Generated by kicad-footprint-generator · KiCad file format 20260206
STM32G041F8P6
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · TSSOP-20
STM32G041F8P6 from STMicroelectronics, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PB7/PB8 | bidirectional | 5 V-tolerant Fm+-capable I/O bonded as PB7 (FT_fa; USART1_RX, I2C1_SDA, PVD_IN, ADC_IN11) or PB8 (FT_f; SPI2_SCK, TIM16_CH1, I2C1_SCL) depending on the variant. |
| 2 | PB9/PC14-OSC32_IN | bidirectional | Pin 2 is bonded as PB9 (5 V-tolerant Fm+-capable I/O; IR_OUT, TIM17_CH1, SPI2_NSS, I2C1_SDA) or as PC14 (5 V-tolerant GPIO supplied through the RTC power switch, limited to 3 mA sink, and usable as OSC32_IN), and PC14 output use is limited to 2 MHz at 30 pF and must not source LED current. |
| 3 | PC15-OSC32_OUT | bidirectional | 5 V-tolerant GPIO supplied through the RTC power switch (3 mA limit) that serves as the LSE OSC32_OUT output; in output mode it must not exceed 2 MHz at 30 pF and must not be used as a current source. |
| 4 | VDD/VDDA | power_in | Main supply pin for VDD (1.7 V to 3.6 V) that also supplies VDDIO1 and the analog domain, with VDDA at 1.62 V minimum for the ADC and 2.4 V minimum for VREFBUF. |
| 5 | VSS/VSSA | power_in | Ground pin; all device voltages are referenced to VSS and it must be connected to the external ground. |
| 6 | PF2-NRST | bidirectional | Active-low reset pin with embedded weak pull-up (25 to 55 kΩ) whose input low level is up to 0.3 × VDDIO1 and whose input pulses shorter than 70 ns are filtered. |
| 7 | PA0 | bidirectional | 5 V-tolerant analog-capable I/O (FT_a) with ADC_IN0, TAMP_IN2 and WKUP1 functions, alternates SPI2_SCK, USART2_CTS, TIM2_CH1_ETR and LPTIM1_OUT. |
| 8 | PA1 | bidirectional | 5 V-tolerant analog-capable I/O (FT_ea) with ADC_IN1 and a switchable diode to VDD, alternates SPI1_SCK/I2S1_CK, USART2_RTS_DE_CK, TIM2_CH2, I2C1_SMBA and EVENTOUT. |
| 9 | PA2 | bidirectional | 5 V-tolerant analog-capable I/O (FT_a) with ADC_IN2, WKUP4 and LSCO functions, alternates SPI1_MOSI/I2S1_SD, USART2_TX, TIM2_CH3 and LPUART1_TX. |
| 10 | PA3 | bidirectional | 5 V-tolerant analog-capable I/O (FT_ea) with ADC_IN3, alternates SPI2_MISO, USART2_RX, TIM2_CH4, LPUART1_RX and EVENTOUT. |
| 11 | PA4 | bidirectional | 5 V-tolerant analog-capable I/O (FT_a) with ADC_IN4, TAMP_IN1, RTC_TS, RTC_OUT1 and WKUP2 functions, alternates SPI1_NSS/I2S1_WS, SPI2_MOSI, TIM14_CH1 and LPTIM2_OUT. |
| 12 | PA5 | bidirectional | 5 V-tolerant analog-capable I/O (FT_ea) with ADC_IN5, alternates SPI1_SCK/I2S1_CK, TIM2_CH1_ETR, LPTIM2_ETR and EVENTOUT. |
| 13 | PA6 | bidirectional | 5 V-tolerant analog-capable I/O (FT_ea) with ADC_IN6, alternates SPI1_MISO/I2S1_MCK, TIM3_CH1, TIM1_BKIN, TIM16_CH1 and LPUART1_CTS. |
| 14 | PA7 | bidirectional | 5 V-tolerant analog-capable I/O (FT_a) with ADC_IN7, alternates SPI1_MOSI/I2S1_SD, TIM3_CH2, TIM1_CH1N, TIM14_CH1 and TIM17_CH1. |
| 15 | PB0/PB1/PB2/PA8 | bidirectional | Pin 15 is bonded as PB0 (FT_ea, ADC_IN8), PB1 (FT_ea, ADC_IN9), PB2 (FT_ea, ADC_IN10) or PA8 (5 V-tolerant GPIO with MCO, SPI2_NSS, TIM1_CH1, LPTIM2_OUT alternates) depending on the variant. |
| 16 | PA11 [PA9] | bidirectional | 5 V-tolerant Fm+-capable analog I/O (FT_fa, ADC_IN15) that is PA11 by default (SPI1_MISO/I2S1_MCK, USART1_CTS, TIM1_CH4, I2C2_SCL) and can be remapped to PA9 through SYSCFG_CFGR1. |
| 17 | PA12 [PA10] | bidirectional | 5 V-tolerant Fm+-capable analog I/O (FT_fa, ADC_IN16) that is PA12 by default (SPI1_MOSI/I2S1_SD, USART1_RTS_DE_CK, TIM1_ETR, I2C2_SDA) and can be remapped to PA10 through SYSCFG_CFGR1. |
| 18 | PA13 | bidirectional | 5 V-tolerant analog-capable I/O (FT_ea, ADC_IN17) that is configured as SWDIO after reset with the internal pull-up activated, with alternates IR_OUT and EVENTOUT. |
| 19 | PA15/PA14-BOOT0 | bidirectional | Pin 19 is bonded as PA14-BOOT0 (FT_a, ADC_IN18; SWCLK after reset with internal pull-down, and BOOT0 boot-mode pin) or as PA15 (5 V-tolerant GPIO; SPI1_NSS/I2S1_WS, USART2_RX, TIM2_CH1_ETR) depending on the variant. |
| 20 | PB3/PB4/PB5/PB6 | bidirectional | 5 V-tolerant I/O bonded as PB3 (SPI1_SCK/I2S1_CK, TIM1_CH2, TIM2_CH2), PB4 (SPI1_MISO/I2S1_MCK, TIM3_CH1, USART1_CTS), PB5 (WKUP6, SPI1_MOSI/I2S1_SD, TIM3_CH2, I2C1_SMBA) or PB6 (FT_f Fm+-capable; USART1_TX, TIM1_CH3, I2C1_SCL) depending on the variant. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-20 |
| Category | Embedded Processors & Controllers |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External supply voltage | VDD | -0.3 | 4 | V | 46 | ||
| External supply voltage on VBAT pin | VBAT | -0.3 | 4 | V | 46 | ||
| External voltage on VREF+ pin | VREF+ | -0.3 | V | Max printed as Min(VDD + 0.4, 4.0) | 46 | ||
| Input voltage on FT_xx | VIN | -0.3 | V | Max printed as VDD + 4.0; see note 2 (pull-up/pull-down must be disabled above 4 V) | 46 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 46 | ||
| Current into VDD/VDDA power pin (source) | IVDD/VDDA | 100 | mA | 46 | |||
| Output current sunk by any I/O and control pin except FT_f | IIO(PIN) | 15 | mA | 46 | |||
| Output current sunk by any FT_f pin | IIO(PIN) | 20 | mA | 46 | |||
| Output current sourced by any I/O and control pin | IIO(PIN) | 15 | mA | 46 | |||
| Total output current sunk by sum of all I/Os and control pins | ∑IIO(PIN) | 80 | mA | 46 | |||
| Total output current sourced by sum of all I/Os and control pins | ∑IIO(PIN) | 80 | mA | 46 | |||
| Injected current on a FT_xx pin | IINJ(PIN) | -5 | mA | Max printed as NA | 46 | ||
| Total injected current (sum of all I/Os and control pins) | ∑/IINJ(PIN)/ | 25 | mA | 46 | |||
| Storage temperature range | TSTG | -65 | 150 | °C | 47 | ||
| Maximum junction temperature | TJ | 150 | °C | 47 | |||
| Internal AHB clock frequency | fHCLK | 0 | 64 | MHz | 47 | ||
| Internal APB clock frequency | fPCLK | 0 | 64 | MHz | 47 | ||
| Standard operating voltage | VDD | 1.7 | 3.6 | V | Standard operating voltage | 47 | |
| Analog supply voltage | VDDA | 1.62 | 3.6 | V | For ADC operation | 47 | |
| Analog supply voltage | VDDA | 2.4 | 3.6 | V | For VREFBUF operation | 47 | |
| Backup operating voltage | VBAT | 1.55 | 3.6 | V | 47 | ||
| I/O input voltage | VIN | -0.3 | V | Max printed as Min(VDD + 3.6, 5.5) | 47 | ||
| Ambient temperature | TA | -40 | 85 | °C | Suffix 6 | 47 | |
| Junction temperature | TJ | -40 | 105 | °C | Suffix 6 | 47 | |
| VDD slew rate | tVDD | 10 | µs/V | VDD falling; ULPEN = 0; max printed as ∞ | 48 | ||
| VDD slew rate | tVDD | 100 | ms/V | VDD falling; ULPEN = 1; max printed as ∞ | 48 | ||
| POR temporization when VDD crosses VPOR | tRSTTEMPO | 250 | 400 | µs | VDD rising | 48 | |
| Power-on reset threshold | VPOR | 1.62 | 1.66 | 1.7 | V | 48 | |
| Power-down reset threshold | VPDR | 1.6 | 1.64 | 1.69 | V | 48 | |
| Brownout reset threshold 1 | VBOR1 | 2.05 | 2.1 | 2.18 | V | VDD rising | 48 |
| Brownout reset threshold 1 | VBOR1 | 1.95 | 2 | 2.08 | V | VDD falling | 48 |
| Brownout reset threshold 2 | VBOR2 | 2.2 | 2.31 | 2.38 | V | VDD rising | 48 |
| Brownout reset threshold 2 | VBOR2 | 2.1 | 2.21 | 2.28 | V | VDD falling | 48 |
| Brownout reset threshold 3 | VBOR3 | 2.5 | 2.62 | 2.68 | V | VDD rising | 48 |
| Brownout reset threshold 3 | VBOR3 | 2.4 | 2.52 | 2.58 | V | VDD falling | 48 |
| Brownout reset threshold 4 | VBOR4 | 2.8 | 2.91 | 3 | V | VDD rising | 49 |
| Brownout reset threshold 4 | VBOR4 | 2.7 | 2.81 | 2.9 | V | VDD falling | 49 |
| Internal reference voltage | VREFINT | 1.182 | 1.212 | 1.232 | V | -40°C < TJ < 130°C | 49 |
| Start time of reference voltage buffer when ADC is enabled | tstart_vrefint | 8 | 12 | µs | 49 | ||
| VREFINT buffer consumption from VDD when converted by ADC | IDD(VREFINTBUF) | 12.5 | 20 | µA | 49 | ||
| Internal reference voltage spread over the temperature range | ∆VREFINT | 5 | 7.5 | mV | VDD = 3 V | 49 | |
| Temperature coefficient | TCoeff_vrefint | 30 | 50 | ppm/°C | 49 | ||
| Long term stability | ACoeff | 300 | 1000 | ppm | 1000 hours, T = 25 °C | 49 | |
| Voltage coefficient | VDDCoeff | 250 | 1200 | ppm/V | 3.0 V < VDD < 3.6 V | 49 | |
| Supply current in Run mode | IDD(Run) | 5.2 | 6.7 | mA | Range 1; PLL enabled; fHCLK = fPLLRCLK; 64 MHz; Flash memory; 25 °C | 51 | |
| Supply current in Sleep mode | IDD(Sleep) | 1.3 | 1.8 | mA | Range 1; Flash enabled; fHCLK = fPLLRCLK 64 MHz; all peripherals disabled; 25 °C | 53 | |
| Supply current in Stop 0 mode | IDD(Stop 0) | 270 | 345 | µA | HSI kernel enabled; VDD 3 V; 25 °C | 53 | |
| Supply current in Stop 0 mode | IDD(Stop 0) | 97 | 125 | µA | HSI kernel disabled; VDD 3 V; 25 °C | 53 | |
| Supply current in Standby mode | IDD(Standby) | 0.2 | 0.9 | µA | RTC disabled; VDD 3.0 V; 25 °C | 54 | |
| Supply current in Shutdown mode | IDD(Shutdown) | 25 | 800 | nA | RTC disabled; VDD 3.0 V; 25 °C | 55 | |
| Wakeup time from Standby mode | tWUSTBY | 14.5 | 30 | µs | Transiting to Run mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 | 59 | |
| Wakeup time from Shutdown mode | tWUSHDN | 258 | 340 | µs | Transiting to Run mode; HCLK = HSI16 = 16 MHz; Regulator in Range 1 | 59 | |
| User external clock source frequency | fHSE_ext | 8 | 48 | MHz | Voltage scaling Range 1 | 60 | |
| Oscillator frequency | fOSC_IN | 4 | 8 | 48 | MHz | 61 | |
| HSE current consumption during startup | IDD(HSE) | 5.5 | mA | During startup | 62 | ||
| HSI16 Frequency | fHSI16 | 15.88 | 16.08 | MHz | VDD=3.0 V, TA=30 °C | 64 | |
| LSI frequency | fLSI | 29.5 | 34 | kHz | VDD = 1.62 V to 3.6 V, TA = -40 to 125 °C | 65 | |
| PLL input clock frequency | fPLL_IN | 2.66 | 16 | MHz | 66 | ||
| PLL lock time | tLOCK | 15 | 40 | µs | 66 | ||
| 64-bit programming time | tprog | 85 | 125 | µs | 66 |
CAD (KiCad official)
- Symbol:
STM32G041F8P6 - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
stm32g041f8p6-etched.step/stm32g041f8p6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32g041f8p6.step/stm32g041f8p6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (118 pp, sha256
586607fd294bd34f, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).