main
Ray
Publish 0.1.0
fbf8454
STM32F410RBT7
STMicroelectronics · ST Microelectronics · LQFP-64(10x10)
STM32F410RBT7 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Power supply for the RTC, external 32 kHz oscillator and backup registers through the power switch when VDD is not present, 1.65 to 3.6 V. |
| 2 | PC13 | bidirectional | Supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF max load and the pin must not be used as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | Same power switch limits as PC13 (3 mA sink, 2 MHz at 30 pF max output speed), 5 V tolerant except in oscillator mode, default function OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | Same power switch limits as PC13 (3 mA sink, 2 MHz at 30 pF max output speed), default function OSC32_OUT. |
| 5 | PH0 - OSC_IN | bidirectional | Default function OSC_IN, the high-speed oscillator input; 5 V tolerant except in analog or oscillator mode. |
| 6 | PH1 - OSC_OUT | bidirectional | Default function OSC_OUT, the high-speed oscillator output; 5 V tolerant except in analog or oscillator mode. |
| 7 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN1, EVENTOUT, ADC1_10 and WKUP2 functions. |
| 9 | PC1 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, EVENTOUT, ADC1_11 and WKUP3 functions. |
| 10 | PC2 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN2, SPI2_MISO, EVENTOUT and ADC1_12 functions. |
| 11 | PC3 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_ETR, SPI2_MOSI/I2S2_SD, EVENTOUT and ADC1_13 functions. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative reference voltage, connected to VSS with decoupling. |
| 13 | VDDA/VREF+ | power_in | Analog supply 1.7 to 3.6 V for ADC, reset blocks, RCs and PLL, connected to VDD with decoupling; also positive ADC reference. |
| 14 | PA0 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH1, USART2_CTS, EVENTOUT, ADC1_0 and WKUP1 functions. |
| 15 | PA1 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH2, USART2_RTS, EVENTOUT and ADC1_1 functions. |
| 16 | PA2 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH3, TIM9_CH1, I2S2_CKIN, USART2_TX, EVENTOUT and ADC1_2 functions. |
| 17 | PA3 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH4, TIM9_CH2, I2S2_MCK, USART2_RX, EVENTOUT and ADC1_3 functions. |
| 18 | VSS | power_in | Ground pin. |
| 19 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 20 | PA4 | bidirectional | 5 V tolerant GPIO (FT) with SPI1_NSS/I2S1_WS, USART2_CK, EVENTOUT and ADC1_4 functions. |
| 21 | PA5 | bidirectional | 3.3 V standard I/O (TC) with SPI1_SCK/I2S1_CK, EVENTOUT, ADC1_5 and DAC_OUT1 functions. |
| 22 | PA6 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_BKIN, SPI1_MISO, I2S2_MCK, EVENTOUT and ADC1_6 functions. |
| 23 | PA7 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH1N, SPI1_MOSI/I2S1_SD, EVENTOUT and ADC1_7 functions. |
| 24 | PC4 | bidirectional | 5 V tolerant GPIO (FT) with TIM9_CH1, EVENTOUT and ADC1_14 functions. |
| 25 | PC5 | bidirectional | 5 V tolerant GPIO (FT) with TIM9_CH2, I2C4_SMBA, EVENTOUT and ADC1_15 functions. |
| 26 | PB0 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2N, SPI5_SCK/I2S5_CK, EVENTOUT and ADC1_8 functions. |
| 27 | PB1 | bidirectional | 3.3 V standard I/O (TC) with TIM1_CH3N, SPI5_NSS/I2S5_WS, EVENTOUT and ADC1_9 functions. |
| 28 | PB2 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, EVENTOUT and BOOT1 functions. |
| 29 | PB10 | bidirectional | 5 V tolerant GPIO (FT) with I2C2_SCL, SPI2_SCK/I2S2_CK, I2S1_MCK, I2C4_SCL and EVENTOUT functions. |
| 30 | VCAP_1 | power_in | Connection to the external capacitor of the internal voltage regulator output. |
| 31 | VSS | power_in | Ground pin. |
| 32 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 33 | PB12 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_BKIN, TIM5_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS and EVENTOUT functions. |
| 34 | PB13 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH1N, I2C4_SMBA, SPI2_SCK/I2S2_CK and EVENTOUT functions. |
| 35 | PB14 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2N, I2C4_SDA, SPI2_MISO and EVENTOUT functions. |
| 36 | PB15 | bidirectional | 5 V tolerant GPIO (FT) with RTC_50Hz, TIM1_CH3N, I2C4_SCL, SPI2_MOSI/I2S2_SD and EVENTOUT functions. |
| 37 | PC6 | bidirectional | 5 V tolerant GPIO (FT) with TRACECLK, I2C4_SCL, I2S2_MCK, USART6_TX and EVENTOUT functions. |
| 38 | PC7 | bidirectional | 5 V tolerant GPIO (FT) with I2C4_SDA, SPI2_SCK/I2S2_CK, I2S1_MCK, USART6_RX and EVENTOUT functions. |
| 39 | PC8 | bidirectional | 5 V tolerant GPIO (FT) with USART6_CK and EVENTOUT functions. |
| 40 | PC9 | bidirectional | 5 V tolerant GPIO (FT) with MCO_2, I2C4_SDA, I2S2_CKIN and EVENTOUT functions. |
| 41 | PA8 | bidirectional | 5 V tolerant GPIO (FT) with MCO_1, TIM1_CH1, I2C4_SCL, USART1_CK and EVENTOUT functions. |
| 42 | PA9 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2, USART1_TX and EVENTOUT functions. |
| 43 | PA10 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH3, SPI5_MOSI/I2S5_SD, USART1_RX and EVENTOUT functions. |
| 44 | PA11 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH4, USART1_CTS, USART6_TX and EVENTOUT functions. |
| 45 | PA12 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_ETR, SPI5_MISO, USART1_RTS, USART6_RX and EVENTOUT functions. |
| 46 | PA13 | bidirectional | 5 V tolerant GPIO (FT) with JTMS-SWDIO debug function and EVENTOUT. |
| 47 | VSS | power_in | Ground pin. |
| 48 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 49 | PA14 | bidirectional | 5 V tolerant GPIO (FT) with JTCK-SWCLK debug function and EVENTOUT. |
| 50 | PA15 | bidirectional | 5 V tolerant GPIO (FT) with JTDI, SPI1_NSS/I2S1_WS, USART1_TX and EVENTOUT functions. |
| 51 | PC10 | bidirectional | 5 V tolerant GPIO (FT) with TRACED0, TIM5_CH2 and EVENTOUT functions. |
| 52 | PC11 | bidirectional | 5 V tolerant GPIO (FT) with TRACED1, TIM5_CH3 and EVENTOUT functions. |
| 53 | PC12 | bidirectional | 5 V tolerant GPIO (FT) with TRACED2, TIM11_CH1 and EVENTOUT functions. |
| 54 | PB11 | bidirectional | 5 V tolerant GPIO (FT) with TRACED3, TIM5_CH4, I2C2_SDA, I2S2_CKIN and EVENTOUT functions. |
| 55 | PB3 | bidirectional | 5 V tolerant GPIO (FT) with JTDO-SWO, I2C4_SDA, SPI1_SCK/I2S1_CK, USART1_RX, I2C2_SDA and EVENTOUT functions. |
| 56 | PB4 | bidirectional | 5 V tolerant GPIO (FT) with JTRST, SPI1_MISO and EVENTOUT functions. |
| 57 | PB5 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI/I2S1_SD and EVENTOUT functions. |
| 58 | PB6 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_ETR, I2C1_SCL, USART1_TX and EVENTOUT functions. |
| 59 | PB7 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN2, I2C1_SDA, USART1_RX and EVENTOUT functions. |
| 60 | BOOT0 | input | Boot pin that selects the boot option at startup (user Flash, system memory or embedded SRAM); also carries the VPP function. |
| 61 | PB8 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, I2C1_SCL, SPI5_MOSI/I2S5_SD and EVENTOUT functions. |
| 62 | PB9 | bidirectional | 5 V tolerant GPIO (FT) with TIM11_CH1, I2C1_SDA, SPI2_NSS/I2S2_WS, I2C2_SDA and EVENTOUT functions. |
| 63 | VSS | power_in | Ground pin. |
| 64 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.7 | 3.6 | V | 52 | ||
| Backup operating voltage | VBAT | 1.65 | 3.6 | V | 52 | ||
| Analog operating voltage | VDDA | 1.7 | 2.4 | V | ADC limited to 1.2 M samples; must be same potential as VDD | 52 | |
| Analog operating voltage | VDDA | 2.4 | 3.6 | V | ADC limited to 2.4 M samples | 52 | |
| Internal AHB clock frequency | fHCLK | 0 | 64 | MHz | Power Scale3: Regulator ON, VOS[1:0]=0x01 | 52 | |
| Internal AHB clock frequency | fHCLK | 0 | 84 | MHz | Power Scale2: Regulator ON, VOS[1:0]=0x10 | 52 | |
| Internal AHB clock frequency | fHCLK | 0 | 100 | MHz | Power Scale1: Regulator ON, VOS[1:0]=0x11 | 52 | |
| Internal APB1 clock frequency | fPCLK1 | 0 | 50 | MHz | 52 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 100 | MHz | 52 | ||
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 52 | |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | 5.2 | V | VDD ≤ 2 V | 52 | |
| Input voltage on BOOT0 pin | VIN | 0 | 9 | V | 52 | ||
| Ambient temperature for range 7 | TA | -40 | 105 | °C | Maximum power dissipation, range 7 | 52 | |
| Ambient temperature for range 7 | TA | -40 | 125 | °C | Low power dissipation, range 7 | 52 | |
| Junction temperature range range 7 | TJ | -40 | 125 | °C | Range 7 | 52 | |
| Maximum allowed package power dissipation LQFP64 | PD | 435 | mW | TA = 85 °C (range 6) or 105 °C (range 7) | 52 | ||
| External main supply voltage (VDD, VDDA, VBAT) | VDD-VSS | -0.3 | 4 | V | 50 | ||
| Input voltage on FT and TC pins | VIN | -0.3 | V | max VDD+4.0 V | 50 | ||
| Input voltage on any other pin | VIN | -0.3 | 4 | V | 50 | ||
| Input voltage for BOOT0 | VIN | 9 | V | min VSS | 50 | ||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 50 | |||
| Total current into sum of all VDD power lines (source) | ΣIVDD | 160 | mA | 51 | |||
| Total current out of sum of all VSS ground lines (sink) | ΣIVSS | -160 | mA | 51 | |||
| Maximum current into each VDD power line (source) | IVDD | 100 | mA | 51 | |||
| Maximum current out of each VSS ground line (sink) | IVSS | -100 | mA | 51 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 51 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 51 | |||
| Total output current sunk by sum of all I/O and control pins | ΣIIO | 120 | mA | 51 | |||
| Total output current sourced by sum of all I/O and control pins | ΣIIO | -120 | mA | 51 | |||
| Injected current on FT and TC pins | IINJ(PIN) | -5 | 0 | mA | 51 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 51 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 51 | ||
| Maximum junction temperature | TJ | 130 | °C | 51 | |||
| Power-on/power-down reset threshold | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 56 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 56 |
| Brownout level 1 threshold | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 56 |
| POR reset timing | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | 56 | |
| VDD rise time rate | tVDD | 20 | µs/V | Regulator ON, upper limit unbounded | 55 | ||
| VDD fall time rate | tVDD | 20 | µs/V | Regulator ON, upper limit unbounded | 55 | ||
| Supply current in Run mode | IDD | 17.7 | 20.5 | mA | External clock, all peripherals enabled, fHCLK 100 MHz, VDD=3.6 V, typ at TA=25 °C, max at TA=125 °C | 59 | |
| Supply current in Standby mode | IDD_STBY | 3.4 | 8.9 | µA | LSE and RTC ON, VDD=3.6 V, max at TA=85 °C | 70 | |
| Supply current in Stop mode | IDD_STOP | 105.6 | 385.1 | µA | Flash in Stop mode, all oscillators OFF, main regulator, VDD=1.7 V, max at TA=85 °C | 69 | |
| HSI oscillator frequency | fHSI | 16 | MHz | 82 | |||
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -8 | 5.5 | % | TA = -40 to 125 °C | 82 | |
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -4 | 4 | % | TA = -10 to 85 °C | 82 | |
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -1 | 1 | % | TA = 25 °C | 82 | |
| HSI oscillator power consumption | IDD(HSI) | 60 | 80 | µA | 82 | ||
| LSI oscillator frequency | fLSI | 17 | 32 | 47 | kHz | VDD = 3 V, TA = -40 to 125 °C | 82 |
| PLL input clock | fPLL_IN | 0.95 | 1 | 2.1 | MHz | 83 | |
| PLL multiplier output clock | fPLL_OUT | 24 | 100 | MHz | 83 | ||
| PLL VCO output | fVCO_OUT | 100 | 432 | MHz | 83 | ||
| 48 MHz PLL multiplier output clock | fPLL48_OUT | 48 | 75 | MHz | 83 | ||
| PLL lock time | tLOCK | 75 | 200 | µs | VCO freq = 100 MHz | 83 | |
| PLL lock time | tLOCK | 100 | 300 | µs | VCO freq = 432 MHz | 83 | |
| Modulation frequency | fMod | 10 | kHz | SSCG | 84 | ||
| Peak modulation depth | md | 0.25 | 2 | % | SSCG | 84 | |
| External user clock source frequency | fHSE_ext | 1 | 50 | MHz | 77 | ||
| OSC_IN high or low time | tw(HSE) | 5 | ns | 77 | |||
| HSE oscillator frequency | fOSC_IN | 4 | 26 | MHz | 80 |
CAD (KiCad official)
- Symbol:
STM32F410RBT7 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f410rbt7-etched.step/stm32f410rbt7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f410rbt7.step/stm32f410rbt7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (141 pp, sha256
54617c5ae13d5ecf, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32F410RBT7
**STMicroelectronics** · ST Microelectronics · LQFP-64(10x10)
STM32F410RBT7 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Power supply for the RTC, external 32 kHz oscillator and backup registers through the power switch when VDD is not present, 1.65 to 3.6 V. |
| 2 | PC13 | bidirectional | Supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF max load and the pin must not be used as a current source. |
| 3 | PC14-OSC32_IN | bidirectional | Same power switch limits as PC13 (3 mA sink, 2 MHz at 30 pF max output speed), 5 V tolerant except in oscillator mode, default function OSC32_IN. |
| 4 | PC15-OSC32_OUT | bidirectional | Same power switch limits as PC13 (3 mA sink, 2 MHz at 30 pF max output speed), default function OSC32_OUT. |
| 5 | PH0 - OSC_IN | bidirectional | Default function OSC_IN, the high-speed oscillator input; 5 V tolerant except in analog or oscillator mode. |
| 6 | PH1 - OSC_OUT | bidirectional | Default function OSC_OUT, the high-speed oscillator output; 5 V tolerant except in analog or oscillator mode. |
| 7 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |
| 8 | PC0 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN1, EVENTOUT, ADC1_10 and WKUP2 functions. |
| 9 | PC1 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, EVENTOUT, ADC1_11 and WKUP3 functions. |
| 10 | PC2 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN2, SPI2_MISO, EVENTOUT and ADC1_12 functions. |
| 11 | PC3 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_ETR, SPI2_MOSI/I2S2_SD, EVENTOUT and ADC1_13 functions. |
| 12 | VSSA/VREF- | power_in | Analog ground and negative reference voltage, connected to VSS with decoupling. |
| 13 | VDDA/VREF+ | power_in | Analog supply 1.7 to 3.6 V for ADC, reset blocks, RCs and PLL, connected to VDD with decoupling; also positive ADC reference. |
| 14 | PA0 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH1, USART2_CTS, EVENTOUT, ADC1_0 and WKUP1 functions. |
| 15 | PA1 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH2, USART2_RTS, EVENTOUT and ADC1_1 functions. |
| 16 | PA2 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH3, TIM9_CH1, I2S2_CKIN, USART2_TX, EVENTOUT and ADC1_2 functions. |
| 17 | PA3 | bidirectional | 5 V tolerant GPIO (FT) with TIM5_CH4, TIM9_CH2, I2S2_MCK, USART2_RX, EVENTOUT and ADC1_3 functions. |
| 18 | VSS | power_in | Ground pin. |
| 19 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 20 | PA4 | bidirectional | 5 V tolerant GPIO (FT) with SPI1_NSS/I2S1_WS, USART2_CK, EVENTOUT and ADC1_4 functions. |
| 21 | PA5 | bidirectional | 3.3 V standard I/O (TC) with SPI1_SCK/I2S1_CK, EVENTOUT, ADC1_5 and DAC_OUT1 functions. |
| 22 | PA6 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_BKIN, SPI1_MISO, I2S2_MCK, EVENTOUT and ADC1_6 functions. |
| 23 | PA7 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH1N, SPI1_MOSI/I2S1_SD, EVENTOUT and ADC1_7 functions. |
| 24 | PC4 | bidirectional | 5 V tolerant GPIO (FT) with TIM9_CH1, EVENTOUT and ADC1_14 functions. |
| 25 | PC5 | bidirectional | 5 V tolerant GPIO (FT) with TIM9_CH2, I2C4_SMBA, EVENTOUT and ADC1_15 functions. |
| 26 | PB0 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2N, SPI5_SCK/I2S5_CK, EVENTOUT and ADC1_8 functions. |
| 27 | PB1 | bidirectional | 3.3 V standard I/O (TC) with TIM1_CH3N, SPI5_NSS/I2S5_WS, EVENTOUT and ADC1_9 functions. |
| 28 | PB2 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, EVENTOUT and BOOT1 functions. |
| 29 | PB10 | bidirectional | 5 V tolerant GPIO (FT) with I2C2_SCL, SPI2_SCK/I2S2_CK, I2S1_MCK, I2C4_SCL and EVENTOUT functions. |
| 30 | VCAP_1 | power_in | Connection to the external capacitor of the internal voltage regulator output. |
| 31 | VSS | power_in | Ground pin. |
| 32 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 33 | PB12 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_BKIN, TIM5_CH1, I2C2_SMBA, SPI2_NSS/I2S2_WS and EVENTOUT functions. |
| 34 | PB13 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH1N, I2C4_SMBA, SPI2_SCK/I2S2_CK and EVENTOUT functions. |
| 35 | PB14 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2N, I2C4_SDA, SPI2_MISO and EVENTOUT functions. |
| 36 | PB15 | bidirectional | 5 V tolerant GPIO (FT) with RTC_50Hz, TIM1_CH3N, I2C4_SCL, SPI2_MOSI/I2S2_SD and EVENTOUT functions. |
| 37 | PC6 | bidirectional | 5 V tolerant GPIO (FT) with TRACECLK, I2C4_SCL, I2S2_MCK, USART6_TX and EVENTOUT functions. |
| 38 | PC7 | bidirectional | 5 V tolerant GPIO (FT) with I2C4_SDA, SPI2_SCK/I2S2_CK, I2S1_MCK, USART6_RX and EVENTOUT functions. |
| 39 | PC8 | bidirectional | 5 V tolerant GPIO (FT) with USART6_CK and EVENTOUT functions. |
| 40 | PC9 | bidirectional | 5 V tolerant GPIO (FT) with MCO_2, I2C4_SDA, I2S2_CKIN and EVENTOUT functions. |
| 41 | PA8 | bidirectional | 5 V tolerant GPIO (FT) with MCO_1, TIM1_CH1, I2C4_SCL, USART1_CK and EVENTOUT functions. |
| 42 | PA9 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH2, USART1_TX and EVENTOUT functions. |
| 43 | PA10 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH3, SPI5_MOSI/I2S5_SD, USART1_RX and EVENTOUT functions. |
| 44 | PA11 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_CH4, USART1_CTS, USART6_TX and EVENTOUT functions. |
| 45 | PA12 | bidirectional | 5 V tolerant GPIO (FT) with TIM1_ETR, SPI5_MISO, USART1_RTS, USART6_RX and EVENTOUT functions. |
| 46 | PA13 | bidirectional | 5 V tolerant GPIO (FT) with JTMS-SWDIO debug function and EVENTOUT. |
| 47 | VSS | power_in | Ground pin. |
| 48 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
| 49 | PA14 | bidirectional | 5 V tolerant GPIO (FT) with JTCK-SWCLK debug function and EVENTOUT. |
| 50 | PA15 | bidirectional | 5 V tolerant GPIO (FT) with JTDI, SPI1_NSS/I2S1_WS, USART1_TX and EVENTOUT functions. |
| 51 | PC10 | bidirectional | 5 V tolerant GPIO (FT) with TRACED0, TIM5_CH2 and EVENTOUT functions. |
| 52 | PC11 | bidirectional | 5 V tolerant GPIO (FT) with TRACED1, TIM5_CH3 and EVENTOUT functions. |
| 53 | PC12 | bidirectional | 5 V tolerant GPIO (FT) with TRACED2, TIM11_CH1 and EVENTOUT functions. |
| 54 | PB11 | bidirectional | 5 V tolerant GPIO (FT) with TRACED3, TIM5_CH4, I2C2_SDA, I2S2_CKIN and EVENTOUT functions. |
| 55 | PB3 | bidirectional | 5 V tolerant GPIO (FT) with JTDO-SWO, I2C4_SDA, SPI1_SCK/I2S1_CK, USART1_RX, I2C2_SDA and EVENTOUT functions. |
| 56 | PB4 | bidirectional | 5 V tolerant GPIO (FT) with JTRST, SPI1_MISO and EVENTOUT functions. |
| 57 | PB5 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN1, I2C1_SMBA, SPI1_MOSI/I2S1_SD and EVENTOUT functions. |
| 58 | PB6 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_ETR, I2C1_SCL, USART1_TX and EVENTOUT functions. |
| 59 | PB7 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_IN2, I2C1_SDA, USART1_RX and EVENTOUT functions. |
| 60 | BOOT0 | input | Boot pin that selects the boot option at startup (user Flash, system memory or embedded SRAM); also carries the VPP function. |
| 61 | PB8 | bidirectional | 5 V tolerant GPIO (FT) with LPTIM1_OUT, I2C1_SCL, SPI5_MOSI/I2S5_SD and EVENTOUT functions. |
| 62 | PB9 | bidirectional | 5 V tolerant GPIO (FT) with TIM11_CH1, I2C1_SDA, SPI2_NSS/I2S2_WS, I2C2_SDA and EVENTOUT functions. |
| 63 | VSS | power_in | Ground pin. |
| 64 | VDD | power_in | Power supply 1.7 to 3.6 V for I/Os and internal regulator. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standard operating voltage | VDD | 1.7 | | 3.6 | V | | 52 |
| Backup operating voltage | VBAT | 1.65 | | 3.6 | V | | 52 |
| Analog operating voltage | VDDA | 1.7 | | 2.4 | V | ADC limited to 1.2 M samples; must be same potential as VDD | 52 |
| Analog operating voltage | VDDA | 2.4 | | 3.6 | V | ADC limited to 2.4 M samples | 52 |
| Internal AHB clock frequency | fHCLK | 0 | | 64 | MHz | Power Scale3: Regulator ON, VOS[1:0]=0x01 | 52 |
| Internal AHB clock frequency | fHCLK | 0 | | 84 | MHz | Power Scale2: Regulator ON, VOS[1:0]=0x10 | 52 |
| Internal AHB clock frequency | fHCLK | 0 | | 100 | MHz | Power Scale1: Regulator ON, VOS[1:0]=0x11 | 52 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 50 | MHz | | 52 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 100 | MHz | | 52 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | | 5.5 | V | 2 V ≤ VDD ≤ 3.6 V | 52 |
| Input voltage on RST, FT and TC pins | VIN | -0.3 | | 5.2 | V | VDD ≤ 2 V | 52 |
| Input voltage on BOOT0 pin | VIN | 0 | | 9 | V | | 52 |
| Ambient temperature for range 7 | TA | -40 | | 105 | °C | Maximum power dissipation, range 7 | 52 |
| Ambient temperature for range 7 | TA | -40 | | 125 | °C | Low power dissipation, range 7 | 52 |
| Junction temperature range range 7 | TJ | -40 | | 125 | °C | Range 7 | 52 |
| Maximum allowed package power dissipation LQFP64 | PD | | | 435 | mW | TA = 85 °C (range 6) or 105 °C (range 7) | 52 |
| External main supply voltage (VDD, VDDA, VBAT) | VDD-VSS | -0.3 | | 4 | V | | 50 |
| Input voltage on FT and TC pins | VIN | -0.3 | | | V | max VDD+4.0 V | 50 |
| Input voltage on any other pin | VIN | -0.3 | | 4 | V | | 50 |
| Input voltage for BOOT0 | VIN | | | 9 | V | min VSS | 50 |
| Variations between different VDD power pins | /ΔVDDx/ | | | 50 | mV | | 50 |
| Total current into sum of all VDD power lines (source) | ΣIVDD | | | 160 | mA | | 51 |
| Total current out of sum of all VSS ground lines (sink) | ΣIVSS | | | -160 | mA | | 51 |
| Maximum current into each VDD power line (source) | IVDD | | | 100 | mA | | 51 |
| Maximum current out of each VSS ground line (sink) | IVSS | | | -100 | mA | | 51 |
| Output current sunk by any I/O and control pin | IIO | | | 25 | mA | | 51 |
| Output current sourced by any I/O and control pin | IIO | | | -25 | mA | | 51 |
| Total output current sunk by sum of all I/O and control pins | ΣIIO | | | 120 | mA | | 51 |
| Total output current sourced by sum of all I/O and control pins | ΣIIO | | | -120 | mA | | 51 |
| Injected current on FT and TC pins | IINJ(PIN) | -5 | | 0 | mA | | 51 |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | | 25 | mA | | 51 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 51 |
| Maximum junction temperature | TJ | | | 130 | °C | | 51 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.6 | 1.68 | 1.76 | V | Falling edge | 56 |
| Power-on/power-down reset threshold | VPOR/PDR | 1.64 | 1.72 | 1.8 | V | Rising edge | 56 |
| Brownout level 1 threshold | VBOR1 | 2.13 | 2.19 | 2.24 | V | Falling edge | 56 |
| POR reset timing | TRSTTEMPO | 0.5 | 1.5 | 3 | ms | | 56 |
| VDD rise time rate | tVDD | 20 | | | µs/V | Regulator ON, upper limit unbounded | 55 |
| VDD fall time rate | tVDD | 20 | | | µs/V | Regulator ON, upper limit unbounded | 55 |
| Supply current in Run mode | IDD | | 17.7 | 20.5 | mA | External clock, all peripherals enabled, fHCLK 100 MHz, VDD=3.6 V, typ at TA=25 °C, max at TA=125 °C | 59 |
| Supply current in Standby mode | IDD_STBY | | 3.4 | 8.9 | µA | LSE and RTC ON, VDD=3.6 V, max at TA=85 °C | 70 |
| Supply current in Stop mode | IDD_STOP | | 105.6 | 385.1 | µA | Flash in Stop mode, all oscillators OFF, main regulator, VDD=1.7 V, max at TA=85 °C | 69 |
| HSI oscillator frequency | fHSI | | 16 | | MHz | | 82 |
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -8 | | 5.5 | % | TA = -40 to 125 °C | 82 |
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -4 | | 4 | % | TA = -10 to 85 °C | 82 |
| Accuracy of the HSI oscillator, factory calibrated | ACCHSI | -1 | | 1 | % | TA = 25 °C | 82 |
| HSI oscillator power consumption | IDD(HSI) | | 60 | 80 | µA | | 82 |
| LSI oscillator frequency | fLSI | 17 | 32 | 47 | kHz | VDD = 3 V, TA = -40 to 125 °C | 82 |
| PLL input clock | fPLL_IN | 0.95 | 1 | 2.1 | MHz | | 83 |
| PLL multiplier output clock | fPLL_OUT | 24 | | 100 | MHz | | 83 |
| PLL VCO output | fVCO_OUT | 100 | | 432 | MHz | | 83 |
| 48 MHz PLL multiplier output clock | fPLL48_OUT | | 48 | 75 | MHz | | 83 |
| PLL lock time | tLOCK | 75 | | 200 | µs | VCO freq = 100 MHz | 83 |
| PLL lock time | tLOCK | 100 | | 300 | µs | VCO freq = 432 MHz | 83 |
| Modulation frequency | fMod | | | 10 | kHz | SSCG | 84 |
| Peak modulation depth | md | 0.25 | | 2 | % | SSCG | 84 |
| External user clock source frequency | fHSE_ext | 1 | | 50 | MHz | | 77 |
| OSC_IN high or low time | tw(HSE) | 5 | | | ns | | 77 |
| HSE oscillator frequency | fOSC_IN | 4 | | 26 | MHz | | 80 |
## CAD (KiCad official)
- Symbol: `STM32F410RBT7`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `stm32f410rbt7-etched.step` / `stm32f410rbt7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f410rbt7.step` / `stm32f410rbt7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/stm32f410rbt7.pdf) (141 pp, sha256 `54617c5ae13d5ecf`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32f410rbt7-datasheet.pdf)