3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownSTC8H1K08T-33I-SOP16
STC Micro · Microcontroller Units (MCUs/MPUs/SOCs) · SOP-16
STC8H1K08T-33I-SOP16 from STC Micro, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P1.0 | bidirectional | Standard I/O port P1.0 (quasi-bidirectional, push-pull, open-drain or high-impedance input mode, optional 4K pull-up), multiplexed as ADC0 analog input, RxD2 (UART2 receive) and PWM1P; it powers up in high-impedance input and must be configured before use. |
| 2 | P1.1 | bidirectional | Standard I/O port P1.1 (quasi-bidirectional, push-pull, open-drain or high-impedance input mode, optional 4K pull-up), multiplexed as ADC1 analog input, TxD2 (UART2 transmit) and PWM1N output; it powers up in high-impedance input and must be configured before use. |
| 3 | P1.6 | bidirectional | Standard I/O port P1.6 (quasi-bidirectional, push-pull, open-drain or high-impedance input mode), multiplexed as UART1 receive RxD_3, PWM4P, master clock output MCLKO_2 and external crystal output XTALO; it powers up in high-impedance input and must be configured before use. |
| 4 | P1.7 | bidirectional | Standard I/O port P1.7 (quasi-bidirectional, push-pull, open-drain or high-impedance input mode), multiplexed as UART1 transmit TxD_3, PWM4N, PWM5_2 and external crystal/clock input XTALI; it powers up in high-impedance input and must be configured before use. |
| 5 | P5.4 | bidirectional | Standard I/O port P5.4 that is also the active-low reset input nRST (set as reset pin through ISP; factory default is I/O), multiplexed with MCLKO master clock output and PWM6_2; the internal 4K pull-up stays on when used as reset pin. |
| 6 | Vcc | power_in | Power supply pin for the MCU (also AVcc for the ADC); the working voltage range stated for this series is 1.9V to 5.5V. |
| 7 | ADC_VRef+ | input | ADC external reference voltage input, which must be connected to an external reference between 2.4V and MCU-VCC because a floating pin causes leakage current. |
| 8 | Gnd | power_in | Ground pin for the MCU, shared with the ADC analog ground AGnd. |
| 9 | P3.0 | bidirectional | Standard I/O port P3.0 (quasi-bidirectional/weak pull-up after power-up), multiplexed as ADC8 analog input, UART1 receive RxD and external interrupt INT4; it is also the ISP download/emulation data pin and must not be held low together with P3.1 and P3.2 at power-on unless software USB download is intended. |
| 10 | P3.1 | bidirectional | Standard I/O port P3.1 (quasi-bidirectional/weak pull-up after power-up), multiplexed as ADC9 analog input and UART1 transmit TxD; it is also used for ISP download/emulation together with P3.0. |
| 11 | P3.2 | bidirectional | Standard I/O port P3.2, multiplexed as ADC10 analog input, external interrupt INT0, SPI clock SCLK_4, I2C clock SCL_4 and PWM external trigger inputs PWMETI/PWMETI2; it is sampled at power-on together with P3.0/P3.1 to decide on software USB download mode. |
| 12 | P3.3 | bidirectional | Standard I/O port P3.3, multiplexed as ADC11 analog input, external interrupt INT1, SPI MISO_4, I2C data SDA_4, PWM4N_4 and PWM7_2 output/capture. |
| 13 | P3.4 | bidirectional | Standard I/O port P3.4, multiplexed as ADC12 analog input, Timer 0 external clock input T0, T1CLKO clock output, SPI MOSI_4, PWM4P_4, PWM8_2 and comparator output CMPO. |
| 14 | P3.5 | bidirectional | Standard I/O port P3.5, multiplexed as ADC13 analog input, Timer 1 external clock input T1, T0CLKO clock output, SPI slave select SS_4, and PWMA/PWMB fault detection inputs PWMFLT/PWMFLT2. |
| 15 | P3.6 | bidirectional | Standard I/O port P3.6, multiplexed as ADC14 analog input, external interrupt INT2 (falling edge only), UART1 receive RxD_2 and comparator negative input CMP-. |
| 16 | P3.7 | bidirectional | Standard I/O port P3.7, multiplexed as external interrupt INT3 (falling edge only), UART1 transmit TxD_2 and comparator positive input CMP+. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STC Micro |
| Package | SOP-16 |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input low voltage (I/O, Schmitt trigger on) | VIL1 | 0.99 | V | Schmitt trigger on; VDD=3.3V, 25℃ | 1852 | ||
| Input low voltage (I/O, Schmitt trigger off) | VIL1 | 1.07 | V | Schmitt trigger off; VDD=3.3V, 25℃ | 1852 | ||
| Input high voltage (general-purpose I/O, Schmitt trigger on) | VIH1 | 1.18 | V | Schmitt trigger on; VDD=3.3V, 25℃ | 1852 | ||
| Input high voltage (general-purpose I/O, Schmitt trigger off) | VIH1 | 1.09 | V | Schmitt trigger off; VDD=3.3V, 25℃ | 1852 | ||
| Logic 0 input current | IIL | 50 | uA | port voltage 0V; VDD=3.3V, 25℃ | 1852 | ||
| Logic 1 to 0 transition current | ITL | 100 | 270 | 600 | uA | port voltage 2.0V; VDD=3.3V, 25℃ | 1852 |
| I/O port pull-up resistor | RPU | 5.8 | 5.9 | 6 | KΩ | VDD=3.3V, 25℃ | 1852 |
| Operating voltage | 1.9 | 5.5 | V | 1851 | |||
| VDD to GND voltage | -0.3 | 5.5 | V | 1851 | |||
| Operating temperature | -40 | 125 | ℃ | Above 85℃ the internal IRC drifts more; external clock recommended | 1851 | ||
| Storage temperature | -55 | 150 | ℃ | 1851 | |||
| I/O port voltage to GND | -0.3 | V | Maximum printed as VDD+0.3 V (not a fixed number) | 1851 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | Accumulator contents and the contents of a sixteen-bit base register, which may be either the Data Pointer or the PC. In the latter case, the PC is incremented to the address of the following | 1043 |
CAD (KiCad official)
- Symbol:
STC8H1K08T-33I-SOP16 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
stc8h1k08t-33i-sop16-etched.step/stc8h1k08t-33i-sop16-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);stc8h1k08t-33i-sop16.step/stc8h1k08t-33i-sop16.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STC Micro datasheet (2180 pp, sha256
046aea020e4685f3, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).