Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

STM32F413CGU6

STMicroelectronics · ST Microelectronics · UFQFPN-48(7x7)

STM32F413CGU6 from STMicroelectronics, in a UFQFPN-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 VBAT power_in Backup supply pin for the RTC and backup domain.
2 PC13-ANTI_TAMP bidirectional 5 V-tolerant I/O supplied through the power switch (3 mA max sink), so output mode is limited to 2 MHz with 30 pF max load and it must not source current; additional function TAMP_1.
3 PC14-OSC32_IN bidirectional GPIO supplied through the power switch (output limited to 2 MHz, 30 pF max); additional function OSC32_IN for the 32 kHz oscillator, and not 5 V tolerant in oscillator mode.
4 PC15-OSC32_OUT bidirectional GPIO supplied through the power switch (output limited to 2 MHz, 30 pF max); additional function OSC32_OUT for the 32 kHz oscillator, and not 5 V tolerant in oscillator mode.
5 PH0-OSC_IN bidirectional GPIO that is also the OSC_IN input of the 4-26 MHz crystal oscillator; not 5 V tolerant in oscillator mode.
6 PH1-OSC_OUT bidirectional GPIO that is also the OSC_OUT output of the 4-26 MHz crystal oscillator; not 5 V tolerant in oscillator mode.
7 NRST bidirectional Bidirectional reset pin with embedded weak pull-up resistor.
8 VSSA/VREF- power_in Analog ground (VSSA) supply pin.
9 VDDA/VREF+ power_in Analog supply (VDDA) pin, which also serves as the ADC/DAC positive reference VREF+ on this package.
10 PA0 bidirectional 5 V-tolerant I/O with TIM2_CH1/ETR, TIM5_CH1, TIM8_ETR, USART2_CTS and UART4_TX alternates; additional functions ADC1_IN0 and WKUP1.
11 PA1 bidirectional 5 V-tolerant I/O with TIM2_CH2, TIM5_CH2, SPI4_MOSI/I2S4_SD, USART2_RTS, UART4_RX and QUADSPI_BK1_IO3 alternates; additional function ADC1_IN1.
12 PA2 bidirectional 5 V-tolerant I/O with TIM2_CH3, TIM5_CH3, TIM9_CH1, I2S2_CKIN, USART2_TX and FSMC_D4/DA4 alternates; additional function ADC1_IN2.
13 PA3 bidirectional 5 V-tolerant I/O with TIM2_CH4, TIM5_CH4, TIM9_CH2, I2S2_MCK, USART2_RX, SAI1_SD_B and FSMC_D5/DA5 alternates; additional function ADC1_IN3.
14 PA4 bidirectional 3.3 V-tolerant (TTa) I/O with SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, USART2_CK, DFSDM1_DATIN1 and FSMC_D6/DA6 alternates; additional functions ADC1_IN4 and DAC_OUT1.
15 PA5 bidirectional 3.3 V-tolerant (TTa) I/O with TIM2_CH1/ETR, TIM8_CH1N, SPI1_SCK/I2S1_CK, DFSDM1_CKIN1 and FSMC_D7/DA7 alternates; additional functions ADC1_IN5 and DAC_OUT2.
16 PA6 bidirectional 5 V-tolerant I/O with TIM1_BKIN, TIM3_CH1, TIM8_BKIN, SPI1_MISO, I2S2_MCK, TIM13_CH1, QUADSPI_BK2_IO0 and SDIO_CMD alternates; additional function ADC1_IN6.
17 PA7 bidirectional 5 V-tolerant I/O with TIM1_CH1N, TIM3_CH2, TIM8_CH1N, SPI1_MOSI/I2S1_SD, TIM14_CH1 and QUADSPI_BK2_IO1 alternates; additional function ADC1_IN7.
18 PB0 bidirectional 5 V-tolerant I/O with TIM1_CH2N, TIM3_CH3, TIM8_CH2N and SPI5_SCK/I2S5_CK alternates; additional function ADC1_IN8.
19 PB1 bidirectional 5 V-tolerant I/O with TIM1_CH3N, TIM3_CH4, TIM8_CH3N, SPI5_NSS/I2S5_WS, DFSDM1_DATIN0 and QUADSPI_CLK alternates; additional function ADC1_IN9.
20 PB2 bidirectional 5 V-tolerant I/O with LPTIM1_OUT, DFSDM1_CKIN0 and QUADSPI_CLK alternates; additional function BOOT1.
21 PB10 bidirectional 5 V-tolerant I/O (FTf, I2C FM+ option) with TIM2_CH3, I2C2_SCL, SPI2_SCK/I2S2_CK, USART3_TX, I2CFMP1_SCL, DFSDM2_CKOUT and SDIO_D7 alternates.
22 VCAP_1 passive Supply pin for connecting the external VCAP_1 capacitor of the internal 1.2 V regulator.
23 VSS power_in Digital ground supply pin.
24 VDD power_in Digital supply pin (1.7 to 3.6 V application supply).
25 PB12 bidirectional 5 V-tolerant I/O with TIM1_BKIN, I2C2_SMBA, SPI2_NSS/I2S2_WS, SPI4_NSS, SPI3_SCK/I2S3_CK, USART3_CK, CAN2_RX, DFSDM1_DATIN1, UART5_RX and FSMC_D13/DA13 alternates.
26 PB13 bidirectional 5 V-tolerant I/O with TIM1_CH1N, I2CFMP1_SMBA, SPI2_SCK/I2S2_CK, SPI4_SCK/I2S4_CK, USART3_CTS, CAN2_TX, DFSDM1_CKIN1 and UART5_TX alternates.
27 PB14 bidirectional 5 V-tolerant I/O (FTf, I2C FM+ option) with TIM1_CH2N, TIM8_CH2N, I2CFMP1_SDA, SPI2_MISO, USART3_RTS, TIM12_CH1, FSMC_D0/DA0 and SDIO_D6 alternates.
28 PB15 bidirectional 5 V-tolerant I/O (FTf, I2C FM+ option) with RTC_REFIN, TIM1_CH3N, TIM8_CH3N, I2CFMP1_SCL, SPI2_MOSI/I2S2_SD, TIM12_CH2 and SDIO_CK alternates.
29 PA8 bidirectional 5 V-tolerant I/O with MCO_1, TIM1_CH1, I2C3_SCL, USART1_CK, UART7_RX, USB_FS_SOF, CAN3_RX and SDIO_D1 alternates.
30 PA9 bidirectional 5 V-tolerant I/O with TIM1_CH2, I2C3_SMBA, SPI2_SCK/I2S2_CK, USART1_TX, USB_FS_VBUS and SDIO_D2 alternates.
31 PA10 bidirectional 5 V-tolerant I/O with TIM1_CH3, SPI2_MOSI/I2S2_SD, SPI5_MOSI/I2S5_SD, USART1_RX and USB_FS_ID alternates.
32 PA11 bidirectional 5 V-tolerant I/O with TIM1_CH4, SPI2_NSS/I2S2_WS, USART1_CTS, USART6_TX, CAN1_RX, USB_FS_DM and UART4_RX alternates.
33 PA12 bidirectional 5 V-tolerant I/O with TIM1_ETR, SPI2_MISO, USART1_RTS, USART6_RX, CAN1_TX, USB_FS_DP and UART4_TX alternates.
34 PA13 bidirectional 5 V-tolerant I/O whose function after reset is JTMS-SWDIO.
35 VSS power_in Digital ground supply pin.
36 VDD power_in Digital supply pin (1.7 to 3.6 V application supply).
37 PA14 bidirectional 5 V-tolerant I/O whose function after reset is JTCK-SWCLK.
38 PA15 bidirectional 5 V-tolerant I/O whose function after reset is JTDI, with TIM2_CH1/ETR, SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, USART1_TX, UART7_TX, SAI1_MCLK_A and CAN3_TX alternates.
39 PB3 bidirectional 5 V-tolerant I/O (FTf) whose function after reset is JTDO-SWO, with TIM2_CH2, I2CFMP1_SDA, SPI1_SCK/I2S1_CK, SPI3_SCK/I2S3_CK, USART1_RX, UART7_RX, I2C2_SDA, SAI1_SD_A and CAN3_RX alternates.
40 PB4 bidirectional 5 V-tolerant I/O whose function after reset is JTRST, with TIM3_CH1, SPI1_MISO, SPI3_MISO, UART7_TX, I2C3_SDA, SAI1_SCK_A, CAN3_TX and SDIO_D0 alternates.
41 PB5 bidirectional 5 V-tolerant I/O with LPTIM1_IN1, TIM3_CH2, I2C1_SMBA, SPI1_MOSI/I2S1_SD, SPI3_MOSI/I2S3_SD, CAN2_RX, SAI1_FS_A, UART5_RX and SDIO_D3 alternates.
42 PB6 bidirectional 5 V-tolerant I/O with LPTIM1_ETR, TIM4_CH1, I2C1_SCL, USART1_TX, CAN2_TX, QUADSPI_BK1_NCS, UART5_TX and SDIO_D0 alternates.
43 PB7 bidirectional 5 V-tolerant I/O with LPTIM1_IN2, TIM4_CH2, I2C1_SDA, USART1_RX and FSMC_NL alternates.
44 BOOT0 input Dedicated boot mode selection input; additional function VPP.
45 PB8 bidirectional 5 V-tolerant I/O with LPTIM1_OUT, TIM4_CH3, TIM10_CH1, I2C1_SCL, SPI5_MOSI/I2S5_SD, CAN1_RX, I2C3_SDA, UART5_RX and SDIO_D4 alternates.
46 PB9 bidirectional 5 V-tolerant I/O with TIM4_CH4, TIM11_CH1, I2C1_SDA, SPI2_NSS/I2S2_WS, CAN1_TX, I2C2_SDA, UART5_TX and SDIO_D5 alternates.
47 VSS power_in Digital ground supply pin.
48 VDD power_in Digital supply pin (1.7 to 3.6 V application supply).
49 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package UFQFPN-48(7x7)
Category Embedded Processors & Controllers
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
External main supply voltage (including VDDA, VDD, VDDUSB and VBAT) VDD-VSS -0.3 4 V 79
Input voltage on TTa pins VIN 4 V 79
Input voltage on any other pin VIN 4 V 79
Variations between different VDD power pins /ΔVDDx/ 50 mV 79
Variations between all the different ground pins including VREF- /VSSX −VSS/ 50 mV 79
Total current into sum of all VDD_x power lines (source) ΣIVDD 180 mA 80
Total current out of sum of all VSS_x ground lines (sink) ΣIVSS -180 mA 80
Total current into VDDUSB power lines (source) ΣIVDDUSB 25 mA 80
Maximum current into each VDD_x power line (source) IVDD 100 mA 80
Maximum current out of each VSS_x ground line (sink) IVSS -100 mA 80
Output current sunk by any I/O and control pin IIO 25 mA 80
Output current sourced by any I/O and control pin IIO -25 mA 80
Total output current sunk by sum of all I/O and control pins ΣIIO 120 mA 80
Total output current sunk by sum of all USB I/Os 25 mA 80
Total output current sourced by sum of all I/Os and control pins ΣIIO -120 mA 80
Injected current on FT and TC pins IINJ(PIN) -5 0 mA 80
Injected current on TTa pins IINJ(PIN) -5 5 mA 80
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) -25 25 mA 80
Storage temperature range TSTG -65 150 °C 80
Maximum junction temperature TJ 125 °C 80
Internal AHB clock frequency fHCLK 0 64 MHz Power Scale3: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x01 81
Internal AHB clock frequency fHCLK 0 84 MHz Power Scale2: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x10 81
Internal AHB clock frequency fHCLK 0 100 MHz Power Scale1: Regulator ON, VOS[1:0] bits in PWR_CR register = 0x11 81
Internal APB1 clock frequency fPCLK1 0 50 MHz 81
Internal APB2 clock frequency fPCLK2 0 100 MHz 81
Standard operating voltage VDD 1.7 3.6 V 81
Analog operating voltage (ADC limited to 1.2 M samples) VDDA 1.7 2.4 V ADC limited to 1.2 M samples; must be the same potential as VDD 81
Analog operating voltage (ADC limited to 2.4 M samples) VDDA 2.4 3.6 V ADC limited to 2.4 M samples 81
USB supply voltage (supply voltage for PA11 and PA12 pins) VDDUSB 1.7 3.3 3.6 V USB not used 81
USB supply voltage (supply voltage for PA11 and PA12 pins) VDDUSB 3 3.6 V USB used 81
Backup operating voltage VBAT 1.65 3.6 V 81
Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 pins V12 1.08 1.14 1.2 V VOS[1:0] bits in PWR_CR register = 0x01; max frequency 64 MHz 81
Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 pins V12 1.2 1.26 1.32 V VOS[1:0] bits in PWR_CR register = 0x10; max frequency 84 MHz 81
Regulator ON: 1.2 V internal voltage on VCAP_1/VCAP_2 pins V12 1.26 1.32 1.38 V VOS[1:0] bits in PWR_CR register = 0x11; max frequency 100 MHz 81
Input voltage on RST, FT and TC pins VIN -0.3 5.5 V 2 V ≤ VDD ≤ 3.6 V 82
Input voltage on RST, FT and TC pins VIN -0.3 5.2 V VDD ≤ 2 V 82
Input voltage on TTa pins VIN -0.3 V 82
Input voltage on BOOT0 pin VIN 0 9 V 82
Power dissipation at TA = 85 °C for range 6 (UFQFPN48) PD 625 mW TA = 85 °C for range 6 (maximum power dissipation) 82
Ambient temperature for range 6, maximum power dissipation TA -40 85 °C Maximum power dissipation 82
Ambient temperature for range 6, low power dissipation TA -40 105 °C Low power dissipation 82
Junction temperature range (range 6) TJ -40 105 °C Range 6 82
VDD rise time rate tVDD 20 µs/V Regulator ON, power-up 84
VDD fall time rate tVDD 20 µs/V Regulator ON, power-down 84
ESR of external capacitor with a single VCAP pin available ESR 1 Ω Single VCAP pin available 84
Power-on/power-down reset threshold (falling edge) VPOR/PDR 1.6 1.68 1.76 V Falling edge 85
Power-on/power-down reset threshold (rising edge) VPOR/PDR 1.64 1.72 1.8 V Rising edge 85
PDR hysteresis VPDRhyst 40 mV 85
PVD hysteresis VPVDhyst 100 mV 85
BOR hysteresis VBORhyst 100 mV 86
POR reset timing TRSTTEMPO 0.5 1.5 3 ms 86
In-Rush energy on voltage regulator power-on (POR or wakeup from Standby) ERUSH 5.4 µC VDD = 1.7 V, TA = 125 °C, IRUSH = 171 mA for 31 µs 86
LSI frequency fLSI 16.1 32 47 kHz VDD = 3 V, TA = -40 to 125 °C 112
LSI oscillator startup time tsu(LSI) 15 40 µs 112
LSI oscillator power consumption IDD(LSI) 0.4 0.6 µA 112
Capacitance of external capacitor with a single VCAP pin available CEXT 4.7 µF Single VCAP pin available 84

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: STM32F413CGU6
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: UFQFPN-48(7x7), generated on the KiCad land (body 7 x 7 mm, terminals on the pads, 0.55 mm tall, datasheet A, nominal). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: stm32f413cgu6-etched.step / stm32f413cgu6-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); stm32f413cgu6.step / stm32f413cgu6.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (203 pp, sha256 4157ab59cb88ac0f, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF