component
STM32F105RCT7
Public Made by Adomby adom
STMicroelectronics ST Microelectronics, LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
e58b5c5
STM32F105RCT7
STMicroelectronics · ST Microelectronics · LQFP-64(10x10)
STM32F105RCT7 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup supply for the RTC, the external 32 kHz oscillator and backup registers, 1.8 to 3.6 V, used through the power switch when VDD is not present. |
| 2 | PC13-TAMPER-RTC | bidirectional | General-purpose I/O (TAMPER-RTC alternate function) supplied through the power switch; in output mode it is limited to 2 MHz with a 30 pF maximum load and only one such pin may be in output mode at a time. |
| 3 | PC14-OSC32_IN | bidirectional | General-purpose I/O or OSC32_IN for the 32.768 kHz LSE oscillator; supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and one output pin at a time. |
| 4 | PC15-OSC32_OUT | bidirectional | General-purpose I/O or OSC32_OUT for the 32.768 kHz LSE oscillator; supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and one output pin at a time. |
| 5 | OSC_IN | input | External 3-25 MHz HSE oscillator input; on LQFP64 this pin is OSC_IN after reset, while the PD0 function can be remapped here by software. |
| 6 | OSC_OUT | output | External 3-25 MHz HSE oscillator output; on LQFP64 this pin is OSC_OUT after reset, while the PD1 function can be remapped here by software. |
| 7 | NRST | bidirectional | Device reset pin, listed in the pin definitions as an I/O with no alternate function. |
| 8 | PC0 | bidirectional | General-purpose I/O with ADC12_IN10 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 9 | PC1 | bidirectional | General-purpose I/O with ADC12_IN11 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 10 | PC2 | bidirectional | General-purpose I/O with ADC12_IN12 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 11 | PC3 | bidirectional | General-purpose I/O with ADC12_IN13 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 12 | VSSA | power_in | Analog ground, which must be connected to VSS. |
| 13 | VDDA | power_in | Analog supply for the ADC, reset blocks, RCs and PLL, 2.0 to 3.6 V, with a minimum of 2.4 V when the ADC is used, and it must be connected to VDD. |
| 14 | PA0-WKUP | bidirectional | General-purpose I/O with WKUP wake-up function, ADC12_IN0 analog input, and TIM2_CH1_ETR and USART2_CTS alternate functions; it is not 5 V tolerant. |
| 15 | PA1 | bidirectional | General-purpose I/O with ADC12_IN1 analog input and USART2_RTS and TIM5_CH2 alternate functions; it is not 5 V tolerant. |
| 16 | PA2 | bidirectional | General-purpose I/O with ADC12_IN2 analog input and USART2_TX and TIM5_CH3 alternate functions; it is not 5 V tolerant. |
| 17 | PA3 | bidirectional | General-purpose I/O with ADC12_IN3 analog input and USART2_RX and TIM5_CH4 alternate functions; it is not 5 V tolerant. |
| 18 | VSS_4 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 19 | VDD_4 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 20 | PA4 | bidirectional | General-purpose I/O with DAC_OUT1 output, ADC12_IN4 analog input, and SPI1_NSS, USART2_CK and SPI3_NSS/I2S3_WS alternate functions; it is not 5 V tolerant. |
| 21 | PA5 | bidirectional | General-purpose I/O with DAC_OUT2 output, ADC12_IN5 analog input, and SPI1_SCK alternate function; it is not 5 V tolerant. |
| 22 | PA6 | bidirectional | General-purpose I/O with ADC12_IN6 analog input and SPI1_MISO, TIM3_CH1 and TIM1_BKIN alternate functions; it is not 5 V tolerant. |
| 23 | PA7 | bidirectional | General-purpose I/O with ADC12_IN7 analog input and SPI1_MOSI, TIM3_CH2 and TIM1_CH1N alternate functions; it is not 5 V tolerant. |
| 24 | PC4 | bidirectional | General-purpose I/O with ADC12_IN14 analog input; it is not 5 V tolerant. |
| 25 | PC5 | bidirectional | General-purpose I/O with ADC12_IN15 analog input; it is not 5 V tolerant. |
| 26 | PB0 | bidirectional | General-purpose I/O with ADC12_IN8 analog input and TIM3_CH3 and TIM1_CH2N alternate functions; it is not 5 V tolerant. |
| 27 | PB1 | bidirectional | General-purpose I/O with ADC12_IN9 analog input and TIM3_CH4 and TIM1_CH3N alternate functions; it is not 5 V tolerant. |
| 28 | PB2/BOOT1 | bidirectional | 5 V tolerant general-purpose I/O that also serves as the BOOT1 boot-option pin sampled at startup. |
| 29 | PB10 | bidirectional | 5 V tolerant I/O with I2C2_SCL, USART3_TX and TIM2_CH3 alternate functions. |
| 30 | PB11 | bidirectional | 5 V tolerant I/O with I2C2_SDA, USART3_RX and TIM2_CH4 alternate functions. |
| 31 | VSS_1 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 32 | VDD_1 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 33 | PB12 | bidirectional | 5 V tolerant I/O with SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN and CAN2_RX alternate functions. |
| 34 | PB13 | bidirectional | 5 V tolerant I/O with SPI2_SCK/I2S2_CK, USART3_CTS, TIM1_CH1N and CAN2_TX alternate functions. |
| 35 | PB14 | bidirectional | 5 V tolerant I/O with SPI2_MISO, TIM1_CH2N and USART3_RTS alternate functions. |
| 36 | PB15 | bidirectional | 5 V tolerant I/O with SPI2_MOSI/I2S2_SD and TIM1_CH3N alternate functions. |
| 37 | PC6 | bidirectional | 5 V tolerant I/O with I2S2_MCK and TIM3_CH1 alternate functions. |
| 38 | PC7 | bidirectional | 5 V tolerant I/O with I2S3_MCK and TIM3_CH2 alternate functions. |
| 39 | PC8 | bidirectional | 5 V tolerant I/O with TIM3_CH3 alternate function. |
| 40 | PC9 | bidirectional | 5 V tolerant I/O with TIM3_CH4 alternate function. |
| 41 | PA8 | bidirectional | 5 V tolerant I/O with USART1_CK, OTG_FS_SOF, TIM1_CH1 and MCO alternate functions. |
| 42 | PA9 | bidirectional | 5 V tolerant I/O with USART1_TX, TIM1_CH2 and OTG_FS_VBUS alternate functions. |
| 43 | PA10 | bidirectional | 5 V tolerant I/O with USART1_RX, TIM1_CH3 and OTG_FS_ID alternate functions. |
| 44 | PA11 | bidirectional | 5 V tolerant I/O with USART1_CTS, CAN1_RX, TIM1_CH4 and OTG_FS_DM alternate functions. |
| 45 | PA12 | bidirectional | 5 V tolerant I/O with USART1_RTS, OTG_FS_DP, CAN1_TX and TIM1_ETR alternate functions. |
| 46 | PA13 | bidirectional | 5 V tolerant I/O which after reset is the JTMS-SWDIO serial-wire debug data pin. |
| 47 | VSS_2 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 48 | VDD_2 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 49 | PA14 | bidirectional | 5 V tolerant I/O which after reset is the JTCK-SWCLK serial-wire debug clock pin. |
| 50 | PA15 | bidirectional | 5 V tolerant I/O which after reset is JTDI, with SPI3_NSS/I2S3_WS, TIM2_CH1_ETR and SPI1_NSS alternate functions. |
| 51 | PC10 | bidirectional | 5 V tolerant I/O with UART4_TX, USART3_TX and SPI3_SCK/I2S3_CK alternate functions. |
| 52 | PC11 | bidirectional | 5 V tolerant I/O with UART4_RX, USART3_RX and SPI3_MISO alternate functions. |
| 53 | PC12 | bidirectional | 5 V tolerant I/O with UART5_TX, USART3_CK and SPI3_MOSI/I2S3_SD alternate functions. |
| 54 | PD2 | bidirectional | 5 V tolerant I/O with TIM3_ETR and UART5_RX alternate functions. |
| 55 | PB3 | bidirectional | 5 V tolerant I/O which after reset is JTDO, with SPI3_SCK/I2S3_CK, TRACESWO, TIM2_CH2 and SPI1_SCK alternate functions. |
| 56 | PB4 | bidirectional | 5 V tolerant I/O which after reset is NJTRST, with SPI3_MISO, TIM3_CH1 and SPI1_MISO alternate functions. |
| 57 | PB5 | bidirectional | I/O with I2C1_SMBA, SPI3_MOSI/I2S3_SD, TIM3_CH2, SPI1_MOSI and CAN2_RX alternate functions; it is not 5 V tolerant. |
| 58 | PB6 | bidirectional | 5 V tolerant I/O with I2C1_SCL, TIM4_CH1, USART1_TX and CAN2_TX alternate functions. |
| 59 | PB7 | bidirectional | 5 V tolerant I/O with I2C1_SDA, TIM4_CH2 and USART1_RX alternate functions. |
| 60 | BOOT0 | input | Boot selection input sampled at startup together with BOOT1 to choose boot from User Flash, System Memory or embedded SRAM. |
| 61 | PB8 | bidirectional | 5 V tolerant I/O with TIM4_CH3, I2C1_SCL and CAN1_RX alternate functions. |
| 62 | PB9 | bidirectional | 5 V tolerant I/O with TIM4_CH4, I2C1_SDA and CAN1_TX alternate functions. |
| 63 | VSS_3 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 64 | VDD_3 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage characteristics: external main supply voltage (VDD-VSS) | VDD-VSS | -0.3 | 4 | V | Including VDDA and VDD | 36 | |
| Input voltage on any other pin | VIN | 4 | V | 36 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 36 | |||
| Variations between all the different ground pins | /VSSX −VSS/ | 50 | mV | 36 | |||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 36 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 36 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 36 | |||
| Output current source by any I/Os and control pin | IIO | -25 | mA | 36 | |||
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | 0 | mA | 36 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 36 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 36 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 37 | ||
| Maximum junction temperature | TJ | 150 | °C | 37 | |||
| Internal AHB clock frequency | fHCLK | 0 | 72 | MHz | 37 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 36 | MHz | 37 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 72 | MHz | 37 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 37 | ||
| Analog operating voltage (ADC not used) | VDDA | 2 | 3.6 | V | Must be the same potential as VDD | 37 | |
| Analog operating voltage (ADC used) | VDDA | 2.4 | 3.6 | V | ADC used | 37 | |
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 37 | ||
| Power dissipation LQFP64 | PD | 444 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 37 | ||
| Ambient temperature, 7 suffix version, maximum power dissipation | TA | -40 | 105 | °C | Maximum power dissipation, 7 suffix version | 37 | |
| Ambient temperature, 7 suffix version, low power dissipation | TA | -40 | 125 | °C | Low power dissipation, 7 suffix version | 37 | |
| Junction temperature range, 7 suffix version | TJ | -40 | 125 | °C | 7 suffix version | 37 | |
| Programmable voltage detector level, rising edge | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 38 |
| Programmable voltage detector level, falling edge | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 38 |
| Programmable voltage detector level, rising edge | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 38 |
| Programmable voltage detector level, falling edge | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=111 (falling edge) | 38 |
| Power on/power down reset threshold | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 38 |
| Power on/power down reset threshold | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 38 |
| Reset temporization | TRSTTEMPO | 1 | 2.5 | 4.5 | ms | 38 | |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.26 | V | -40 °C < TA < +105 °C | 39 |
| Internal reference voltage spread over the temperature range | VRERINT | 10 | mV | VDD = 3 V | 39 | ||
| Temperature coefficient | TCoeff | 100 | ppm/°C | 39 | |||
| Supply current in Run mode, code from Flash | IDD | 68.4 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 40 | ||
| Supply current in Run mode, code from Flash | IDD | 32.9 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 40 | ||
| Supply current in Run mode, code from RAM | IDD | 66 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 40 | ||
| Supply current in Run mode, code from RAM | IDD | 31.9 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 40 | ||
| Supply current in Sleep mode | IDD | 49 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 41 | ||
| Supply current in Sleep mode | IDD | 10.6 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 41 | ||
| Supply current in Stop mode | IDD | 1300 | µA | Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog), TA = 105 °C | 41 | ||
| Supply current in Stop mode | IDD | 1280 | µA | Regulator in Low Power mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog), TA = 105 °C | 41 | ||
| Supply current in Standby mode | IDD | 6.5 | µA | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF, TA = 105 °C | 41 | ||
| Backup domain supply current | IDD_VBAT | 2.3 | µA | Low-speed oscillator and RTC ON, TA = 105 °C | 41 | ||
| External user clock source frequency (HSE) | fHSE_ext | 1 | 8 | 50 | MHz | 47 | |
| Duty cycle (HSE external clock) | DuCy(HSE) | 45 | 55 | % | 47 | ||
| Oscillator frequency (HSE crystal/ceramic resonator) | fOSC_IN | 3 | 25 | MHz | 49 | ||
| LSI oscillator frequency | fLSI | 30 | 40 | 60 | kHz | VDD = 3 V, TA = -40 to 105 °C | 52 |
| 16-bit programming time | tprog | 40 | 52.5 | 70 | µs | TA = -40 to +105 °C | 54 |
| Page (1 KB) erase time | tERASE | 20 | 40 | ms | TA = -40 to +105 °C | 54 | |
| Mass erase time | tME | 20 | 40 | ms | TA = -40 to +105 °C | 54 | |
| Supply current, Read mode | IDD | 20 | mA | fHCLK = 72 MHz with 2 wait states, VDD = 3.3 V | 54 | ||
| Supply current, Write / Erase modes | IDD | 5 | mA | fHCLK = 72 MHz, VDD = 3.3 V | 54 | ||
| Supply current, Power-down mode / Halt | IDD | 50 | µA | VDD = 3.0 to 3.6 V | 54 | ||
| Programming voltage | Vprog | 2 | 3.6 | V | 54 | ||
| Endurance | NEND | 10 | Kcycles | TA = -40 to +105 °C (7 suffix versions) | 54 | ||
| Data retention | tRET | 30 | years | 1 kcycle at TA = 85 °C | 54 | ||
| Data retention | tRET | 10 | years | 1 kcycle at TA = 105 °C | 54 | ||
| Data retention | tRET | 20 | years | 10 kcycles at TA = 55 °C | 54 | ||
| NRST Input low level voltage | VIL(NRST) | -0.5 | 0.8 | V | 62 |
CAD (KiCad official)
- Symbol:
STM32F105RCT7 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f105rct7-etched.step/stm32f105rct7-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f105rct7.step/stm32f105rct7.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (108 pp, sha256
ca4bad652e5eb36d, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32F105RCT7
**STMicroelectronics** · ST Microelectronics · LQFP-64(10x10)
STM32F105RCT7 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup supply for the RTC, the external 32 kHz oscillator and backup registers, 1.8 to 3.6 V, used through the power switch when VDD is not present. |
| 2 | PC13-TAMPER-RTC | bidirectional | General-purpose I/O (TAMPER-RTC alternate function) supplied through the power switch; in output mode it is limited to 2 MHz with a 30 pF maximum load and only one such pin may be in output mode at a time. |
| 3 | PC14-OSC32_IN | bidirectional | General-purpose I/O or OSC32_IN for the 32.768 kHz LSE oscillator; supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and one output pin at a time. |
| 4 | PC15-OSC32_OUT | bidirectional | General-purpose I/O or OSC32_OUT for the 32.768 kHz LSE oscillator; supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and one output pin at a time. |
| 5 | OSC_IN | input | External 3-25 MHz HSE oscillator input; on LQFP64 this pin is OSC_IN after reset, while the PD0 function can be remapped here by software. |
| 6 | OSC_OUT | output | External 3-25 MHz HSE oscillator output; on LQFP64 this pin is OSC_OUT after reset, while the PD1 function can be remapped here by software. |
| 7 | NRST | bidirectional | Device reset pin, listed in the pin definitions as an I/O with no alternate function. |
| 8 | PC0 | bidirectional | General-purpose I/O with ADC12_IN10 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 9 | PC1 | bidirectional | General-purpose I/O with ADC12_IN11 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 10 | PC2 | bidirectional | General-purpose I/O with ADC12_IN12 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 11 | PC3 | bidirectional | General-purpose I/O with ADC12_IN13 analog input; it is not 5 V tolerant (no FT rating in the pin table). |
| 12 | VSSA | power_in | Analog ground, which must be connected to VSS. |
| 13 | VDDA | power_in | Analog supply for the ADC, reset blocks, RCs and PLL, 2.0 to 3.6 V, with a minimum of 2.4 V when the ADC is used, and it must be connected to VDD. |
| 14 | PA0-WKUP | bidirectional | General-purpose I/O with WKUP wake-up function, ADC12_IN0 analog input, and TIM2_CH1_ETR and USART2_CTS alternate functions; it is not 5 V tolerant. |
| 15 | PA1 | bidirectional | General-purpose I/O with ADC12_IN1 analog input and USART2_RTS and TIM5_CH2 alternate functions; it is not 5 V tolerant. |
| 16 | PA2 | bidirectional | General-purpose I/O with ADC12_IN2 analog input and USART2_TX and TIM5_CH3 alternate functions; it is not 5 V tolerant. |
| 17 | PA3 | bidirectional | General-purpose I/O with ADC12_IN3 analog input and USART2_RX and TIM5_CH4 alternate functions; it is not 5 V tolerant. |
| 18 | VSS_4 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 19 | VDD_4 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 20 | PA4 | bidirectional | General-purpose I/O with DAC_OUT1 output, ADC12_IN4 analog input, and SPI1_NSS, USART2_CK and SPI3_NSS/I2S3_WS alternate functions; it is not 5 V tolerant. |
| 21 | PA5 | bidirectional | General-purpose I/O with DAC_OUT2 output, ADC12_IN5 analog input, and SPI1_SCK alternate function; it is not 5 V tolerant. |
| 22 | PA6 | bidirectional | General-purpose I/O with ADC12_IN6 analog input and SPI1_MISO, TIM3_CH1 and TIM1_BKIN alternate functions; it is not 5 V tolerant. |
| 23 | PA7 | bidirectional | General-purpose I/O with ADC12_IN7 analog input and SPI1_MOSI, TIM3_CH2 and TIM1_CH1N alternate functions; it is not 5 V tolerant. |
| 24 | PC4 | bidirectional | General-purpose I/O with ADC12_IN14 analog input; it is not 5 V tolerant. |
| 25 | PC5 | bidirectional | General-purpose I/O with ADC12_IN15 analog input; it is not 5 V tolerant. |
| 26 | PB0 | bidirectional | General-purpose I/O with ADC12_IN8 analog input and TIM3_CH3 and TIM1_CH2N alternate functions; it is not 5 V tolerant. |
| 27 | PB1 | bidirectional | General-purpose I/O with ADC12_IN9 analog input and TIM3_CH4 and TIM1_CH3N alternate functions; it is not 5 V tolerant. |
| 28 | PB2/BOOT1 | bidirectional | 5 V tolerant general-purpose I/O that also serves as the BOOT1 boot-option pin sampled at startup. |
| 29 | PB10 | bidirectional | 5 V tolerant I/O with I2C2_SCL, USART3_TX and TIM2_CH3 alternate functions. |
| 30 | PB11 | bidirectional | 5 V tolerant I/O with I2C2_SDA, USART3_RX and TIM2_CH4 alternate functions. |
| 31 | VSS_1 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 32 | VDD_1 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 33 | PB12 | bidirectional | 5 V tolerant I/O with SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN and CAN2_RX alternate functions. |
| 34 | PB13 | bidirectional | 5 V tolerant I/O with SPI2_SCK/I2S2_CK, USART3_CTS, TIM1_CH1N and CAN2_TX alternate functions. |
| 35 | PB14 | bidirectional | 5 V tolerant I/O with SPI2_MISO, TIM1_CH2N and USART3_RTS alternate functions. |
| 36 | PB15 | bidirectional | 5 V tolerant I/O with SPI2_MOSI/I2S2_SD and TIM1_CH3N alternate functions. |
| 37 | PC6 | bidirectional | 5 V tolerant I/O with I2S2_MCK and TIM3_CH1 alternate functions. |
| 38 | PC7 | bidirectional | 5 V tolerant I/O with I2S3_MCK and TIM3_CH2 alternate functions. |
| 39 | PC8 | bidirectional | 5 V tolerant I/O with TIM3_CH3 alternate function. |
| 40 | PC9 | bidirectional | 5 V tolerant I/O with TIM3_CH4 alternate function. |
| 41 | PA8 | bidirectional | 5 V tolerant I/O with USART1_CK, OTG_FS_SOF, TIM1_CH1 and MCO alternate functions. |
| 42 | PA9 | bidirectional | 5 V tolerant I/O with USART1_TX, TIM1_CH2 and OTG_FS_VBUS alternate functions. |
| 43 | PA10 | bidirectional | 5 V tolerant I/O with USART1_RX, TIM1_CH3 and OTG_FS_ID alternate functions. |
| 44 | PA11 | bidirectional | 5 V tolerant I/O with USART1_CTS, CAN1_RX, TIM1_CH4 and OTG_FS_DM alternate functions. |
| 45 | PA12 | bidirectional | 5 V tolerant I/O with USART1_RTS, OTG_FS_DP, CAN1_TX and TIM1_ETR alternate functions. |
| 46 | PA13 | bidirectional | 5 V tolerant I/O which after reset is the JTMS-SWDIO serial-wire debug data pin. |
| 47 | VSS_2 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 48 | VDD_2 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
| 49 | PA14 | bidirectional | 5 V tolerant I/O which after reset is the JTCK-SWCLK serial-wire debug clock pin. |
| 50 | PA15 | bidirectional | 5 V tolerant I/O which after reset is JTDI, with SPI3_NSS/I2S3_WS, TIM2_CH1_ETR and SPI1_NSS alternate functions. |
| 51 | PC10 | bidirectional | 5 V tolerant I/O with UART4_TX, USART3_TX and SPI3_SCK/I2S3_CK alternate functions. |
| 52 | PC11 | bidirectional | 5 V tolerant I/O with UART4_RX, USART3_RX and SPI3_MISO alternate functions. |
| 53 | PC12 | bidirectional | 5 V tolerant I/O with UART5_TX, USART3_CK and SPI3_MOSI/I2S3_SD alternate functions. |
| 54 | PD2 | bidirectional | 5 V tolerant I/O with TIM3_ETR and UART5_RX alternate functions. |
| 55 | PB3 | bidirectional | 5 V tolerant I/O which after reset is JTDO, with SPI3_SCK/I2S3_CK, TRACESWO, TIM2_CH2 and SPI1_SCK alternate functions. |
| 56 | PB4 | bidirectional | 5 V tolerant I/O which after reset is NJTRST, with SPI3_MISO, TIM3_CH1 and SPI1_MISO alternate functions. |
| 57 | PB5 | bidirectional | I/O with I2C1_SMBA, SPI3_MOSI/I2S3_SD, TIM3_CH2, SPI1_MOSI and CAN2_RX alternate functions; it is not 5 V tolerant. |
| 58 | PB6 | bidirectional | 5 V tolerant I/O with I2C1_SCL, TIM4_CH1, USART1_TX and CAN2_TX alternate functions. |
| 59 | PB7 | bidirectional | 5 V tolerant I/O with I2C1_SDA, TIM4_CH2 and USART1_RX alternate functions. |
| 60 | BOOT0 | input | Boot selection input sampled at startup together with BOOT1 to choose boot from User Flash, System Memory or embedded SRAM. |
| 61 | PB8 | bidirectional | 5 V tolerant I/O with TIM4_CH3, I2C1_SCL and CAN1_RX alternate functions. |
| 62 | PB9 | bidirectional | 5 V tolerant I/O with TIM4_CH4, I2C1_SDA and CAN1_TX alternate functions. |
| 63 | VSS_3 | power_in | Digital ground pin; all voltages are referenced to VSS. |
| 64 | VDD_3 | power_in | Digital supply for the I/Os and internal regulator, 2.0 to 3.6 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage characteristics: external main supply voltage (VDD-VSS) | VDD-VSS | -0.3 | | 4 | V | Including VDDA and VDD | 36 |
| Input voltage on any other pin | VIN | | | 4 | V | | 36 |
| Variations between different VDD power pins | /ΔVDDx/ | | | 50 | mV | | 36 |
| Variations between all the different ground pins | /VSSX −VSS/ | | | 50 | mV | | 36 |
| Total current into VDD/VDDA power lines (source) | IVDD | | | 150 | mA | | 36 |
| Total current out of VSS ground lines (sink) | IVSS | | | 150 | mA | | 36 |
| Output current sunk by any I/O and control pin | IIO | | | 25 | mA | | 36 |
| Output current source by any I/Os and control pin | IIO | -25 | | | mA | | 36 |
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | | 0 | mA | | 36 |
| Injected current on any other pin | IINJ(PIN) | -5 | | 5 | mA | | 36 |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | | 25 | mA | | 36 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 37 |
| Maximum junction temperature | TJ | | | 150 | °C | | 37 |
| Internal AHB clock frequency | fHCLK | 0 | | 72 | MHz | | 37 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 36 | MHz | | 37 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 72 | MHz | | 37 |
| Standard operating voltage | VDD | 2 | | 3.6 | V | | 37 |
| Analog operating voltage (ADC not used) | VDDA | 2 | | 3.6 | V | Must be the same potential as VDD | 37 |
| Analog operating voltage (ADC used) | VDDA | 2.4 | | 3.6 | V | ADC used | 37 |
| Backup operating voltage | VBAT | 1.8 | | 3.6 | V | | 37 |
| Power dissipation LQFP64 | PD | | | 444 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 37 |
| Ambient temperature, 7 suffix version, maximum power dissipation | TA | -40 | | 105 | °C | Maximum power dissipation, 7 suffix version | 37 |
| Ambient temperature, 7 suffix version, low power dissipation | TA | -40 | | 125 | °C | Low power dissipation, 7 suffix version | 37 |
| Junction temperature range, 7 suffix version | TJ | -40 | | 125 | °C | 7 suffix version | 37 |
| Programmable voltage detector level, rising edge | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 38 |
| Programmable voltage detector level, falling edge | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 38 |
| Programmable voltage detector level, rising edge | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 38 |
| Programmable voltage detector level, falling edge | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=111 (falling edge) | 38 |
| Power on/power down reset threshold | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 38 |
| Power on/power down reset threshold | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 38 |
| Reset temporization | TRSTTEMPO | 1 | 2.5 | 4.5 | ms | | 38 |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.26 | V | -40 °C < TA < +105 °C | 39 |
| Internal reference voltage spread over the temperature range | VRERINT | | | 10 | mV | VDD = 3 V | 39 |
| Temperature coefficient | TCoeff | | | 100 | ppm/°C | | 39 |
| Supply current in Run mode, code from Flash | IDD | | | 68.4 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 40 |
| Supply current in Run mode, code from Flash | IDD | | | 32.9 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 40 |
| Supply current in Run mode, code from RAM | IDD | | | 66 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 40 |
| Supply current in Run mode, code from RAM | IDD | | | 31.9 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 40 |
| Supply current in Sleep mode | IDD | | | 49 | mA | External clock, all peripherals enabled, fHCLK = 72 MHz, TA = 105 °C | 41 |
| Supply current in Sleep mode | IDD | | | 10.6 | mA | External clock, all peripherals disabled, fHCLK = 72 MHz, TA = 105 °C | 41 |
| Supply current in Stop mode | IDD | | | 1300 | µA | Regulator in Run mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog), TA = 105 °C | 41 |
| Supply current in Stop mode | IDD | | | 1280 | µA | Regulator in Low Power mode, low-speed and high-speed internal RC oscillators and high-speed oscillator OFF (no independent watchdog), TA = 105 °C | 41 |
| Supply current in Standby mode | IDD | | | 6.5 | µA | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF, TA = 105 °C | 41 |
| Backup domain supply current | IDD_VBAT | | | 2.3 | µA | Low-speed oscillator and RTC ON, TA = 105 °C | 41 |
| External user clock source frequency (HSE) | fHSE_ext | 1 | 8 | 50 | MHz | | 47 |
| Duty cycle (HSE external clock) | DuCy(HSE) | 45 | | 55 | % | | 47 |
| Oscillator frequency (HSE crystal/ceramic resonator) | fOSC_IN | 3 | | 25 | MHz | | 49 |
| LSI oscillator frequency | fLSI | 30 | 40 | 60 | kHz | VDD = 3 V, TA = -40 to 105 °C | 52 |
| 16-bit programming time | tprog | 40 | 52.5 | 70 | µs | TA = -40 to +105 °C | 54 |
| Page (1 KB) erase time | tERASE | 20 | | 40 | ms | TA = -40 to +105 °C | 54 |
| Mass erase time | tME | 20 | | 40 | ms | TA = -40 to +105 °C | 54 |
| Supply current, Read mode | IDD | | | 20 | mA | fHCLK = 72 MHz with 2 wait states, VDD = 3.3 V | 54 |
| Supply current, Write / Erase modes | IDD | | | 5 | mA | fHCLK = 72 MHz, VDD = 3.3 V | 54 |
| Supply current, Power-down mode / Halt | IDD | | | 50 | µA | VDD = 3.0 to 3.6 V | 54 |
| Programming voltage | Vprog | 2 | | 3.6 | V | | 54 |
| Endurance | NEND | 10 | | | Kcycles | TA = -40 to +105 °C (7 suffix versions) | 54 |
| Data retention | tRET | 30 | | | years | 1 kcycle at TA = 85 °C | 54 |
| Data retention | tRET | 10 | | | years | 1 kcycle at TA = 105 °C | 54 |
| Data retention | tRET | 20 | | | years | 10 kcycles at TA = 55 °C | 54 |
| NRST Input low level voltage | VIL(NRST) | -0.5 | | 0.8 | V | | 62 |
## CAD (KiCad official)
- Symbol: `STM32F105RCT7`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `stm32f105rct7-etched.step` / `stm32f105rct7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f105rct7.step` / `stm32f105rct7.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/content/ccc/resource/technical/document/datasheet/e4/f3/1a/89/5a/02/46/ae/CD00220364.pdf/files/CD00220364.pdf/jcr:content/translations/en.CD00220364.pdf) (108 pp, sha256 `ca4bad652e5eb36d`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32f105rct7-datasheet.pdf)