad official)
- Symbol:
STM32L151ZET6 - Footprint:
Package_QFP:LQFP-144_20x20mm_P0.5mm - 3D model: LQFP-144(20x20) (KiCad packages3D, STEP)
- 3D model files:
stm32l151zet6-etched.step/stm32l151zet6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32l151zet6.step/stm32l151zet6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (136 pp, sha256
6ba5d188efc840bc, retrieved 2026-10-08, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).