main
Ray
Publish 0.1.0
f00bf25
ST3243CPR
STMicroelectronics · RS232 ICs · SSOP-28
ST3243CPR from STMicroelectronics, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C2+ | passive | Positive terminal of the inverting charge pump capacitor. |
| 2 | C2- | passive | Negative terminal of the inverting charge pump capacitor. |
| 3 | V- | power_out | Inverted voltage of -5.5 V generated by the charge pump. |
| 4 | R1IN | input | First RS-232 receiver input, accepting a voltage range of ±25 V. |
| 5 | R2IN | input | Second RS-232 receiver input, accepting a voltage range of ±25 V. |
| 6 | R3IN | input | Third RS-232 receiver input, accepting a voltage range of ±25 V. |
| 7 | R4IN | input | Fourth RS-232 receiver input, accepting a voltage range of ±25 V. |
| 8 | R5IN | input | Fifth RS-232 receiver input, accepting a voltage range of ±25 V. |
| 9 | T1OUT | output | First RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 10 | T2OUT | output | Second RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 11 | T3OUT | output | Third RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 12 | T3IN | input | Third transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 13 | T2IN | input | Second transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 14 | T1IN | input | First transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 15 | R5OUT | output | Fifth receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 16 | R4OUT | output | Fourth receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 17 | R3OUT | output | Third receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 18 | R2OUT | output | Second receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 19 | R1OUT | output | First receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 20 | R2OUTB | output | Non-inverting complementary receiver output of R2, always active to provide the serial port wake-up function. |
| 21 | INVALID | output | Output of the valid signal detector; logic 1 indicates a valid RS-232 level is present on the receiver inputs. |
| 22 | FORCEOFF | input | Drive low to shut down the transmitters and the on-board power supply, overriding all automatic circuitry and FORCEON. |
| 23 | FORCEON | input | Drive high to override the automatic circuitry and keep the transmitters on; FORCEOFF must be high. |
| 24 | C1- | passive | Negative terminal of the voltage charge pump capacitor. |
| 25 | GND | power_in | Ground reference for the device. |
| 26 | VCC | power_in | Supply voltage, specified for operation from 3 V to 5.5 V (absolute maximum 6 V). |
| 27 | V+ | power_out | Doubled voltage of 5.5 V generated by the charge pump. |
| 28 | C1+ | passive | Positive terminal of the voltage charge pump capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
CAD (KiCad official)
- Symbol:
ST3243CPR - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files:
st3243cpr-etched.step/st3243cpr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);st3243cpr.step/st3243cpr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (18 pp, sha256
1bacb0a9b33761de, retrieved 2026-10-11, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ST3243CPR
**STMicroelectronics** · RS232 ICs · SSOP-28
ST3243CPR from STMicroelectronics, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C2+ | passive | Positive terminal of the inverting charge pump capacitor. |
| 2 | C2- | passive | Negative terminal of the inverting charge pump capacitor. |
| 3 | V- | power_out | Inverted voltage of -5.5 V generated by the charge pump. |
| 4 | R1IN | input | First RS-232 receiver input, accepting a voltage range of ±25 V. |
| 5 | R2IN | input | Second RS-232 receiver input, accepting a voltage range of ±25 V. |
| 6 | R3IN | input | Third RS-232 receiver input, accepting a voltage range of ±25 V. |
| 7 | R4IN | input | Fourth RS-232 receiver input, accepting a voltage range of ±25 V. |
| 8 | R5IN | input | Fifth RS-232 receiver input, accepting a voltage range of ±25 V. |
| 9 | T1OUT | output | First RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 10 | T2OUT | output | Second RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 11 | T3OUT | output | Third RS-232 transmitter output, swinging ±5 V minimum into a 3 kΩ load to GND. |
| 12 | T3IN | input | Third transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 13 | T2IN | input | Second transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 14 | T1IN | input | First transmitter logic input (TTL/CMOS level), with a maximum input voltage of 6 V. |
| 15 | R5OUT | output | Fifth receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 16 | R4OUT | output | Fourth receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 17 | R3OUT | output | Third receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 18 | R2OUT | output | Second receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 19 | R1OUT | output | First receiver logic output, referenced to VCC with a range of -0.3 V to VCC + 0.3 V. |
| 20 | R2OUTB | output | Non-inverting complementary receiver output of R2, always active to provide the serial port wake-up function. |
| 21 | INVALID | output | Output of the valid signal detector; logic 1 indicates a valid RS-232 level is present on the receiver inputs. |
| 22 | FORCEOFF | input | Drive low to shut down the transmitters and the on-board power supply, overriding all automatic circuitry and FORCEON. |
| 23 | FORCEON | input | Drive high to override the automatic circuitry and keep the transmitters on; FORCEOFF must be high. |
| 24 | C1- | passive | Negative terminal of the voltage charge pump capacitor. |
| 25 | GND | power_in | Ground reference for the device. |
| 26 | VCC | power_in | Supply voltage, specified for operation from 3 V to 5.5 V (absolute maximum 6 V). |
| 27 | V+ | power_out | Doubled voltage of 5.5 V generated by the charge pump. |
| 28 | C1+ | passive | Positive terminal of the voltage charge pump capacitor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
## CAD (KiCad official)
- Symbol: `ST3243CPR`
- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`
- 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files: `st3243cpr-etched.step` / `st3243cpr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `st3243cpr.step` / `st3243cpr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590224496411250688) (18 pp, sha256 `1bacb0a9b33761de`, retrieved 2026-10-11, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/st3243cpr-datasheet.pdf)