3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F745ZGT6
STMicroelectronics · ST Microelectronics · LQFP-144(20x20)
STM32F745ZGT6 from STMicroelectronics, in a LQFP-144(20x20). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PE2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACECLK, SPI4_SCK, SAI1_MCLK_A, QUADSPI_BK1_IO2, ETH_MII_TXD3 and FMC_A23. |
| 2 | PE3 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED0, SAI1_SD_B and FMC_A19. |
| 3 | PE4 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED1, SPI4_NSS, SAI1_FS_A, FMC_A20, DCMI_D4 and LCD_B0. |
| 4 | PE5 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED2, TIM9_CH1, SPI4_MISO, SAI1_SCK_A, FMC_A21, DCMI_D6 and LCD_G0. |
| 5 | PE6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED3, TIM1_BKIN2, TIM9_CH2, SPI4_MOSI, SAI1_SD_A, SAI2_MCK_B, FMC_A22, DCMI_D7 and LCD_G1. |
| 6 | VBAT | power_in | Backup supply for the RTC, backup registers and backup SRAM, operating from 1.65 V to 3.6 V. |
| 7 | PC13 | bidirectional | Power-switched GPIO whose supply switch sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source LED-type current; additional functions RTC_TAMP1, RTC_TS, RTC_OUT and WKUP4. |
| 8 | PC14 | bidirectional | Power-switched GPIO (3 mA switch limit, 2 MHz / 30 pF output limit) that doubles as the LSE oscillator input OSC32_IN; FT except in oscillator mode. |
| 9 | PC15 | bidirectional | Power-switched GPIO (3 mA switch limit, 2 MHz / 30 pF output limit) that doubles as the LSE oscillator output OSC32_OUT; FT except in oscillator mode. |
| 10 | PF0 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C2_SDA and FMC_A0. |
| 11 | PF1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C2_SCL and FMC_A1. |
| 12 | PF2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C2_SMBA and FMC_A2. |
| 13 | PF3 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A3 and ADC3_IN9 analog input. |
| 14 | PF4 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A4 and ADC3_IN14 analog input. |
| 15 | PF5 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A5 and ADC3_IN15 analog input. |
| 16 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 17 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 18 | PF6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM10_CH1, SPI5_NSS, SAI1_SD_B, UART7_Rx and QUADSPI_BK1_IO3, and ADC3_IN4 analog input. |
| 19 | PF7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM11_CH1, SPI5_SCK, SAI1_MCLK_B, UART7_Tx and QUADSPI_BK1_IO2, and ADC3_IN5 analog input. |
| 20 | PF8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI5_MISO, SAI1_SCK_B, UART7_RTS, TIM13_CH1 and QUADSPI_BK1_IO0, and ADC3_IN6 analog input. |
| 21 | PF9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI5_MOSI, SAI1_FS_B, UART7_CTS, TIM14_CH1 and QUADSPI_BK1_IO1, and ADC3_IN7 analog input. |
| 22 | PF10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions DCMI_D11 and LCD_DE, and ADC3_IN8 analog input. |
| 23 | PH0 | bidirectional | HSE oscillator input OSC_IN (also GPIO PH0); FT except when used in oscillator mode. |
| 24 | PH1 | bidirectional | HSE oscillator output OSC_OUT (also GPIO PH1); FT except when used in oscillator mode. |
| 25 | NRST | bidirectional | Active-low bidirectional reset pin with weak pull-up; input range -0.3 V to 5.5 V for 2 V <= VDD <= 3.6 V. |
| 26 | PC0 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SAI2_FS_B, OTG_HS_ULPI_STP, FMC_SDNWE and LCD_R5, and ADC123_IN10 analog input. |
| 27 | PC1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED0, SPI2_MOSI/I2S2_SD, SAI1_SD_A and ETH_MDC, plus ADC123_IN11, RTC_TAMP3 and WKUP3. |
| 28 | PC2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI2_MISO, OTG_HS_ULPI_DIR, ETH_MII_TXD2 and FMC_SDNE0, and ADC123_IN12 analog input. |
| 29 | PC3 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI2_MOSI/I2S2_SD, OTG_HS_ULPI_NXT, ETH_MII_TX_CLK and FMC_SDCKE0, and ADC123_IN13 analog input. |
| 30 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 31 | VSSA | power_in | Analog ground reference; must be tied to VSS (VSSA = VSS). |
| 32 | VREF+ | power_in | Positive reference voltage for the ADC and DAC; when present, VDDA - VREF+ must be below 1.2 V. |
| 33 | VDDA | power_in | Analog supply: 1.7 V to 2.4 V when ADC is limited to 1.2 Msps, or 2.4 V to 3.6 V for 2.4 Msps; must be at the same potential as VDD. |
| 34 | PA0 | bidirectional | FT GPIO and WKUP1 wake-up input with alternate functions TIM2_CH1/TIM2_ETR, TIM5_CH1, TIM8_ETR, USART2_CTS, UART4_TX, SAI2_SD_B and ETH_MII_CRS, plus ADC123_IN0 analog input. |
| 35 | PA1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM2_CH2, TIM5_CH2, USART2_RTS, UART4_RX, QUADSPI_BK1_IO3, SAI2_MCK_B and LCD_R2, and ADC123_IN1 analog input. |
| 36 | PA2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM2_CH3, TIM5_CH3, TIM9_CH1, USART2_TX, SAI2_SCK_B, ETH_MDIO and LCD_R1, plus ADC123_IN2 and WKUP2. |
| 37 | PA3 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM2_CH4, TIM5_CH4, TIM9_CH2, USART2_RX, OTG_HS_ULPI_D0, ETH_MII_COL and LCD_B5, and ADC123_IN3 analog input. |
| 38 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 39 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 40 | PA4 | bidirectional | 3.3 V tolerant TTa I/O connected directly to the ADC, with alternate functions SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, USART2_CK, OTG_HS_SOF, DCMI_HSYNC and LCD_VSYNC, plus ADC12_IN4 and DAC_OUT1. |
| 41 | PA5 | bidirectional | 3.3 V tolerant TTa I/O connected directly to the ADC, with alternate functions TIM2_CH1/TIM2_ETR, TIM8_CH1N, SPI1_SCK/I2S1_CK, OTG_HS_ULPI_CK and LCD_R4, plus ADC12_IN5 and DAC_OUT2. |
| 42 | PA6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO, TIM13_CH1, DCMI_PIXCLK and LCD_G2, and ADC12_IN6 analog input. |
| 43 | PA7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH1N, TIM3_CH2, TIM8_CH1N, SPI1_MOSI/I2S1_SD, TIM14_CH1, ETH_MII_RX_DV/ETH_RMII_CRS_DV and FMC_SDNWE, and ADC12_IN7 analog input. |
| 44 | PC4 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2S1_MCK, SPDIFRX_IN2, ETH_MII_RXD0/ETH_RMII_RXD0 and FMC_SDNE0, and ADC12_IN14 analog input. |
| 45 | PC5 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPDIFRX_IN3, ETH_MII_RXD1/ETH_RMII_RXD1 and FMC_SDCKE0, and ADC12_IN15 analog input. |
| 46 | PB0 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH2N, TIM3_CH3, TIM8_CH2N, UART4_CTS, LCD_R3, OTG_HS_ULPI_D1 and ETH_MII_RXD2, and ADC12_IN8 analog input. |
| 47 | PB1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH3N, TIM3_CH4, TIM8_CH3N, LCD_R6, OTG_HS_ULPI_D2 and ETH_MII_RXD3, and ADC12_IN9 analog input. |
| 48 | PB2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SAI1_SD_A, SPI3_MOSI/I2S3_SD and QUADSPI_CLK. |
| 49 | PF11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI5_MOSI, SAI2_SD_B, FMC_SDNRAS and DCMI_D12. |
| 50 | PF12 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A6. |
| 51 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 52 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 53 | PF13 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C4_SMBA and FMC_A7. |
| 54 | PF14 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C4_SCL and FMC_A8. |
| 55 | PF15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C4_SDA and FMC_A9. |
| 56 | PG0 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A10. |
| 57 | PG1 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A11. |
| 58 | PE7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_ETR, UART7_Rx, QUADSPI_BK2_IO0 and FMC_D4. |
| 59 | PE8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH1N, UART7_Tx, QUADSPI_BK2_IO1 and FMC_D5. |
| 60 | PE9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH1, UART7_RTS, QUADSPI_BK2_IO2 and FMC_D6. |
| 61 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 62 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 63 | PE10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH2N, UART7_CTS, QUADSPI_BK2_IO3 and FMC_D7. |
| 64 | PE11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH2, SPI4_NSS, SAI2_SD_B, FMC_D8 and LCD_G3. |
| 65 | PE12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH3N, SPI4_SCK, SAI2_SCK_B, FMC_D9 and LCD_B4. |
| 66 | PE13 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH3, SPI4_MISO, SAI2_FS_B, FMC_D10 and LCD_DE. |
| 67 | PE14 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH4, SPI4_MOSI, SAI2_MCK_B, FMC_D11 and LCD_CLK. |
| 68 | PE15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_BKIN, FMC_D12 and LCD_R7. |
| 69 | PB10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM2_CH3, I2C2_SCL, SPI2_SCK/I2S2_CK, USART3_TX, OTG_HS_ULPI_D3, ETH_MII_RX_ER and LCD_G4. |
| 70 | PB11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM2_CH4, I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_MII_TX_EN/ETH_RMII_TX_EN and LCD_G5. |
| 71 | VCAP_1 | power_in | Voltage regulator output for the 1.2 V core domain; requires an external 2.2 µF CEXT with ESR below 2 Ω (Table 20). |
| 72 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 73 | PB12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_BKIN, I2C2_SMBA, SPI2_NSS/I2S2_WS, USART3_CK, CAN2_RX, OTG_HS_ULPI_D5, ETH_MII_TXD0/ETH_RMII_TXD0 and OTG_HS_ID. |
| 74 | PB13 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH1N, SPI2_SCK/I2S2_CK, USART3_CTS, CAN2_TX, OTG_HS_ULPI_D6 and ETH_MII_TXD1/ETH_RMII_TXD1, plus OTG_HS_VBUS. |
| 75 | PB14 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH2N, TIM8_CH2N, SPI2_MISO, USART3_RTS, TIM12_CH1 and OTG_HS_DM. |
| 76 | PB15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions RTC_REFIN, TIM1_CH3N, TIM8_CH3N, SPI2_MOSI/I2S2_SD, TIM12_CH2 and OTG_HS_DP. |
| 77 | PD8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART3_TX, SPDIFRX_IN11 and FMC_D13. |
| 78 | PD9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART3_RX and FMC_D14. |
| 79 | PD10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART3_CK, FMC_D15 and LCD_B3. |
| 80 | PD11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions I2C4_SMBA, USART3_CTS, QUADSPI_BK1_IO0, SAI2_SD_A and FMC_A16/FMC_CLE. |
| 81 | PD12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH1, LPTIM1_IN1, I2C4_SCL, USART3_RTS, QUADSPI_BK1_IO1, SAI2_FS_A and FMC_A17/FMC_ALE. |
| 82 | PD13 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH2, LPTIM1_OUT, I2C4_SDA, QUADSPI_BK1_IO3, SAI2_SCK_A and FMC_A18. |
| 83 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 84 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 85 | PD14 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH3, UART8_CTS and FMC_D0. |
| 86 | PD15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH4, UART8_RTS and FMC_D1. |
| 87 | PG2 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A12. |
| 88 | PG3 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A13. |
| 89 | PG4 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A14/FMC_BA0. |
| 90 | PG5 | bidirectional | 5 V tolerant (FT) GPIO with alternate function FMC_A15/FMC_BA1. |
| 91 | PG6 | bidirectional | 5 V tolerant (FT) GPIO with additional functions DCMI_D12 and LCD_R7. |
| 92 | PG7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART6_CK, FMC_INT, DCMI_D13 and LCD_CLK. |
| 93 | PG8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI6_NSS, SPDIFRX_IN2, USART6_RTS, ETH_PPS_OUT and FMC_SDCLK. |
| 94 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 95 | VDDUSB | power_in | USB supply for PA11, PA12, PB14 and PB15: 1.7 V to 3.6 V when USB is not used, and 3.0 V to 3.6 V when USB is used. |
| 96 | PC6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM3_CH1, TIM8_CH1, I2S2_MCK, USART6_TX, SDMMC1_D6, DCMI_D0 and LCD_HSYNC. |
| 97 | PC7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM3_CH2, TIM8_CH2, I2S3_MCK, USART6_RX, SDMMC1_D7, DCMI_D1 and LCD_G6. |
| 98 | PC8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED1, TIM3_CH3, TIM8_CH3, UART5_RTS, USART6_CK, SDMMC1_D0 and DCMI_D2. |
| 99 | PC9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions MCO2, TIM3_CH4, TIM8_CH4, I2C3_SDA, I2S_CKIN, UART5_CTS, QUADSPI_BK1_IO0, SDMMC1_D1 and DCMI_D3. |
| 100 | PA8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions MCO1, TIM1_CH1, TIM8_BKIN2, I2C3_SCL, USART1_CK, OTG_FS_SOF and LCD_R6. |
| 101 | PA9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH2, I2C3_SMBA, SPI2_SCK/I2S2_CK, USART1_TX and DCMI_D0, plus OTG_FS_VBUS. |
| 102 | PA10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH3, USART1_RX, OTG_FS_ID and DCMI_D1. |
| 103 | PA11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_CH4, USART1_CTS, CAN1_RX, OTG_FS_DM and LCD_R4; USB supply pin VDDUSB applies. |
| 104 | PA12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM1_ETR, USART1_RTS, SAI2_FS_B, CAN1_TX, OTG_FS_DP and LCD_R5; USB supply pin VDDUSB applies. |
| 105 | PA13 | bidirectional | 5 V tolerant (FT) GPIO and JTAG/SWD pin JTMS-SWDIO for debug. |
| 106 | VCAP_2 | power_in | Voltage regulator output for the 1.2 V core domain; requires an external 2.2 µF CEXT with ESR below 2 Ω (Table 20). |
| 107 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 108 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 109 | PA14 | bidirectional | 5 V tolerant (FT) GPIO and JTAG/SWD clock pin JTCK-SWCLK for debug. |
| 110 | PA15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions JTDI, TIM2_CH1/TIM2_ETR, HDMI-CEC, SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS and UART4_RTS. |
| 111 | PC10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI3_SCK/I2S3_CK, USART3_TX, UART4_TX, QUADSPI_BK1_IO1, SDMMC1_D2, DCMI_D8 and LCD_R2. |
| 112 | PC11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI3_MISO, USART3_RX, UART4_RX, QUADSPI_BK2_NCS, SDMMC1_D3 and DCMI_D4. |
| 113 | PC12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED3, SPI3_MOSI/I2S3_SD, USART3_CK, UART5_TX, SDMMC1_CK and DCMI_D9. |
| 114 | PD0 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions CAN1_RX and FMC_D2. |
| 115 | PD1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions CAN1_TX and FMC_D3. |
| 116 | PD2 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED2, TIM3_ETR, UART5_RX, SDMMC1_CMD and DCMI_D11. |
| 117 | PD3 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI2_SCK/I2S2_CK, USART2_CTS, FMC_CLK, DCMI_D5 and LCD_G7. |
| 118 | PD4 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART2_RTS and FMC_NOE. |
| 119 | PD5 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART2_TX and FMC_NWE. |
| 120 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 121 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 122 | PD6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPI3_MOSI/I2S3_SD, SAI1_SD_A, USART2_RX, FMC_NWAIT, DCMI_D10 and LCD_B2. |
| 123 | PD7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART2_CK, SPDIFRX_IN0 and FMC_NE1. |
| 124 | PG9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPDIFRX_IN3, USART6_RX, QUADSPI_BK2_IO2, SAI2_FS_B, FMC_NE2/FMC_NCE and DCMI_VSYNC. |
| 125 | PG10 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions LCD_G3, SAI2_SD_B, FMC_NE3, DCMI_D2 and LCD_B2. |
| 126 | PG11 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions SPDIFRX_IN0, ETH_MII_TX_EN/ETH_RMII_TX_EN, DCMI_D3 and LCD_B3. |
| 127 | PG12 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions LPTIM1_IN1, SPI6_MISO, SPDIFRX_IN1, USART6_RTS, LCD_B4, FMC_NE4 and LCD_B1. |
| 128 | PG13 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED0, LPTIM1_OUT, SPI6_SCK, USART6_CTS, ETH_MII_TXD0/ETH_RMII_TXD0, FMC_A24 and LCD_R0. |
| 129 | PG14 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TRACED1, LPTIM1_ETR, SPI6_MOSI, USART6_TX, QUADSPI_BK2_IO3, ETH_MII_TXD1/ETH_RMII_TXD1, FMC_A25 and LCD_B0. |
| 130 | VSS | power_in | Ground reference for the digital supply domain; must be connected to ground. |
| 131 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
| 132 | PG15 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions USART6_CTS, FMC_SDNCAS and DCMI_D13. |
| 133 | PB3 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions JTDO/TRACESWO, TIM2_CH2, SPI1_SCK/I2S1_CK and SPI3_SCK/I2S3_CK. |
| 134 | PB4 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions NJTRST, TIM3_CH1, SPI1_MISO, SPI3_MISO and SPI2_NSS/I2S2_WS. |
| 135 | PB5 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM3_CH2, I2C1_SMBA, SPI1_MOSI/I2S1_SD, SPI3_MOSI/I2S3_SD, CAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, FMC_SDCKE1 and DCMI_D10. |
| 136 | PB6 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH1, HDMI-CEC, I2C1_SCL, USART1_TX, CAN2_TX, QUADSPI_BK1_NCS, FMC_SDNE1 and DCMI_D5. |
| 137 | PB7 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH2, I2C1_SDA, USART1_RX, FMC_NL and DCMI_VSYNC. |
| 138 | BOOT0 | input | Dedicated boot pin with input range 0 V to 9 V (Table 18); also serves as VPP for flash programming. |
| 139 | PB8 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH3, TIM10_CH1, I2C1_SCL, CAN1_RX, ETH_MII_TXD3, SDMMC1_D4, DCMI_D6 and LCD_B6. |
| 140 | PB9 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_CH4, TIM11_CH1, I2C1_SDA, SPI2_NSS/I2S2_WS, CAN1_TX, SDMMC1_D5, DCMI_D7 and LCD_B7. |
| 141 | PE0 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions TIM4_ETR, LPTIM1_ETR, UART8_Rx, SAI2_MCK_A, FMC_NBL0 and DCMI_D2. |
| 142 | PE1 | bidirectional | 5 V tolerant (FT) GPIO with alternate functions LPTIM1_IN2, UART8_Tx, FMC_NBL1 and DCMI_D3. |
| 143 | PDR_ON | power_in | Power-down reset control pin; must be connected as described in the power supply supervisor section (Section 3.17). |
| 144 | VDD | power_in | Standard supply voltage, 1.7 V to 3.6 V, for I/Os and internal logic. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-144(20x20) |
| Category | Embedded Processors & Controllers |
| Pins | 144 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA, VDD, VBAT and VDDUSB) | VDD-VSS | -0.3 | 4 | V | 102 | ||
| Input voltage on TTa pins (min VSS − 0.3 V as printed) | VIN | 4 | V | 102 | |||
| Input voltage on any other pin (min VSS − 0.3 V as printed) | VIN | 4 | V | 102 | |||
| Input voltage on BOOT pin (min VSS as printed) | VIN | 9 | V | 102 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 102 | |||
| Variations between all the different ground pins (includes VREF- pin) | /VSSX −VSS/ | 50 | mV | 102 | |||
| Total current into sum of all VDD_x power lines (source) | ΣIVDD | 320 | mA | 103 | |||
| Total current out of sum of all VSS_x ground lines (sink) | ΣIVSS | -320 | mA | 103 | |||
| Total current into VDDUSB power line (source) | ΣIVDDUSB | 25 | mA | 103 | |||
| Maximum current into each VDD_x power line (source) | IVDD | 100 | mA | 103 | |||
| Maximum current out of each VSS_x ground line (sink) | IVSS | -100 | mA | 103 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 103 | |||
| Output current sourced by any I/Os and control pin | IIO | -25 | mA | 103 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 103 | |||
| Total output current sourced by sum of all I/Os and control pins | ΣIIO | -120 | mA | 103 | |||
| Injected current on FT, FTf, RST and B pins | IINJ(PIN) | -5 | 0 | mA | 103 | ||
| Injected current on TTa pins | IINJ(PIN) | -5 | 5 | mA | 103 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 103 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 103 | ||
| Maximum junction temperature | TJ | 125 | °C | 103 | |||
| Internal AHB clock frequency | fHCLK | 0 | 144 | MHz | Power Scale 3 (VOS=0x01), Regulator ON, over-drive OFF | 104 | |
| Internal AHB clock frequency | fHCLK | 0 | 168 | MHz | Power Scale 2 (VOS=0x10), Regulator ON, over-drive OFF | 104 | |
| Internal AHB clock frequency | fHCLK | 0 | 180 | MHz | Power Scale 2 (VOS=0x10), Regulator ON, over-drive ON | 104 | |
| Internal AHB clock frequency | fHCLK | 0 | 216 | MHz | Power Scale 1 (VOS=0x11), Regulator ON, over-drive ON (6 suffix version) | 104 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 45 | MHz | Over-drive OFF | 104 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 54 | MHz | Over-drive ON | 104 | |
| Internal APB2 clock frequency | fPCLK2 | 0 | 90 | MHz | Over-drive OFF | 104 | |
| Internal APB2 clock frequency | fPCLK2 | 0 | 108 | MHz | Over-drive ON | 104 | |
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 104 | ||
| Analog operating voltage (ADC limited to 1.2 M samples), must be same potential as VDD | VDDA | 1.7 | 2.4 | V | ADC limited to 1.2 M samples | 104 | |
| Analog operating voltage (ADC limited to 2.4 M samples) | VDDA | 2.4 | 3.6 | V | ADC limited to 2.4 M samples | 104 | |
| USB supply voltage (PA11, PA12, PB14, PB15) | VDDUSB | 1.7 | 3.3 | 3.6 | V | USB not used | 104 |
| USB supply voltage (PA11, PA12, PB14, PB15) | VDDUSB | 3 | 3.6 | V | USB used | 104 | |
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 104 | ||
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 | V12 | 1.08 | 1.14 | 1.2 | V | Power Scale 3, 144 MHz HCLK max frequency | 105 |
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 | V12 | 1.2 | 1.26 | 1.32 | V | Power Scale 2, 168 MHz (over-drive OFF) or 180 MHz (over-drive ON) | 105 |
| Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 | V12 | 1.26 | 1.32 | 1.4 | V | Power Scale 1, 180 MHz (over-drive OFF) or 216 MHz (over-drive ON) | 105 |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 105 | |
| Input voltage on RST and FT pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 105 | |
| Input voltage on TTa pins (max VDDA+0.3 V as printed) | VIN | -0.3 | V | 105 | |||
| Input voltage on BOOT pin | VIN | 0 | 9 | V | 105 | ||
| Power dissipation, LQFP144 | PD | 500 | mW | TA = 85 °C for suffix 6 | 105 | ||
| Ambient temperature, 6 suffix version (maximum power dissipation) | TA | -40 | 85 | °C | Maximum power dissipation | 105 | |
| Ambient temperature, 6 suffix version (low power dissipation) | TA | -40 | 105 | °C | Low power dissipation | 105 | |
| Junction temperature range, 6 suffix version | TJ | -40 | 105 | °C | 6 suffix version | 105 | |
| VDD rise time rate | tVDD | 20 | µs/V | Power-up, regulator OFF | 107 | ||
| VDD fall time rate | tVDD | 20 | µs/V | Power-down, regulator OFF | 107 | ||
| VCAP_1 and VCAP_2 rise time rate | tVCAP | 20 | µs/V | Power-up, regulator OFF | 107 | ||
| VCAP_1 and VCAP_2 fall time rate | tVCAP | 20 | µs/V | Power-down, regulator OFF | 107 | ||
| Power-on/power-down reset threshold | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 108 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 108 |
| PDR hysteresis | VPDRhyst | 40 | mV | 108 | |||
| POR reset temporization | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | 108 | |
| InRush energy on voltage regulator power-on (POR or wake-up from Standby) | ERUSH | 5.4 | µC | VDD = 1.7 V, TA = 105 °C, IRUSH = 171 mA for 31 µs | 108 | ||
| Over-drive switch enable time (HSE max for 4 MHz and min for 26 MHz) | Tod_swen | 45 | 100 | µs | HSE max for 4 MHz and min for 26 MHz | 109 | |
| Over-drive switch disable time (HSE max for 4 MHz and min for 26 MHz) | Tod_swdis | 20 | 80 | µs | HSE max for 4 MHz and min for 26 MHz | 109 |
CAD (KiCad official)
- Symbol:
STM32F745ZGT6 - Footprint:
Package_QFP:LQFP-144_20x20mm_P0.5mm - 3D model: LQFP-144(20x20) (KiCad packages3D, STEP)
- 3D model files:
stm32f745zgt6-etched.step/stm32f745zgt6-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f745zgt6.step/stm32f745zgt6.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (230 pp, sha256
23a9ec5dfd13ea2e, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).