component
STM32F100CBT7BTR
Public Made by Adomby adom
STMicroelectronics ST Microelectronics, LQFP-48(7x7). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSTM32F100CBT7BTR
STMicroelectronics · ST Microelectronics · LQFP-48(7x7)
STM32F100CBT7BTR from STMicroelectronics, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBAT | power_in | Backup power supply for the RTC and backup registers. |
| 2 | PC13-TAMPER-RTC | bidirectional | GPIO PC13 (also TAMPER-RTC) is supplied through the power switch, which sinks only 3 mA, so output use is limited to 2 MHz with a 30 pF maximum load and the pin must not source current such as driving an LED. |
| 3 | PC14-OSC32_IN | bidirectional | GPIO PC14 (also 32 kHz oscillator input OSC32_IN) is supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and the pin must not source current. |
| 4 | PC15-OSC32_OUT | bidirectional | GPIO PC15 (also 32 kHz oscillator output OSC32_OUT) is supplied through the power switch, so output use is limited to 2 MHz with a 30 pF maximum load and the pin must not source current. |
| 5 | OSC_IN | input | External high-speed oscillator input (4-24 MHz crystal), configured as OSC_IN after reset, with PD0 remappable onto this pin by software. |
| 6 | OSC_OUT | output | External high-speed oscillator output (4-24 MHz crystal), configured as OSC_OUT after reset, with PD1 remappable onto this pin by software. |
| 7 | NRST | bidirectional | Device reset pin, listed as I/O in Table 4; its electrical characteristics are given in section 5.3.14. |
| 8 | VSSA | power_in | Analog ground; the ADC conversion range of 0 to VREF+ assumes VSSA is tied to ground. |
| 9 | VDDA | power_in | Analog supply for the ADC, DAC and temperature sensor, with a VDDA range of 2.4 V to 3.6 V for the ADC. |
| 10 | PA0-WKUP | bidirectional | GPIO PA0 (not 5 V tolerant) with alternate functions WKUP, USART2_CTS, ADC1_IN0 and TIM2_CH1_ETR. |
| 11 | PA1 | bidirectional | GPIO PA1 (not 5 V tolerant) with alternate functions USART2_RTS, ADC1_IN1 and TIM2_CH2. |
| 12 | PA2 | bidirectional | GPIO PA2 (not 5 V tolerant) with alternate functions USART2_TX, ADC1_IN2, TIM2_CH3 and TIM15_CH1. |
| 13 | PA3 | bidirectional | GPIO PA3 (not 5 V tolerant) with alternate functions USART2_RX, ADC1_IN3, TIM2_CH4 and TIM15_CH2. |
| 14 | PA4 | bidirectional | GPIO PA4 (not 5 V tolerant) with alternate functions SPI1_NSS, ADC1_IN4, USART2_CK and DAC1_OUT. |
| 15 | PA5 | bidirectional | GPIO PA5 (not 5 V tolerant) with alternate functions SPI1_SCK, ADC1_IN5 and DAC2_OUT. |
| 16 | PA6 | bidirectional | GPIO PA6 (not 5 V tolerant) with alternate functions SPI1_MISO, ADC1_IN6, TIM3_CH1, and remap TIM1_BKIN and TIM16_CH1. |
| 17 | PA7 | bidirectional | GPIO PA7 (not 5 V tolerant) with alternate functions SPI1_MOSI, ADC1_IN7 and TIM3_CH2, and remap TIM1_CH1N and TIM17_CH1. |
| 18 | PB0 | bidirectional | GPIO PB0 (not 5 V tolerant) with alternate functions ADC1_IN8 and TIM3_CH3, and remap TIM1_CH2N. |
| 19 | PB1 | bidirectional | GPIO PB1 (not 5 V tolerant) with alternate functions ADC1_IN9 and TIM3_CH4, and remap TIM1_CH3N. |
| 20 | PB2/BOOT1 | bidirectional | 5 V tolerant GPIO PB2, also used as the BOOT1 boot-mode input. |
| 21 | PB10 | bidirectional | 5 V tolerant GPIO PB10 with alternate functions I2C2_SCL, USART3_TX, TIM2_CH3 and HDMI_CEC. |
| 22 | PB11 | bidirectional | 5 V tolerant GPIO PB11 with alternate functions I2C2_SDA, USART3_RX and TIM2_CH4. |
| 23 | VSS_1 | power_in | Ground pin for the digital supply domain. |
| 24 | VDD_1 | power_in | Digital supply pin; application supply and I/Os are specified from 2.0 V to 3.6 V. |
| 25 | PB12 | bidirectional | 5 V tolerant GPIO PB12 with alternate functions SPI2_NSS, I2C2_SMBA, TIM1_BKIN and USART3_CK. |
| 26 | PB13 | bidirectional | 5 V tolerant GPIO PB13 with alternate functions SPI2_SCK, TIM1_CH1N and USART3_CTS. |
| 27 | PB14 | bidirectional | 5 V tolerant GPIO PB14 with alternate functions SPI2_MISO, TIM1_CH2N, USART3_RTS and TIM15_CH1. |
| 28 | PB15 | bidirectional | 5 V tolerant GPIO PB15 with alternate functions SPI2_MOSI, TIM1_CH3N, TIM15_CH1N and remap TIM15_CH2. |
| 29 | PA8 | bidirectional | 5 V tolerant GPIO PA8 with alternate functions USART1_CK, MCO and TIM1_CH1. |
| 30 | PA9 | bidirectional | 5 V tolerant GPIO PA9 with alternate functions USART1_TX, TIM1_CH2 and TIM15_BKIN (remap). |
| 31 | PA10 | bidirectional | 5 V tolerant GPIO PA10 with alternate functions USART1_RX, TIM1_CH3 and TIM17_BKIN (remap). |
| 32 | PA11 | bidirectional | 5 V tolerant GPIO PA11 with alternate functions USART1_CTS and TIM1_CH4. |
| 33 | PA12 | bidirectional | 5 V tolerant GPIO PA12 with alternate functions USART1_RTS and TIM1_ETR. |
| 34 | PA13 | bidirectional | 5 V tolerant GPIO PA13, default function JTMS-SWDIO (serial wire debug data input/output). |
| 35 | VSS_2 | power_in | Ground pin for the digital supply domain. |
| 36 | VDD_2 | power_in | Digital supply pin; application supply and I/Os are specified from 2.0 V to 3.6 V. |
| 37 | PA14 | bidirectional | 5 V tolerant GPIO PA14, default function JTCK/SWCLK (serial wire debug clock). |
| 38 | PA15 | bidirectional | 5 V tolerant GPIO PA15, default function JTDI, with remap alternate functions TIM2_CH1_ETR and SPI1_NSS. |
| 39 | PB3 | bidirectional | 5 V tolerant GPIO PB3, default function JTDO, with alternate functions TRACESWO, TIM2_CH2 and SPI1_SCK (remap). |
| 40 | PB4 | bidirectional | 5 V tolerant GPIO PB4, default function NJTRST, with alternate functions TIM3_CH1 and SPI1_MISO (remap). |
| 41 | PB5 | bidirectional | GPIO PB5 (not 5 V tolerant) with alternate functions I2C1_SMBA, TIM16_BKIN, and remap TIM3_CH2 and SPI1_MOSI. |
| 42 | PB6 | bidirectional | 5 V tolerant GPIO PB6 with alternate functions I2C1_SCL, TIM4_CH1, TIM16_CH1N and USART1_TX (remap). |
| 43 | PB7 | bidirectional | 5 V tolerant GPIO PB7 with alternate functions I2C1_SDA, TIM4_CH2, TIM17_CH1N and USART1_RX (remap). |
| 44 | BOOT0 | input | Boot-mode selection input BOOT0. |
| 45 | PB8 | bidirectional | 5 V tolerant GPIO PB8 with alternate functions TIM4_CH3, TIM16_CH1, CEC and I2C1_SCL. |
| 46 | PB9 | bidirectional | 5 V tolerant GPIO PB9 with alternate functions TIM4_CH4, TIM17_CH1 and I2C1_SDA. |
| 47 | VSS_3 | power_in | Ground pin for the digital supply domain. |
| 48 | VDD_3 | power_in | Digital supply pin; application supply and I/Os are specified from 2.0 V to 3.6 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | LQFP-48(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 48 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| External main supply voltage (including VDDA and VDD) | VDD − VSS | -0.3 | 4 | V | 33 | ||
| Input voltage on any other pin | VIN | 4 | V | 33 | |||
| Variations between different VDD power pins | /ΔVDDx/ | 50 | mV | 33 | |||
| Variations between all the different ground pins | /VSSX −VSS/ | 50 | mV | 33 | |||
| Total current into VDD/VDDA power lines (source) | IVDD | 150 | mA | 34 | |||
| Total current out of VSS ground lines (sink) | IVSS | 150 | mA | 34 | |||
| Output current sunk by any I/O and control pin | IIO | 25 | mA | 34 | |||
| Output current source by any I/Os and control pin | IIO | -25 | mA | 34 | |||
| Injected current on five volt tolerant pins | IINJ(PIN) | -5 | 0 | mA | 34 | ||
| Injected current on any other pin | IINJ(PIN) | -5 | 5 | mA | 34 | ||
| Total injected current (sum of all I/O and control pins) | ΣIINJ(PIN) | -25 | 25 | mA | 34 | ||
| Storage temperature range | TSTG | -65 | 150 | °C | 34 | ||
| Maximum junction temperature | TJ | 150 | °C | 34 | |||
| Internal AHB clock frequency | fHCLK | 0 | 24 | MHz | 34 | ||
| Internal APB1 clock frequency | fPCLK1 | 0 | 24 | MHz | 34 | ||
| Internal APB2 clock frequency | fPCLK2 | 0 | 24 | MHz | 34 | ||
| Standard operating voltage | VDD | 2 | 3.6 | V | 34 | ||
| Analog operating voltage (ADC not used) | VDDA | 2 | 3.6 | V | Must be the same potential as VDD | 34 | |
| Analog operating voltage (ADC used) | VDDA | 2.4 | 3.6 | V | ADC used | 34 | |
| Backup operating voltage | VBAT | 1.8 | 3.6 | V | 34 | ||
| Power dissipation LQFP48 | PD | 363 | mW | TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 | 35 | ||
| Ambient temperature for 7 suffix version, maximum power dissipation | TA | -40 | 105 | °C | Maximum power dissipation | 35 | |
| Ambient temperature for 7 suffix version, low power dissipation | TA | -40 | 125 | °C | Low power dissipation | 35 | |
| Junction temperature range, 7 suffix version | TJ | -40 | 125 | °C | 7 suffix version | 35 | |
| Power-on/power-down reset threshold (falling edge) | VPOR/PDR | 1.8 | 1.88 | 1.96 | V | Falling edge | 36 |
| Power-on/power-down reset threshold (rising edge) | VPOR/PDR | 1.84 | 1.92 | 2 | V | Rising edge | 36 |
| PDR hysteresis | VPDRhyst | 40 | mV | 36 | |||
| Reset temporization | tRSTTEMPO | 1.5 | 2.5 | 4.5 | ms | 36 | |
| Programmable voltage detector level selection | VPVD | 2.1 | 2.18 | 2.26 | V | PLS[2:0]=000 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2 | 2.08 | 2.16 | V | PLS[2:0]=000 (falling edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.19 | 2.28 | 2.37 | V | PLS[2:0]=001 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.09 | 2.18 | 2.27 | V | PLS[2:0]=001 (falling edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.28 | 2.38 | 2.48 | V | PLS[2:0]=010 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.18 | 2.28 | 2.38 | V | PLS[2:0]=010 (falling edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.38 | 2.48 | 2.58 | V | PLS[2:0]=011 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.47 | 2.58 | 2.69 | V | PLS[2:0]=100 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.37 | 2.48 | 2.59 | V | PLS[2:0]=100 (falling edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.57 | 2.68 | 2.79 | V | PLS[2:0]=101 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.66 | 2.78 | 2.9 | V | PLS[2:0]=110 (rising edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.56 | 2.68 | 2.8 | V | PLS[2:0]=110 (falling edge) | 36 |
| Programmable voltage detector level selection | VPVD | 2.76 | 2.88 | 3 | V | PLS[2:0]=111 (rising edge) | 36 |
| PVD hysteresis | VPVDhyst | 100 | mV | 36 | |||
| Internal reference voltage | VREFINT | 1.16 | 1.2 | 1.26 | V | -40 °C < TA < +105 °C | 37 |
| Internal reference voltage spread over the temperature range | VRERINT | 10 | mV | VDD = 3 V | 37 | ||
| Temperature coefficient | TCoeff | 100 | ppm/°C | 37 | |||
| Supply current in Run mode, external clock, all peripherals enabled, from Flash | IDD | 15.7 | mA | fHCLK = 24 MHz, TA = 105 °C | 38 | ||
| Supply current in Stop mode | IDD | 350 | µA | Regulator in Run mode, low-speed and high-speed internal RC and high-speed oscillator OFF (no independent watchdog), TA = 105 °C | 40 | ||
| Supply current in Standby mode | IDD | 5 | µA | Low-speed internal RC and independent watchdog OFF, low-speed oscillator and RTC OFF, TA = 105 °C | 40 | ||
| Backup domain supply current | IDD_VBAT | 2.2 | µA | Low-speed oscillator and RTC ON, TA = 105 °C | 40 | ||
| 16-bit programming time | tprog | 40 | 52.5 | 70 | µs | TA = -40 to +105 °C | 53 |
| Page (1 KB) erase time | tERASE | 20 | 40 | ms | TA = -40 to +105 °C | 53 | |
| Programming voltage | Vprog | 2 | 3.6 | V | 53 | ||
| Endurance | NEND | 10 | kcycles | TA = -40 to +105 °C (7 suffix versions) | 53 | ||
| Standard I/O Schmitt trigger voltage hysteresis | Vhys | 200 | mV | 57 | |||
| Input leakage current, standard I/Os | Ilkg | -1 | 1 | µA | VSS ≤ VIN ≤ VDD | 57 | |
| Weak pull-up equivalent resistor | RPU | 30 | 40 | 50 | kΩ | VIN = VSS | 57 |
| Weak pull-down equivalent resistor | RPD | 30 | 40 | 50 | kΩ | VIN = VDD | 57 |
CAD (KiCad official)
- Symbol:
STM32F100CBT7BTR - Footprint:
Package_QFP:LQFP-48_7x7mm_P0.5mm - 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)
- 3D model files:
stm32f100cbt7btr-etched.step/stm32f100cbt7btr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stm32f100cbt7btr.step/stm32f100cbt7btr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (96 pp, sha256
360e3be010cabad4, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).