component
STM32F100RBT6BTR
Public Made by Adomby adom
STMicroelectronics ST Microelectronics, LQFP-64(10x10). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
2f8806a
STM32F100RBT6BTR
STMicroelectronics · ST Microelectronics · LQFP-64(10x10)
STM32F100RBT6BTR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input for the RTC and backup registers, as stated in the VBAT supply feature. |
| 2 | PC13-TAMPER-RTC | bidirectional | GPIO PC13 (also TAMPER-RTC); it is supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as LED drive. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO PC14 (also OSC32_IN for the 32.768 kHz oscillator); it is supplied through the power switch with the same 3 mA sink limit and 2 MHz / 30 pF output restriction. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO PC15 (also OSC32_OUT for the 32.768 kHz oscillator); it is supplied through the power switch with the same 3 mA sink limit and 2 MHz / 30 pF output restriction. |
| 5 | OSC_IN | input | HSE 4-24 MHz crystal oscillator input, configured as OSC_IN after reset; PD0 can be remapped onto this pin by software. |
| 6 | OSC_OUT | output | HSE 4-24 MHz crystal oscillator output, configured as OSC_OUT after reset; PD1 can be remapped onto this pin by software. |
| 7 | NRST | bidirectional | Device reset pin (active low); its electrical characteristics are given in section 5.3.14 of the datasheet. |
| 8 | PC0 | bidirectional | General-purpose I/O PC0 that also serves as ADC1 input channel 10 (ADC1_IN10). |
| 9 | PC1 | bidirectional | General-purpose I/O PC1 that also serves as ADC1 input channel 11 (ADC1_IN11). |
| 10 | PC2 | bidirectional | General-purpose I/O PC2 that also serves as ADC1 input channel 12 (ADC1_IN12). |
| 11 | PC3 | bidirectional | General-purpose I/O PC3 that also serves as ADC1 input channel 13 (ADC1_IN13); this pin exists on LQFP64 only. |
| 12 | VSSA | power_in | Analog ground reference pin for the ADC, DAC and reset/clock analog circuitry. |
| 13 | VDDA | power_in | Analog supply pin; the ADC characteristics specify VDDA from 2.4 V to 3.6 V. |
| 14 | PA0-WKUP | bidirectional | GPIO PA0 that also provides the WKUP wakeup input, USART2_CTS, ADC1_IN0 and TIM2_CH1_ETR. |
| 15 | PA1 | bidirectional | GPIO PA1 that also provides USART2_RTS, ADC1_IN1 and TIM2_CH2. |
| 16 | PA2 | bidirectional | GPIO PA2 that also provides USART2_TX, ADC1_IN2, TIM2_CH3 and TIM15_CH1. |
| 17 | PA3 | bidirectional | GPIO PA3 that also provides USART2_RX, ADC1_IN3, TIM2_CH4 and TIM15_CH2. |
| 18 | VSS_4 | power_in | Digital ground pin. |
| 19 | VDD_4 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 20 | PA4 | bidirectional | GPIO PA4 that also provides SPI1_NSS, ADC1_IN4, USART2_CK and DAC1_OUT. |
| 21 | PA5 | bidirectional | GPIO PA5 that also provides SPI1_SCK, ADC1_IN5 and DAC2_OUT. |
| 22 | PA6 | bidirectional | GPIO PA6 that also provides SPI1_MISO, ADC1_IN6 and TIM3_CH1; TIM1_BKIN and TIM16_CH1 are remap options. |
| 23 | PA7 | bidirectional | GPIO PA7 that also provides SPI1_MOSI, ADC1_IN7 and TIM3_CH2; TIM1_CH1N and TIM17_CH1 are remap options. |
| 24 | PC4 | bidirectional | General-purpose I/O PC4 that also serves as ADC1 input channel 14 (ADC1_IN14). |
| 25 | PC5 | bidirectional | General-purpose I/O PC5 that also serves as ADC1 input channel 15 (ADC1_IN15). |
| 26 | PB0 | bidirectional | GPIO PB0 that also provides ADC1_IN8 and TIM3_CH3; TIM1_CH2N is a remap option. |
| 27 | PB1 | bidirectional | GPIO PB1 that also provides ADC1_IN9 and TIM3_CH4; TIM1_CH3N is a remap option. |
| 28 | PB2/BOOT1 | bidirectional | 5 V tolerant (FT) GPIO PB2 that is also the BOOT1 boot-mode pin. |
| 29 | PB10 | bidirectional | 5 V tolerant (FT) GPIO PB10 that also provides I2C2_SCL, USART3_TX, TIM2_CH3 and HDMI_CEC. |
| 30 | PB11 | bidirectional | 5 V tolerant (FT) GPIO PB11 that also provides I2C2_SDA, USART3_RX and TIM2_CH4. |
| 31 | VSS_1 | power_in | Digital ground pin. |
| 32 | VDD_1 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 33 | PB12 | bidirectional | 5 V tolerant (FT) GPIO PB12 that also provides SPI2_NSS, I2C2_SMBA, TIM1_BKIN and USART3_CK. |
| 34 | PB13 | bidirectional | 5 V tolerant (FT) GPIO PB13 that also provides SPI2_SCK, TIM1_CH1N and USART3_CTS. |
| 35 | PB14 | bidirectional | 5 V tolerant (FT) GPIO PB14 that also provides SPI2_MISO, TIM1_CH2N, USART3_RTS and TIM15_CH1. |
| 36 | PB15 | bidirectional | 5 V tolerant (FT) GPIO PB15 that also provides SPI2_MOSI, TIM1_CH3N, TIM15_CH1N and TIM15_CH2. |
| 37 | PC6 | bidirectional | 5 V tolerant (FT) GPIO PC6 that also provides TIM3_CH1. |
| 38 | PC7 | bidirectional | 5 V tolerant (FT) GPIO PC7 that also provides TIM3_CH2. |
| 39 | PC8 | bidirectional | 5 V tolerant (FT) GPIO PC8 that also provides TIM3_CH3. |
| 40 | PC9 | bidirectional | 5 V tolerant (FT) GPIO PC9 that also provides TIM3_CH4. |
| 41 | PA8 | bidirectional | 5 V tolerant (FT) GPIO PA8 that also provides USART1_CK, MCO and TIM1_CH1. |
| 42 | PA9 | bidirectional | 5 V tolerant (FT) GPIO PA9 that also provides USART1_TX, TIM1_CH2 and TIM15_BKIN. |
| 43 | PA10 | bidirectional | 5 V tolerant (FT) GPIO PA10 that also provides USART1_RX, TIM1_CH3 and TIM17_BKIN. |
| 44 | PA11 | bidirectional | 5 V tolerant (FT) GPIO PA11 that also provides USART1_CTS and TIM1_CH4. |
| 45 | PA12 | bidirectional | 5 V tolerant (FT) GPIO PA12 that also provides USART1_RTS and TIM1_ETR. |
| 46 | PA13 | bidirectional | 5 V tolerant (FT) GPIO PA13 that is the JTMS-SWDIO debug pin after reset. |
| 47 | VSS_2 | power_in | Digital ground pin. |
| 48 | VDD_2 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 49 | PA14 | bidirectional | 5 V tolerant (FT) GPIO PA14 that is the JTCK-SWCLK debug pin after reset. |
| 50 | PA15 | bidirectional | 5 V tolerant (FT) GPIO PA15 that is the JTDI debug pin after reset; TIM2_CH1_ETR and SPI1_NSS are remap options. |
| 51 | PC10 | bidirectional | 5 V tolerant (FT) GPIO PC10 with USART3_TX as a remap alternate function. |
| 52 | PC11 | bidirectional | 5 V tolerant (FT) GPIO PC11 with USART3_RX as a remap alternate function. |
| 53 | PC12 | bidirectional | 5 V tolerant (FT) GPIO PC12 with USART3_CK as a remap alternate function. |
| 54 | PD2 | bidirectional | 5 V tolerant (FT) GPIO PD2 that also provides TIM3_ETR. |
| 55 | PB3 | bidirectional | 5 V tolerant (FT) GPIO PB3 whose default function is JTDO; TRACESWO, TIM2_CH2 and SPI1_SCK are also available. |
| 56 | PB4 | bidirectional | 5 V tolerant (FT) GPIO PB4 whose default function is NJTRST; TIM3_CH1 and SPI1_MISO are remap options. |
| 57 | PB5 | bidirectional | GPIO PB5 that also provides I2C1_SMBA and TIM16_BKIN; TIM3_CH2 and SPI1_MOSI are remap options. |
| 58 | PB6 | bidirectional | 5 V tolerant (FT) GPIO PB6 that also provides I2C1_SCL, TIM4_CH1, TIM16_CH1N and USART1_TX. |
| 59 | PB7 | bidirectional | 5 V tolerant (FT) GPIO PB7 that also provides I2C1_SDA, TIM17_CH1N, TIM4_CH2 and USART1_RX. |
| 60 | BOOT0 | input | Boot mode selection input pin, listed as input type I in the pin definitions table. |
| 61 | PB8 | bidirectional | 5 V tolerant (FT) GPIO PB8 that also provides TIM4_CH3, TIM16_CH1, CEC and I2C1_SCL. |
| 62 | PB9 | bidirectional | 5 V tolerant (FT) GPIO PB9 that also provides TIM4_CH4, TIM17_CH1 and I2C1_SDA. |
| 63 | VSS_3 | power_in | Digital ground pin. |
| 64 | VDD_3 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD − VSS | -0.3 | 4 | V | 33 | ||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 33 | |||
| Variations between all the different ground pins | /VSSX − VSS/ | 50 | mV | 33 | |||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 34 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 34 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 34 | |||
| Output current sourced by any I/O and control pin | IIO | -25 | mA | 34 | |||
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | 0 | mA | 34 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 34 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 34 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 34 | ||
| Maximum junction temperature | TJ | 150 | °C | 34 | |||
| Internal AHB clock frequency | fHCLK | 0 | 24 | MHz | 34 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 24 | MHz | 34 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 24 | MHz | 34 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 34 | ||
| Analog operating voltage (ADC not used) | VDDA | 2 | 3.6 | V | ADC not used; must be the same potential as VDD | 34 | |
| Analog operating voltage (ADC used) | VDDA | 2.4 | 3.6 | V | ADC used | 34 | |
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 34 | ||
| Ambient temperature for 6 suffix version | TA | -40 | 85 | °C | 6 suffix version, maximum power dissipation | 35 | |
| Junction temperature range, 6 suffix version | TJ | -40 | 105 | °C | 6 suffix version | 35 | |
| Power dissipation, LQFP64 | PD | 444 | mW | TA = 85 °C for suffix 6 | 35 | ||
| VDD rise time rate | tVDD | 0 | µs/V | 35 | |||
| VDD fall time rate | tVDD | 20 | µs/V | 35 | |||
| Programmable voltage detector level, PLS[2:0]=000 rising edge | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=000 falling edge | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=111 rising edge | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=111 falling edge | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=111 (falling edge) | 36 |
| PVD hysteresis | VPVDhyst | 100 | mV | 36 | |||
| Power on/power down reset threshold, falling edge | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 36 |
| Power on/power down reset threshold, rising edge | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 36 |
| PDR hysteresis | VPDRhyst | 40 | mV | 36 | |||
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | 36 | |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.24 | V | −40 °C < TA < +85 °C | 37 |
| ADC sampling time when reading the internal reference voltage | TS_vrefint | 5.1 | 17.1 | µs | 37 | ||
| Internal reference voltage spread over the temperature range | VRERINT | 10 | mV | VDD = 3 V | 37 | ||
| Temperature coefficient | TCoeff | 100 | ppm/°C | 37 | |||
| Supply current in Run mode, code from Flash, external clock, all peripherals enabled, 24 MHz | IDD | 15.4 | mA | TA = 85 °C | 38 | ||
| Supply current in Run mode, code from Flash, external clock, all peripherals disabled, 24 MHz | IDD | 10.3 | mA | TA = 85 °C | 38 | ||
| Supply current in Run mode, code from Flash, external clock, all peripherals enabled, 8 MHz | IDD | 6.7 | mA | TA = 85 °C | 38 | ||
| Supply current in Run mode, code from Flash, external clock, all peripherals disabled, 8 MHz | IDD | 5.1 | mA | TA = 85 °C | 38 | ||
| Supply current in Run mode, code from RAM, external clock, all peripherals enabled, 24 MHz | IDD | 14.5 | mA | TA = 85 °C | 38 | ||
| Supply current in Run mode, code from RAM, external clock, all peripherals disabled, 24 MHz | IDD | 9.3 | mA | TA = 85 °C | 38 | ||
| Supply current in Stop mode, regulator in Run mode | IDD | 190 | µA | Regulator in Run mode; LSI, HSI and HSE OFF; TA = 85 °C | 40 | ||
| Supply current in Stop mode, regulator in Low-power mode | IDD | 170 | µA | Regulator in Low-power mode; LSI, HSI and HSE OFF; TA = 85 °C | 40 | ||
| Supply current in Standby mode, LSI and independent watchdog OFF, LSE and RTC OFF | IDD | 4 | µA | TA = 85 °C | 40 | ||
| Backup domain supply current, LSE and RTC ON | IDD_VBAT | 1.9 | µA | TA = 85 °C | 40 | ||
| User external clock source frequency (HSE) | fHSE_ext | 1 | 8 | 24 | MHz | 46 | |
| HSE duty cycle | DuCy(HSE) | 45 | 55 | % | 46 | ||
| Oscillator frequency (HSE crystal/resonator) | fOSC_IN | 4 | 8 | 24 | MHz | 48 | |
| Feedback resistor (HSE) | RF | 200 | kΩ | 48 | |||
| Oscillator transconductance | gm | 25 | mA/V | Startup | 48 | ||
| NRST Input low level voltage | VIL(NRST) | -0.5 | 0.8 | V | 62 | ||
| NRST Input high level voltage | VIH(NRST) | 2 | V | 62 | |||
| NRST Schmitt trigger voltage hysteresis | Vhys(NRST) | 200 | mV | 62 | |||
| NRST Weak pull-up equivalent resistor | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 62 |
| NRST Input not filtered pulse | VNF(NRST) | 300 | ns | 62 | |||
| Weak pull-up equivalent resistor (I/O) | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 57 |
| Weak pull-down equivalent resistor (I/O) | RPD | 30 | 40 | 50 | kΩ | VIN = VDD | 57 |
| I/O pin capacitance | CIO | 5 | pF | 57 |
CAD (KiCad official)
- Symbol:
STM32F100RBT6BTR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
stm32f100rbt6btr-etched.step/stm32f100rbt6btr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f100rbt6btr.step/stm32f100rbt6btr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (96 pp, sha256
360e3be010cabad4, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# STM32F100RBT6BTR
**STMicroelectronics** · ST Microelectronics · LQFP-64(10x10)
STM32F100RBT6BTR from STMicroelectronics, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup-domain supply input for the RTC and backup registers, as stated in the VBAT supply feature. |
| 2 | PC13-TAMPER-RTC | bidirectional | GPIO PC13 (also TAMPER-RTC); it is supplied through the power switch, which sinks only 3 mA, so output speed must not exceed 2 MHz at 30 pF and it must not source current such as LED drive. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO PC14 (also OSC32_IN for the 32.768 kHz oscillator); it is supplied through the power switch with the same 3 mA sink limit and 2 MHz / 30 pF output restriction. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO PC15 (also OSC32_OUT for the 32.768 kHz oscillator); it is supplied through the power switch with the same 3 mA sink limit and 2 MHz / 30 pF output restriction. |
| 5 | OSC_IN | input | HSE 4-24 MHz crystal oscillator input, configured as OSC_IN after reset; PD0 can be remapped onto this pin by software. |
| 6 | OSC_OUT | output | HSE 4-24 MHz crystal oscillator output, configured as OSC_OUT after reset; PD1 can be remapped onto this pin by software. |
| 7 | NRST | bidirectional | Device reset pin (active low); its electrical characteristics are given in section 5.3.14 of the datasheet. |
| 8 | PC0 | bidirectional | General-purpose I/O PC0 that also serves as ADC1 input channel 10 (ADC1_IN10). |
| 9 | PC1 | bidirectional | General-purpose I/O PC1 that also serves as ADC1 input channel 11 (ADC1_IN11). |
| 10 | PC2 | bidirectional | General-purpose I/O PC2 that also serves as ADC1 input channel 12 (ADC1_IN12). |
| 11 | PC3 | bidirectional | General-purpose I/O PC3 that also serves as ADC1 input channel 13 (ADC1_IN13); this pin exists on LQFP64 only. |
| 12 | VSSA | power_in | Analog ground reference pin for the ADC, DAC and reset/clock analog circuitry. |
| 13 | VDDA | power_in | Analog supply pin; the ADC characteristics specify VDDA from 2.4 V to 3.6 V. |
| 14 | PA0-WKUP | bidirectional | GPIO PA0 that also provides the WKUP wakeup input, USART2_CTS, ADC1_IN0 and TIM2_CH1_ETR. |
| 15 | PA1 | bidirectional | GPIO PA1 that also provides USART2_RTS, ADC1_IN1 and TIM2_CH2. |
| 16 | PA2 | bidirectional | GPIO PA2 that also provides USART2_TX, ADC1_IN2, TIM2_CH3 and TIM15_CH1. |
| 17 | PA3 | bidirectional | GPIO PA3 that also provides USART2_RX, ADC1_IN3, TIM2_CH4 and TIM15_CH2. |
| 18 | VSS_4 | power_in | Digital ground pin. |
| 19 | VDD_4 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 20 | PA4 | bidirectional | GPIO PA4 that also provides SPI1_NSS, ADC1_IN4, USART2_CK and DAC1_OUT. |
| 21 | PA5 | bidirectional | GPIO PA5 that also provides SPI1_SCK, ADC1_IN5 and DAC2_OUT. |
| 22 | PA6 | bidirectional | GPIO PA6 that also provides SPI1_MISO, ADC1_IN6 and TIM3_CH1; TIM1_BKIN and TIM16_CH1 are remap options. |
| 23 | PA7 | bidirectional | GPIO PA7 that also provides SPI1_MOSI, ADC1_IN7 and TIM3_CH2; TIM1_CH1N and TIM17_CH1 are remap options. |
| 24 | PC4 | bidirectional | General-purpose I/O PC4 that also serves as ADC1 input channel 14 (ADC1_IN14). |
| 25 | PC5 | bidirectional | General-purpose I/O PC5 that also serves as ADC1 input channel 15 (ADC1_IN15). |
| 26 | PB0 | bidirectional | GPIO PB0 that also provides ADC1_IN8 and TIM3_CH3; TIM1_CH2N is a remap option. |
| 27 | PB1 | bidirectional | GPIO PB1 that also provides ADC1_IN9 and TIM3_CH4; TIM1_CH3N is a remap option. |
| 28 | PB2/BOOT1 | bidirectional | 5 V tolerant (FT) GPIO PB2 that is also the BOOT1 boot-mode pin. |
| 29 | PB10 | bidirectional | 5 V tolerant (FT) GPIO PB10 that also provides I2C2_SCL, USART3_TX, TIM2_CH3 and HDMI_CEC. |
| 30 | PB11 | bidirectional | 5 V tolerant (FT) GPIO PB11 that also provides I2C2_SDA, USART3_RX and TIM2_CH4. |
| 31 | VSS_1 | power_in | Digital ground pin. |
| 32 | VDD_1 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 33 | PB12 | bidirectional | 5 V tolerant (FT) GPIO PB12 that also provides SPI2_NSS, I2C2_SMBA, TIM1_BKIN and USART3_CK. |
| 34 | PB13 | bidirectional | 5 V tolerant (FT) GPIO PB13 that also provides SPI2_SCK, TIM1_CH1N and USART3_CTS. |
| 35 | PB14 | bidirectional | 5 V tolerant (FT) GPIO PB14 that also provides SPI2_MISO, TIM1_CH2N, USART3_RTS and TIM15_CH1. |
| 36 | PB15 | bidirectional | 5 V tolerant (FT) GPIO PB15 that also provides SPI2_MOSI, TIM1_CH3N, TIM15_CH1N and TIM15_CH2. |
| 37 | PC6 | bidirectional | 5 V tolerant (FT) GPIO PC6 that also provides TIM3_CH1. |
| 38 | PC7 | bidirectional | 5 V tolerant (FT) GPIO PC7 that also provides TIM3_CH2. |
| 39 | PC8 | bidirectional | 5 V tolerant (FT) GPIO PC8 that also provides TIM3_CH3. |
| 40 | PC9 | bidirectional | 5 V tolerant (FT) GPIO PC9 that also provides TIM3_CH4. |
| 41 | PA8 | bidirectional | 5 V tolerant (FT) GPIO PA8 that also provides USART1_CK, MCO and TIM1_CH1. |
| 42 | PA9 | bidirectional | 5 V tolerant (FT) GPIO PA9 that also provides USART1_TX, TIM1_CH2 and TIM15_BKIN. |
| 43 | PA10 | bidirectional | 5 V tolerant (FT) GPIO PA10 that also provides USART1_RX, TIM1_CH3 and TIM17_BKIN. |
| 44 | PA11 | bidirectional | 5 V tolerant (FT) GPIO PA11 that also provides USART1_CTS and TIM1_CH4. |
| 45 | PA12 | bidirectional | 5 V tolerant (FT) GPIO PA12 that also provides USART1_RTS and TIM1_ETR. |
| 46 | PA13 | bidirectional | 5 V tolerant (FT) GPIO PA13 that is the JTMS-SWDIO debug pin after reset. |
| 47 | VSS_2 | power_in | Digital ground pin. |
| 48 | VDD_2 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
| 49 | PA14 | bidirectional | 5 V tolerant (FT) GPIO PA14 that is the JTCK-SWCLK debug pin after reset. |
| 50 | PA15 | bidirectional | 5 V tolerant (FT) GPIO PA15 that is the JTDI debug pin after reset; TIM2_CH1_ETR and SPI1_NSS are remap options. |
| 51 | PC10 | bidirectional | 5 V tolerant (FT) GPIO PC10 with USART3_TX as a remap alternate function. |
| 52 | PC11 | bidirectional | 5 V tolerant (FT) GPIO PC11 with USART3_RX as a remap alternate function. |
| 53 | PC12 | bidirectional | 5 V tolerant (FT) GPIO PC12 with USART3_CK as a remap alternate function. |
| 54 | PD2 | bidirectional | 5 V tolerant (FT) GPIO PD2 that also provides TIM3_ETR. |
| 55 | PB3 | bidirectional | 5 V tolerant (FT) GPIO PB3 whose default function is JTDO; TRACESWO, TIM2_CH2 and SPI1_SCK are also available. |
| 56 | PB4 | bidirectional | 5 V tolerant (FT) GPIO PB4 whose default function is NJTRST; TIM3_CH1 and SPI1_MISO are remap options. |
| 57 | PB5 | bidirectional | GPIO PB5 that also provides I2C1_SMBA and TIM16_BKIN; TIM3_CH2 and SPI1_MOSI are remap options. |
| 58 | PB6 | bidirectional | 5 V tolerant (FT) GPIO PB6 that also provides I2C1_SCL, TIM4_CH1, TIM16_CH1N and USART1_TX. |
| 59 | PB7 | bidirectional | 5 V tolerant (FT) GPIO PB7 that also provides I2C1_SDA, TIM17_CH1N, TIM4_CH2 and USART1_RX. |
| 60 | BOOT0 | input | Boot mode selection input pin, listed as input type I in the pin definitions table. |
| 61 | PB8 | bidirectional | 5 V tolerant (FT) GPIO PB8 that also provides TIM4_CH3, TIM16_CH1, CEC and I2C1_SCL. |
| 62 | PB9 | bidirectional | 5 V tolerant (FT) GPIO PB9 that also provides TIM4_CH4, TIM17_CH1 and I2C1_SDA. |
| 63 | VSS_3 | power_in | Digital ground pin. |
| 64 | VDD_3 | power_in | Digital supply pin for the 2.0 to 3.6 V application supply and I/Os. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD − VSS | -0.3 | | 4 | V | | 33 |
| Variations between different VDD power pins | /ΔVDDx/ | | | 50 | mV | | 33 |
| Variations between all the different ground pins | /VSSX − VSS/ | | | 50 | mV | | 33 |
| Total current into VDD/VDDA power lines (source) | IVDD | | | 150 | mA | | 34 |
| Total current out of VSS ground lines (sink) | IVSS | | | 150 | mA | | 34 |
| Output current sunk by any I/O and control pin | IIO | | | 25 | mA | | 34 |
| Output current sourced by any I/O and control pin | IIO | | | -25 | mA | | 34 |
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | | 0 | mA | | 34 |
| Injected current on any other pin | IINJ(PIN) | -5 | | 5 | mA | | 34 |
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | | 25 | mA | | 34 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 34 |
| Maximum junction temperature | TJ | | | 150 | °C | | 34 |
| Internal AHB clock frequency | fHCLK | 0 | | 24 | MHz | | 34 |
| Internal APB1 clock frequency | fPCLK1 | 0 | | 24 | MHz | | 34 |
| Internal APB2 clock frequency | fPCLK2 | 0 | | 24 | MHz | | 34 |
| Standard operating voltage | VDD | 2 | | 3.6 | V | | 34 |
| Analog operating voltage (ADC not used) | VDDA | 2 | | 3.6 | V | ADC not used; must be the same potential as VDD | 34 |
| Analog operating voltage (ADC used) | VDDA | 2.4 | | 3.6 | V | ADC used | 34 |
| Backup operating voltage | VBAT | 1.8 | | 3.6 | V | | 34 |
| Ambient temperature for 6 suffix version | TA | -40 | | 85 | °C | 6 suffix version, maximum power dissipation | 35 |
| Junction temperature range, 6 suffix version | TJ | -40 | | 105 | °C | 6 suffix version | 35 |
| Power dissipation, LQFP64 | PD | | | 444 | mW | TA = 85 °C for suffix 6 | 35 |
| VDD rise time rate | tVDD | 0 | | | µs/V | | 35 |
| VDD fall time rate | tVDD | 20 | | | µs/V | | 35 |
| Programmable voltage detector level, PLS[2:0]=000 rising edge | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=000 falling edge | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=111 rising edge | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 36 |
| Programmable voltage detector level, PLS[2:0]=111 falling edge | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=111 (falling edge) | 36 |
| PVD hysteresis | VPVDhyst | | 100 | | mV | | 36 |
| Power on/power down reset threshold, falling edge | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 36 |
| Power on/power down reset threshold, rising edge | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 36 |
| PDR hysteresis | VPDRhyst | | 40 | | mV | | 36 |
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | | 36 |
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.24 | V | −40 °C < TA < +85 °C | 37 |
| ADC sampling time when reading the internal reference voltage | TS_vrefint | | 5.1 | 17.1 | µs | | 37 |
| Internal reference voltage spread over the temperature range | VRERINT | | | 10 | mV | VDD = 3 V | 37 |
| Temperature coefficient | TCoeff | | | 100 | ppm/°C | | 37 |
| Supply current in Run mode, code from Flash, external clock, all peripherals enabled, 24 MHz | IDD | | | 15.4 | mA | TA = 85 °C | 38 |
| Supply current in Run mode, code from Flash, external clock, all peripherals disabled, 24 MHz | IDD | | | 10.3 | mA | TA = 85 °C | 38 |
| Supply current in Run mode, code from Flash, external clock, all peripherals enabled, 8 MHz | IDD | | | 6.7 | mA | TA = 85 °C | 38 |
| Supply current in Run mode, code from Flash, external clock, all peripherals disabled, 8 MHz | IDD | | | 5.1 | mA | TA = 85 °C | 38 |
| Supply current in Run mode, code from RAM, external clock, all peripherals enabled, 24 MHz | IDD | | | 14.5 | mA | TA = 85 °C | 38 |
| Supply current in Run mode, code from RAM, external clock, all peripherals disabled, 24 MHz | IDD | | | 9.3 | mA | TA = 85 °C | 38 |
| Supply current in Stop mode, regulator in Run mode | IDD | | | 190 | µA | Regulator in Run mode; LSI, HSI and HSE OFF; TA = 85 °C | 40 |
| Supply current in Stop mode, regulator in Low-power mode | IDD | | | 170 | µA | Regulator in Low-power mode; LSI, HSI and HSE OFF; TA = 85 °C | 40 |
| Supply current in Standby mode, LSI and independent watchdog OFF, LSE and RTC OFF | IDD | | | 4 | µA | TA = 85 °C | 40 |
| Backup domain supply current, LSE and RTC ON | IDD_VBAT | | | 1.9 | µA | TA = 85 °C | 40 |
| User external clock source frequency (HSE) | fHSE_ext | 1 | 8 | 24 | MHz | | 46 |
| HSE duty cycle | DuCy(HSE) | 45 | | 55 | % | | 46 |
| Oscillator frequency (HSE crystal/resonator) | fOSC_IN | 4 | 8 | 24 | MHz | | 48 |
| Feedback resistor (HSE) | RF | | 200 | | kΩ | | 48 |
| Oscillator transconductance | gm | 25 | | | mA/V | Startup | 48 |
| NRST Input low level voltage | VIL(NRST) | -0.5 | | 0.8 | V | | 62 |
| NRST Input high level voltage | VIH(NRST) | 2 | | | V | | 62 |
| NRST Schmitt trigger voltage hysteresis | Vhys(NRST) | | 200 | | mV | | 62 |
| NRST Weak pull-up equivalent resistor | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 62 |
| NRST Input not filtered pulse | VNF(NRST) | 300 | | | ns | | 62 |
| Weak pull-up equivalent resistor (I/O) | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 57 |
| Weak pull-down equivalent resistor (I/O) | RPD | 30 | 40 | 50 | kΩ | VIN = VDD | 57 |
| I/O pin capacitance | CIO | | 5 | | pF | | 57 |
## CAD (KiCad official)
- Symbol: `STM32F100RBT6BTR`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `stm32f100rbt6btr-etched.step` / `stm32f100rbt6btr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32f100rbt6btr.step` / `stm32f100rbt6btr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/content/ccc/resource/technical/document/datasheet/dd/87/fd/2a/fb/3f/48/5c/CD00251732.pdf/files/CD00251732.pdf/jcr:content/translations/en.CD00251732.pdf) (96 pp, sha256 `360e3be010cabad4`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/stm32f100rbt6btr-datasheet.pdf)