component
STM32F103RCT7
Public Made by Adomby adom
STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+100@@ -0,0 +1,100 @@+# STM32F103RCT7++**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)++STM32F103RCT7 from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBAT | power_in | Battery backup supply for RTC, external 32 kHz oscillator, and backup registers; 1.8 to 3.6 V when VDD is not present. |+| 2 | PC13-TAMPER-RTC | bidirectional | GPIO PC13 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate TAMPER-RTC function. |+| 3 | PC14-OSC32_IN | bidirectional | GPIO PC14 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate LSE 32.768 kHz oscillator input. |+| 4 | PC15-OSC32_OUT | bidirectional | GPIO PC15 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate LSE 32.768 kHz oscillator output. |+| 5 | OSC_IN | input | HSE crystal/resonator input for 4-16 MHz oscillator or 1-25 MHz external clock; PD0 (CAN_RX/FSMC_D2) software-remappable onto this pin. |+| 6 | OSC_OUT | output | HSE crystal/resonator feedback output; PD1 (CAN_TX/FSMC_D3) software-remappable onto this pin. |+| 7 | NRST | bidirectional | Active-low system reset with Schmitt trigger input and permanent 30-50 kΩ pull-up; pulses <100 ns filtered, ≥300 ns guaranteed to trigger reset. |+| 8 | PC0 | bidirectional | GPIO PC0; alternate ADC123_IN10 (analog input channel 10, shared ADC1/2/3, 0 V to VREF+ range). |+| 9 | PC1 | bidirectional | GPIO PC1; alternate ADC123_IN11 (analog input channel 11, shared ADC1/2/3). |+| 10 | PC2 | bidirectional | GPIO PC2; alternate ADC123_IN12 (analog input channel 12, shared ADC1/2/3). |+| 11 | PC3 | bidirectional | GPIO PC3; alternate ADC123_IN13 (analog input channel 13, shared ADC1/2/3). |+| 12 | VSSA | power_in | Analog ground reference for ADC, DAC, reset block, RC oscillators, and PLL; must be connected to VSS. |+| 13 | VDDA | power_in | Analog power supply for ADC, DAC, PLL, and RC oscillators; 2.0-3.6 V (minimum 2.4 V when ADC or DAC is used). |+| 14 | PA0-WKUP | bidirectional | GPIO PA0; Standby-mode wakeup pin; alternate USART2_CTS, ADC123_IN0, TIM2_CH1_ETR, TIM5_CH1, TIM8_ETR. |+| 15 | PA1 | bidirectional | GPIO PA1; alternate USART2_RTS, ADC123_IN1, TIM5_CH2, TIM2_CH2. |+| 16 | PA2 | bidirectional | GPIO PA2; alternate USART2_TX, TIM5_CH3, ADC123_IN2, TIM2_CH3. |+| 17 | PA3 | bidirectional | GPIO PA3; alternate USART2_RX, TIM5_CH4, ADC123_IN3, TIM2_CH4. |+| 18 | VSS_4 | power_in | Digital ground supply pin (VSS_4); must be connected to system ground. |+| 19 | VDD_4 | power_in | Main digital I/O and internal regulator supply (VDD_4); 2.0 to 3.6 V. |+| 20 | PA4 | bidirectional | GPIO PA4; alternate SPI1_NSS, USART2_CK, DAC_OUT1, ADC12_IN4. |+| 21 | PA5 | bidirectional | GPIO PA5; alternate SPI1_SCK, DAC_OUT2, ADC12_IN5. |+| 22 | PA6 | bidirectional | GPIO PA6; alternate SPI1_MISO, TIM8_BKIN, ADC12_IN6; remap TIM3_CH1, TIM1_BKIN. |+| 23 | PA7 | bidirectional | GPIO PA7; alternate SPI1_MOSI, TIM8_CH1N, ADC12_IN7; remap TIM3_CH2, TIM1_CH1N. |+| 24 | PC4 | bidirectional | GPIO PC4; alternate ADC12_IN14 (analog input channel 14, shared ADC1/2). |+| 25 | PC5 | bidirectional | GPIO PC5; alternate ADC12_IN15 (analog input channel 15, shared ADC1/2). |+| 26 | PB0 | bidirectional | GPIO PB0; alternate ADC12_IN8, TIM3_CH3, TIM8_CH2N; remap TIM1_CH2N. |+| 27 | PB1 | bidirectional | GPIO PB1; alternate ADC12_IN9, TIM3_CH4, TIM8_CH3N; remap TIM1_CH3N. |+| 28 | PB2 | bidirectional | 5 V-tolerant GPIO PB2; dual-function as BOOT1 boot configuration pin sampled at reset. |+| 29 | PB10 | bidirectional | 5 V-tolerant GPIO PB10; alternate I2C2_SCL, USART3_TX; remap TIM2_CH3. |+| 30 | PB11 | bidirectional | 5 V-tolerant GPIO PB11; alternate I2C2_SDA, USART3_RX; remap TIM2_CH4. |+| 31 | VSS_1 | power_in | Digital ground supply pin (VSS_1); must be connected to system ground. |+| 32 | VDD_1 | power_in | Main digital I/O and internal regulator supply (VDD_1); 2.0 to 3.6 V. |+| 33 | PB12 | bidirectional | 5 V-tolerant GPIO PB12; alternate SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN. |+| 34 | PB13 | bidirectional | 5 V-tolerant GPIO PB13; alternate SPI2_SCK/I2S2_CK, USART3_CTS, TIM1_CH1N. |+| 35 | PB14 | bidirectional | 5 V-tolerant GPIO PB14; alternate SPI2_MISO, TIM1_CH2N; remap USART3_RTS. |+| 36 | PB15 | bidirectional | 5 V-tolerant GPIO PB15; alternate SPI2_MOSI/I2S2_SD; remap TIM1_CH3N. |+| 37 | PC6 | bidirectional | 5 V-tolerant GPIO PC6; alternate I2S2_MCK, TIM8_CH1, SDIO_D6; remap TIM3_CH1. |+| 38 | PC7 | bidirectional | 5 V-tolerant GPIO PC7; alternate I2S3_MCK, TIM8_CH2, SDIO_D7; remap TIM3_CH2. |+| 39 | PC8 | bidirectional | 5 V-tolerant GPIO PC8; alternate TIM8_CH3, SDIO_D0; remap TIM3_CH3. |+| 40 | PC9 | bidirectional | 5 V-tolerant GPIO PC9; alternate TIM8_CH4, SDIO_D1; remap TIM3_CH4. |+| 41 | PA8 | bidirectional | 5 V-tolerant GPIO PA8; alternate USART1_CK, TIM1_CH1, MCO (microcontroller clock output). |+| 42 | PA9 | bidirectional | 5 V-tolerant GPIO PA9; alternate USART1_TX (up to 4.5 Mbit/s), TIM1_CH2. |+| 43 | PA10 | bidirectional | 5 V-tolerant GPIO PA10; alternate USART1_RX, TIM1_CH3. |+| 44 | PA11 | bidirectional | 5 V-tolerant GPIO PA11; alternate USART1_CTS, USB_DM (USB full-speed D−), CAN_RX, TIM1_CH4. |+| 45 | PA12 | bidirectional | 5 V-tolerant GPIO PA12; alternate USART1_RTS, USB_DP (USB full-speed D+), CAN_TX, TIM1_ETR. |+| 46 | PA13 | bidirectional | 5 V-tolerant GPIO PA13; default JTMS-SWDIO (JTAG TMS / SWD bidirectional data); remappable to PA13 GPIO. |+| 47 | VSS_2 | power_in | Digital ground supply pin (VSS_2); must be connected to system ground. |+| 48 | VDD_2 | power_in | Main digital I/O and internal regulator supply (VDD_2); 2.0 to 3.6 V. |+| 49 | PA14 | bidirectional | 5 V-tolerant GPIO PA14; default JTCK-SWCLK (JTAG TCK / SWD clock); remappable to PA14 GPIO. |+| 50 | PA15 | bidirectional | 5 V-tolerant GPIO PA15; default JTDI; remap SPI3_NSS/I2S3_WS, TIM2_CH1_ETR, SPI1_NSS. |+| 51 | PC10 | bidirectional | 5 V-tolerant GPIO PC10; alternate UART4_TX, SDIO_D2; remap USART3_TX. |+| 52 | PC11 | bidirectional | 5 V-tolerant GPIO PC11; alternate UART4_RX, SDIO_D3; remap USART3_RX. |+| 53 | PC12 | bidirectional | 5 V-tolerant GPIO PC12; alternate UART5_TX, SDIO_CK; remap USART3_CK. |+| 54 | PD2 | bidirectional | 5 V-tolerant GPIO PD2; alternate TIM3_ETR, UART5_RX, SDIO_CMD. |+| 55 | PB3 | bidirectional | 5 V-tolerant GPIO PB3; default JTDO; remap SPI3_SCK/I2S3_CK, TIM2_CH2, SPI1_SCK, TRACESWO. |+| 56 | PB4 | bidirectional | 5 V-tolerant GPIO PB4; default NJTRST (JTAG reset); remap SPI3_MISO, TIM3_CH1, SPI1_MISO. |+| 57 | PB5 | bidirectional | GPIO PB5 (not 5 V-tolerant); alternate I2C1_SMBA, SPI3_MOSI/I2S3_SD; remap TIM3_CH2, SPI1_MOSI. |+| 58 | PB6 | bidirectional | 5 V-tolerant GPIO PB6; alternate I2C1_SCL, TIM4_CH1; remap USART1_TX. |+| 59 | PB7 | bidirectional | 5 V-tolerant GPIO PB7; alternate I2C1_SDA, FSMC_NADV, TIM4_CH2; remap USART1_RX. |+| 60 | BOOT0 | input | Boot mode select pin sampled at reset; high combined with BOOT1 state selects system-memory or SRAM boot; pull low for normal Flash boot. |+| 61 | PB8 | bidirectional | 5 V-tolerant GPIO PB8; alternate TIM4_CH3, SDIO_D4; remap I2C1_SCL, CAN_RX. |+| 62 | PB9 | bidirectional | 5 V-tolerant GPIO PB9; alternate TIM4_CH4, SDIO_D5; remap I2C1_SDA, CAN_TX. |+| 63 | VSS_3 | power_in | Digital ground supply pin (VSS_3); must be connected to system ground. |+| 64 | VDD_3 | power_in | Main digital I/O and internal regulator supply (VDD_3); 2.0 to 3.6 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LQFP-64(10x10) |+| Category | Embedded Processors & Controllers |+| Pins | 64 |++## CAD (KiCad official)++- Symbol: `STM32F103RCT7`+- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`+- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)+- 3D model files: `stm32f103rct7-etched.step` / `stm32f103rct7-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f103rct7.step` / `stm32f103rct7.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893086768640000) (143 pp, sha256 `c61db5e362b62f2f`, retrieved 2026-09-26, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stm32f103rct7-datasheet.pdf)
page.jsonadded+493@@ -0,0 +1,493 @@+{+ "slug": "stm32f103rct7",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "embedded processors & controllers",+ "stm32f103rct7",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "stm32f103rct7.kicad_sym",+ "stm32f103rct7.kicad_mod",+ "stm32f103rct7.glb",+ "stm32f103rct7.step",+ "stm32f103rct7.lbr",+ "docs/hero.png",+ "docs/stm32f103rct7-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "STM32F103RCT7",+ "manufacturer": "STMicroelectronics",+ "package": "LQFP-64(10x10)",+ "pin_count": 64,+ "category": "Embedded Processors & Controllers",+ "subcategory": "Microcontrollers (MCU/MPU/SOC)",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893086768640000",+ "parts": {+ "symbol": "stm32f103rct7.kicad_sym",+ "footprint": "stm32f103rct7.kicad_mod",+ "model_3d": "stm32f103rct7-etched.glb",+ "model_3d_plain": "stm32f103rct7.glb",+ "model_3d_step": "stm32f103rct7-etched.step",+ "model_3d_step_plain": "stm32f103rct7.step",+ "lbr": "stm32f103rct7.lbr"+ },+ "distributor_links": {+ "lcsc": "C882165",+ "digikey": "497-11527-ND",+ "mouser": "511-STM32F103RCT7"+ },+ "distributor_check": {+ "checked_at": "2026-09-26T16:37:46Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-11527-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "511-STM32F103RCT7",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "VBAT",+ "type": "power_in",+ "description": "Battery backup supply for RTC, external 32 kHz oscillator, and backup registers; 1.8 to 3.6 V when VDD is not present."+ },+ {+ "number": "2",+ "name": "PC13-TAMPER-RTC",+ "type": "bidirectional",+ "description": "GPIO PC13 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate TAMPER-RTC function."+ },+ {+ "number": "3",+ "name": "PC14-OSC32_IN",+ "type": "bidirectional",+ "description": "GPIO PC14 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate LSE 32.768 kHz oscillator input."+ },+ {+ "number": "4",+ "name": "PC15-OSC32_OUT",+ "type": "bidirectional",+ "description": "GPIO PC15 supplied through power switch; limited to ≤3 mA, ≤2 MHz, 30 pF max load; alternate LSE 32.768 kHz oscillator output."+ },+ {+ "number": "5",+ "name": "OSC_IN",+ "type": "input",+ "description": "HSE crystal/resonator input for 4-16 MHz oscillator or 1-25 MHz external clock; PD0 (CAN_RX/FSMC_D2) software-remappable onto this pin."+ },+ {+ "number": "6",+ "name": "OSC_OUT",+ "type": "output",+ "description": "HSE crystal/resonator feedback output; PD1 (CAN_TX/FSMC_D3) software-remappable onto this pin."+ },+ {+ "number": "7",+ "name": "NRST",+ "type": "bidirectional",+ "description": "Active-low system reset with Schmitt trigger input and permanent 30-50 kΩ pull-up; pulses <100 ns filtered, ≥300 ns guaranteed to trigger reset."+ },+ {+ "number": "8",+ "name": "PC0",+ "type": "bidirectional",+ "description": "GPIO PC0; alternate ADC123_IN10 (analog input channel 10, shared ADC1/2/3, 0 V to VREF+ range)."+ },+ {+ "number": "9",+ "name": "PC1",+ "type": "bidirectional",+ "description": "GPIO PC1; alternate ADC123_IN11 (analog input channel 11, shared ADC1/2/3)."+ },+ {+ "number": "10",+ "name": "PC2",+ "type": "bidirectional",+ "description": "GPIO PC2; alternate ADC123_IN12 (analog input channel 12, shared ADC1/2/3)."+ },+ {+ "number": "11",+ "name": "PC3",+ "type": "bidirectional",+ "description": "GPIO PC3; alternate ADC123_IN13 (analog input channel 13, shared ADC1/2/3)."+ },+ {+ "number": "12",+ "name": "VSSA",+ "type": "power_in",+ "description": "Analog ground reference for ADC, DAC, reset block, RC oscillators, and PLL; must be connected to VSS."+ },+ {+ "number": "13",+ "name": "VDDA",+ "type": "power_in",+ "description": "Analog power supply for ADC, DAC, PLL, and RC oscillators; 2.0-3.6 V (minimum 2.4 V when ADC or DAC is used)."+ },+ {+ "number": "14",+ "name": "PA0-WKUP",+ "type": "bidirectional",+ "description": "GPIO PA0; Standby-mode wakeup pin; alternate USART2_CTS, ADC123_IN0, TIM2_CH1_ETR, TIM5_CH1, TIM8_ETR."+ },+ {+ "number": "15",+ "name": "PA1",+ "type": "bidirectional",+ "description": "GPIO PA1; alternate USART2_RTS, ADC123_IN1, TIM5_CH2, TIM2_CH2."+ },+ {+ "number": "16",+ "name": "PA2",+ "type": "bidirectional",+ "description": "GPIO PA2; alternate USART2_TX, TIM5_CH3, ADC123_IN2, TIM2_CH3."+ },+ {+ "number": "17",+ "name": "PA3",+ "type": "bidirectional",+ "description": "GPIO PA3; alternate USART2_RX, TIM5_CH4, ADC123_IN3, TIM2_CH4."+ },+ {+ "number": "18",+ "name": "VSS_4",+ "type": "power_in",+ "description": "Digital ground supply pin (VSS_4); must be connected to system ground."+ },+ {+ "number": "19",+ "name": "VDD_4",+ "type": "power_in",+ "description": "Main digital I/O and internal regulator supply (VDD_4); 2.0 to 3.6 V."+ },+ {+ "number": "20",+ "name": "PA4",+ "type": "bidirectional",+ "description": "GPIO PA4; alternate SPI1_NSS, USART2_CK, DAC_OUT1, ADC12_IN4."+ },+ {+ "number": "21",+ "name": "PA5",+ "type": "bidirectional",+ "description": "GPIO PA5; alternate SPI1_SCK, DAC_OUT2, ADC12_IN5."+ },+ {+ "number": "22",+ "name": "PA6",+ "type": "bidirectional",+ "description": "GPIO PA6; alternate SPI1_MISO, TIM8_BKIN, ADC12_IN6; remap TIM3_CH1, TIM1_BKIN."+ },+ {+ "number": "23",+ "name": "PA7",+ "type": "bidirectional",+ "description": "GPIO PA7; alternate SPI1_MOSI, TIM8_CH1N, ADC12_IN7; remap TIM3_CH2, TIM1_CH1N."+ },+ {+ "number": "24",+ "name": "PC4",+ "type": "bidirectional",+ "description": "GPIO PC4; alternate ADC12_IN14 (analog input channel 14, shared ADC1/2)."+ },+ {+ "number": "25",+ "name": "PC5",+ "type": "bidirectional",+ "description": "GPIO PC5; alternate ADC12_IN15 (analog input channel 15, shared ADC1/2)."+ },+ {+ "number": "26",+ "name": "PB0",+ "type": "bidirectional",+ "description": "GPIO PB0; alternate ADC12_IN8, TIM3_CH3, TIM8_CH2N; remap TIM1_CH2N."+ },+ {+ "number": "27",+ "name": "PB1",+ "type": "bidirectional",+ "description": "GPIO PB1; alternate ADC12_IN9, TIM3_CH4, TIM8_CH3N; remap TIM1_CH3N."+ },+ {+ "number": "28",+ "name": "PB2",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB2; dual-function as BOOT1 boot configuration pin sampled at reset."+ },+ {+ "number": "29",+ "name": "PB10",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB10; alternate I2C2_SCL, USART3_TX; remap TIM2_CH3."+ },+ {+ "number": "30",+ "name": "PB11",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB11; alternate I2C2_SDA, USART3_RX; remap TIM2_CH4."+ },+ {+ "number": "31",+ "name": "VSS_1",+ "type": "power_in",+ "description": "Digital ground supply pin (VSS_1); must be connected to system ground."+ },+ {+ "number": "32",+ "name": "VDD_1",+ "type": "power_in",+ "description": "Main digital I/O and internal regulator supply (VDD_1); 2.0 to 3.6 V."+ },+ {+ "number": "33",+ "name": "PB12",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB12; alternate SPI2_NSS/I2S2_WS, I2C2_SMBA, USART3_CK, TIM1_BKIN."+ },+ {+ "number": "34",+ "name": "PB13",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB13; alternate SPI2_SCK/I2S2_CK, USART3_CTS, TIM1_CH1N."+ },+ {+ "number": "35",+ "name": "PB14",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB14; alternate SPI2_MISO, TIM1_CH2N; remap USART3_RTS."+ },+ {+ "number": "36",+ "name": "PB15",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB15; alternate SPI2_MOSI/I2S2_SD; remap TIM1_CH3N."+ },+ {+ "number": "37",+ "name": "PC6",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC6; alternate I2S2_MCK, TIM8_CH1, SDIO_D6; remap TIM3_CH1."+ },+ {+ "number": "38",+ "name": "PC7",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC7; alternate I2S3_MCK, TIM8_CH2, SDIO_D7; remap TIM3_CH2."+ },+ {+ "number": "39",+ "name": "PC8",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC8; alternate TIM8_CH3, SDIO_D0; remap TIM3_CH3."+ },+ {+ "number": "40",+ "name": "PC9",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC9; alternate TIM8_CH4, SDIO_D1; remap TIM3_CH4."+ },+ {+ "number": "41",+ "name": "PA8",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA8; alternate USART1_CK, TIM1_CH1, MCO (microcontroller clock output)."+ },+ {+ "number": "42",+ "name": "PA9",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA9; alternate USART1_TX (up to 4.5 Mbit/s), TIM1_CH2."+ },+ {+ "number": "43",+ "name": "PA10",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA10; alternate USART1_RX, TIM1_CH3."+ },+ {+ "number": "44",+ "name": "PA11",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA11; alternate USART1_CTS, USB_DM (USB full-speed D−), CAN_RX, TIM1_CH4."+ },+ {+ "number": "45",+ "name": "PA12",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA12; alternate USART1_RTS, USB_DP (USB full-speed D+), CAN_TX, TIM1_ETR."+ },+ {+ "number": "46",+ "name": "PA13",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA13; default JTMS-SWDIO (JTAG TMS / SWD bidirectional data); remappable to PA13 GPIO."+ },+ {+ "number": "47",+ "name": "VSS_2",+ "type": "power_in",+ "description": "Digital ground supply pin (VSS_2); must be connected to system ground."+ },+ {+ "number": "48",+ "name": "VDD_2",+ "type": "power_in",+ "description": "Main digital I/O and internal regulator supply (VDD_2); 2.0 to 3.6 V."+ },+ {+ "number": "49",+ "name": "PA14",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA14; default JTCK-SWCLK (JTAG TCK / SWD clock); remappable to PA14 GPIO."+ },+ {+ "number": "50",+ "name": "PA15",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PA15; default JTDI; remap SPI3_NSS/I2S3_WS, TIM2_CH1_ETR, SPI1_NSS."+ },+ {+ "number": "51",+ "name": "PC10",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC10; alternate UART4_TX, SDIO_D2; remap USART3_TX."+ },+ {+ "number": "52",+ "name": "PC11",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC11; alternate UART4_RX, SDIO_D3; remap USART3_RX."+ },+ {+ "number": "53",+ "name": "PC12",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PC12; alternate UART5_TX, SDIO_CK; remap USART3_CK."+ },+ {+ "number": "54",+ "name": "PD2",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PD2; alternate TIM3_ETR, UART5_RX, SDIO_CMD."+ },+ {+ "number": "55",+ "name": "PB3",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB3; default JTDO; remap SPI3_SCK/I2S3_CK, TIM2_CH2, SPI1_SCK, TRACESWO."+ },+ {+ "number": "56",+ "name": "PB4",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB4; default NJTRST (JTAG reset); remap SPI3_MISO, TIM3_CH1, SPI1_MISO."+ },+ {+ "number": "57",+ "name": "PB5",+ "type": "bidirectional",+ "description": "GPIO PB5 (not 5 V-tolerant); alternate I2C1_SMBA, SPI3_MOSI/I2S3_SD; remap TIM3_CH2, SPI1_MOSI."+ },+ {+ "number": "58",+ "name": "PB6",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB6; alternate I2C1_SCL, TIM4_CH1; remap USART1_TX."+ },+ {+ "number": "59",+ "name": "PB7",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB7; alternate I2C1_SDA, FSMC_NADV, TIM4_CH2; remap USART1_RX."+ },+ {+ "number": "60",+ "name": "BOOT0",+ "type": "input",+ "description": "Boot mode select pin sampled at reset; high combined with BOOT1 state selects system-memory or SRAM boot; pull low for normal Flash boot."+ },+ {+ "number": "61",+ "name": "PB8",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB8; alternate TIM4_CH3, SDIO_D4; remap I2C1_SCL, CAN_RX."+ },+ {+ "number": "62",+ "name": "PB9",+ "type": "bidirectional",+ "description": "5 V-tolerant GPIO PB9; alternate TIM4_CH4, SDIO_D5; remap I2C1_SDA, CAN_TX."+ },+ {+ "number": "63",+ "name": "VSS_3",+ "type": "power_in",+ "description": "Digital ground supply pin (VSS_3); must be connected to system ground."+ },+ {+ "number": "64",+ "name": "VDD_3",+ "type": "power_in",+ "description": "Main digital I/O and internal regulator supply (VDD_3); 2.0 to 3.6 V."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-4-6",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The complex table structure with multiple package variants made pin extraction challenging. Pins 5-6; LQFP64 package excludes many GPIO ports (E, F, G) available in LQFP100/144. This device is constrain"+ ],+ "pages_sent": 143,+ "cost_usd": 1.7274,+ "at": "2026-09-26T16:37:19"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893086768640000",+ "pages": 143,+ "sha256": "c61db5e362b62f2f",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 64,+ "described": 64,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}