Generated by kicad-footprint-generator · KiCad file format 20260206
STM32F103C6U6A
STMicroelectronics · Microcontrollers (MCU/MPU/SOC) · QFN-48-EP(7x7)
STM32F103C6U6A from STMicroelectronics, in a QFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply for the RTC, 32 kHz oscillator and backup registers when VDD is not present, 1.8 to 3.6 V. |
| 2 | PC13-TAMPER-RTC | bidirectional | General-purpose I/O supplied through the power switch (sink/source limited to 3 mA); output speed must not exceed 2 MHz with 30 pF maximum load and it must not be used as a current source; alternate function TAMPER-RTC. |
| 3 | PC14-OSC32_IN | bidirectional | General-purpose I/O supplied through the power switch with the same 3 mA and 2 MHz / 30 pF limits as PC13; alternate function OSC32_IN for the 32.768 kHz oscillator input. |
| 4 | PC15-OSC32_OUT | bidirectional | General-purpose I/O supplied through the power switch with the same 3 mA and 2 MHz / 30 pF limits as PC13; alternate function OSC32_OUT for the 32.768 kHz oscillator output. |
| 5 | OSC_IN | input | HSE oscillator input for a 4 to 16 MHz crystal/resonator, or external clock input of 1 to 25 MHz with VIH at least 0.7 VDD; defaults to OSC_IN after reset and can be remapped to PD0. |
| 6 | OSC_OUT | output | HSE oscillator output to the crystal/resonator; defaults to OSC_OUT after reset and can be remapped to PD1. |
| 7 | NRST | bidirectional | Active-low reset pin with CMOS input (VIL max 0.8 V, VIH min 2 V), internal pull-up of 30 to 50 kΩ, filtering pulses shorter than 100 ns. |
| 8 | VSSA | power_in | Analog ground for ADC, reset blocks, RCs and PLL; must be connected to VSS. |
| 9 | VDDA | power_in | Analog supply for ADC, reset blocks, RCs and PLL, 2.0 to 3.6 V (minimum 2.4 V when the ADC is used); must be at the same potential as VDD. |
| 10 | PA0-WKUP | bidirectional | Standard I/O with WKUP wake-up function; alternate functions USART2_CTS, ADC12_IN0 and TIM2_CH1_ETR. |
| 11 | PA1 | bidirectional | Standard I/O; alternate functions USART2_RTS, ADC12_IN1 and TIM2_CH2. |
| 12 | PA2 | bidirectional | Standard I/O; alternate functions USART2_TX, ADC12_IN2 and TIM2_CH3. |
| 13 | PA3 | bidirectional | Standard I/O; alternate functions USART2_RX, ADC12_IN3 and TIM2_CH4. |
| 14 | PA4 | bidirectional | Standard I/O; alternate functions SPI1_NSS, USART2_CK and ADC12_IN4. |
| 15 | PA5 | bidirectional | Standard I/O; alternate functions SPI1_SCK and ADC12_IN5. |
| 16 | PA6 | bidirectional | Standard I/O; alternate functions SPI1_MISO, ADC12_IN6 and TIM3_CH1 (TIM1_BKIN on remap). |
| 17 | PA7 | bidirectional | Standard I/O; alternate functions SPI1_MOSI, ADC12_IN7 and TIM3_CH2 (TIM1_CH1N on remap). |
| 18 | PB0 | bidirectional | Standard I/O; alternate functions ADC12_IN8 and TIM3_CH3 (TIM1_CH2N on remap). |
| 19 | PB1 | bidirectional | Standard I/O; alternate functions ADC12_IN9 and TIM3_CH4 (TIM1_CH3N on remap). |
| 20 | PB2/BOOT1 | bidirectional | 5 V-tolerant I/O (FT) that also latches the BOOT1 boot-mode level at startup. |
| 21 | PB10 | bidirectional | 5 V-tolerant I/O (FT); remap alternate function TIM2_CH3. |
| 22 | PB11 | bidirectional | 5 V-tolerant I/O (FT); remap alternate function TIM2_CH4. |
| 23 | VSS_1 | power_in | Digital ground. |
| 24 | VDD_1 | power_in | Digital supply for I/Os and internal regulator, 2.0 to 3.6 V. |
| 25 | PB12 | bidirectional | 5 V-tolerant I/O (FT); alternate function TIM1_BKIN. |
| 26 | PB13 | bidirectional | 5 V-tolerant I/O (FT); alternate function TIM1_CH1N. |
| 27 | PB14 | bidirectional | 5 V-tolerant I/O (FT); alternate function TIM1_CH2N. |
| 28 | PB15 | bidirectional | 5 V-tolerant I/O (FT); alternate function TIM1_CH3N. |
| 29 | PA8 | bidirectional | 5 V-tolerant I/O (FT); alternate functions USART1_CK, TIM1_CH1 and MCO. |
| 30 | PA9 | bidirectional | 5 V-tolerant I/O (FT); alternate functions USART1_TX and TIM1_CH2. |
| 31 | PA10 | bidirectional | 5 V-tolerant I/O (FT); alternate functions USART1_RX and TIM1_CH3. |
| 32 | PA11 | bidirectional | 5 V-tolerant I/O (FT); alternate functions USART1_CTS, CAN_RX, TIM1_CH4 and USBDM. |
| 33 | PA12 | bidirectional | 5 V-tolerant I/O (FT); alternate functions USART1_RTS, CAN_TX, TIM1_ETR and USBDP. |
| 34 | PA13 | bidirectional | 5 V-tolerant I/O (FT); alternate function JTMS/SWDIO (SWD debug). |
| 35 | VSS_2 | power_in | Digital ground. |
| 36 | VDD_2 | power_in | Digital supply for I/Os and internal regulator, 2.0 to 3.6 V. |
| 37 | PA14 | bidirectional | 5 V-tolerant I/O (FT); alternate function JTCK/SWCLK (SWD debug). |
| 38 | PA15 | bidirectional | 5 V-tolerant I/O (FT); alternate function JTDI, with remap TIM2_CH1_ETR and SPI1_NSS. |
| 39 | PB3 | bidirectional | 5 V-tolerant I/O (FT); alternate function JTDO, with remap TIM2_CH2 and TRACESWO. |
| 40 | PB4 | bidirectional | 5 V-tolerant I/O (FT); alternate function NJTRST, with remap TIM3_CH1 and SPI1_MISO. |
| 41 | PB5 | bidirectional | Standard I/O (not 5 V-tolerant); alternate function I2C1_SMBA, with remap TIM3_CH2 and SPI1_MOSI. |
| 42 | PB6 | bidirectional | 5 V-tolerant I/O (FT); alternate functions I2C1_SCL and USART1_TX. |
| 43 | PB7 | bidirectional | 5 V-tolerant I/O (FT); alternate functions I2C1_SDA and USART1_RX. |
| 44 | BOOT0 | input | Boot mode selection input, valid range 0 to 5.5 V. |
| 45 | PB8 | bidirectional | 5 V-tolerant I/O (FT); alternate functions I2C1_SCL and CAN_RX. |
| 46 | PB9 | bidirectional | 5 V-tolerant I/O (FT); alternate functions I2C1_SDA and CAN_TX. |
| 47 | VSS_3 | power_in | Digital ground. |
| 48 | VDD_3 | power_in | Digital supply for I/Os and internal regulator, 2.0 to 3.6 V. |
| 49 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | QFN-48-EP(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD − VSS | -0.3 | 4 | V | 32 | ||
| Input voltage on any other pin | VIN | 4 | V | 32 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 32 | |||
| Variations between all the different ground pins | /VSSX −VSS/ | 50 | mV | 32 | |||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 33 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 33 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 33 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 33 | |||
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | 0 | mA | 33 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 33 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 33 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 33 | ||
| Maximum junction temperature | TJ | 150 | °C | 33 | |||
| Internal AHB clock frequency | fHCLK | 0 | 72 | MHz | 33 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 36 | MHz | 33 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 72 | MHz | 33 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 33 | ||
| Analog operating voltage | VDDA | 2 | 3.6 | V | ADC not used; must be the same potential as VDD | 33 | |
| Analog operating voltage | VDDA | 2.4 | 3.6 | V | ADC used | 33 | |
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 33 | ||
| I/O input voltage, five volt tolerant (FT) pins | VIN | -0.3 | 5.5 | V | 2 V < VDD ≤ 3.6 V | 34 | |
| I/O input voltage, five volt tolerant (FT) pins | VIN | -0.3 | 5.2 | V | VDD = 2 V | 34 | |
| BOOT0 input voltage | VIN | 0 | 5.5 | V | 34 | ||
| Power dissipation, UFQFPN48 package | PD | 624 | mW | TA = 85 °C for suffix 6 | 34 | ||
| Ambient temperature for 6 suffix version | TA | -40 | 85 | °C | Maximum power dissipation | 34 | |
| Ambient temperature for 6 suffix version | TA | -40 | 105 | °C | Low power dissipation | 34 | |
| Junction temperature range, 6 suffix version | TJ | -40 | 105 | °C | 34 | ||
| VDD rise time rate | tVDD | 0 | µs/V | 34 | |||
| VDD fall time rate | tVDD | 20 | µs/V | 34 | |||
| Programmable voltage detector level selection | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.19 | 2.28 | 2.37 | V | PLS[2:0]=001 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.09 | 2.18 | 2.27 | V | PLS[2:0]=001 (falling edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.28 | 2.38 | 2.48 | V | PLS[2:0]=010 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.18 | 2.28 | 2.38 | V | PLS[2:0]=010 (falling edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.38 | 2.48 | 2.58 | V | PLS[2:0]=011 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.47 | 2.58 | 2.69 | V | PLS[2:0]=100 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.37 | 2.48 | 2.59 | V | PLS[2:0]=100 (falling edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.57 | 2.68 | 2.79 | V | PLS[2:0]=101 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=110 (rising edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.56 | 2.68 | 2.8 | V | PLS[2:0]=110 (falling edge) | 35 |
| Programmable voltage detector level selection | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 35 |
| Power on/power down reset threshold | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 35 |
| Power on/power down reset threshold | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 35 |
| Reset temporization | TRSTTEMPO | 1 | 2.5 | 4.5 | ms | 35 | |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.24 | V | -40 °C < TA < +85 °C | 36 |
| Internal reference voltage spread over the temperature range | VRERINT | 10 | mV | VDD = 3 V ±10 mV | 36 | ||
| Temperature coefficient of internal reference voltage | TCoeff | 100 | ppm/°C | 36 | |||
| Supply current in Stop mode | IDD | 160 | µA | Regulator in Run mode, LSI/HSI RC and HSE OFF (no independent watchdog) | 40 | ||
| Supply current in Stop mode | IDD | 145 | µA | Regulator in Low Power mode, LSI/HSI RC and HSE OFF (no independent watchdog) | 40 | ||
| Supply current in Standby mode | IDD | 3.2 | µA | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF | 40 | ||
| Backup domain supply current | IDD_VBAT | 1.9 | µA | Low-speed oscillator and RTC ON | 40 | ||
| Supply current in Run mode | IDD | 45 | mA | External clock, all peripherals enabled; fHCLK 72 MHz; TA = 85 °C; code from Flash | 37 | ||
| HSE oscillator frequency | fOSC_IN | 4 | 8 | 16 | MHz | 48 | |
| Accuracy of the HSI oscillator, factory-calibrated | ACCHSI | -1.5 | 2.2 | % | TA = -10 to 85 °C | 50 | |
| LSI oscillator frequency | fLSI | 30 | 40 | 60 | kHz | VDD = 3 V, TA = -40 to 105 °C (table note) | 51 |
| PLL input clock | fPLL_IN | 1 | 8 | 25 | MHz | 52 |
CAD (KiCad official)
- Symbol:
STM32F103C6U6A - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: QFN-48-EP(7x7), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.55 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
stm32f103c6u6a-etched.step/stm32f103c6u6a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f103c6u6a.step/stm32f103c6u6a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (99 pp, sha256
31ab1fe3de6e6cf3, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).