main
Ray
Publish 0.1.0
d914853
SST26VF040AT-80E
Microchip Tech · NOR FLASH · SOIC-8
SST26VF040AT-80E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CE# | input | Chip Enable: the device is enabled by a high-to-low transition on CE#, and CE# must remain low for the duration of any command sequence or of the command/data input sequence for write operations. |
| 2 | SO/SIO1 | bidirectional | Serial Data Output in SPI mode (default after Power-on Reset or hardware Reset), shifted out on the falling edge of SCK; functions as SIO1 in SQI mode, where it is latched on the rising edge of SCK and is high-impedance during Reset. |
| 3 | WP#/SIO2 | bidirectional | Write-Protect used with the WPEN and IOC bits in the Configuration register to prohibit writes to the Block Protection register, and it only works in SPI single-bit and dual-bit Read mode; functions as SIO2 in quad mode. |
| 4 | Vss | power_in | Ground reference for the device. |
| 5 | SI/SIO0 | bidirectional | Serial Data Input in SPI mode (default after Power-on Reset or hardware Reset), latched on the rising edge of SCK; functions as SIO0 in SQI mode, configured by the Enable Quad I/O (EQIO) command. |
| 6 | SCK | input | Serial Clock: commands, addresses, or input data are latched on the rising edge, and output data is shifted out on the falling edge. |
| 7 | RESET#/HOLD#/SIO3 | bidirectional | Multiplexed pin: RESET# (requires Configuration register bit 6 set to 1) must be driven low for a minimum of TRST to reset the device; HOLD# (factory default, pauses serial communication in SPI single-bit and dual-bit Read modes) must be tied high when not in use; functions as SIO3 in quad mode. |
| 8 | VDD | power_in | Power supply voltage; the device operates from a single power supply of 2.3V-3.6V for write operations, and 2.7V-3.6V or 2.3V-3.6V for read operations. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Read Current | IDDR1 | 8 | 15 | mA | VDD=VDD Max, CE#=0.1VDD/0.9VDD @40 MHz, SO open | 42 | |
| Program and Erase Current | IDDW | 25 | mA | VDD Max | 42 | ||
| Standby Current | ISB1 | 15 | 30 | µA | CE#=VDD, VIN=VDD or VSS | 42 | |
| Standby Current at 125°C | ISB2 | 50 | µA | CE#=VDD, VIN=VDD or VSS at 125°C | 42 | ||
| Deep Power-Down Current | IDPD1 | 8 | 20 | µA | CE#=VDD, VIN=VDD or VSS | 42 | |
| Deep Power-Down Current at 125°C | IDPD2 | 30 | µA | CE#=VDD, VIN=VDD or VSS at 125°C | 42 | ||
| Input Leakage Current | ILI | 2 | µA | VIN=GND to VDD, VDD=VDD Max | 42 | ||
| Output Leakage Current | ILO | 2 | µA | VOUT=GND to VDD, VDD=VDD Max | 42 | ||
| Input Low Voltage | VIL | 0.8 | V | VDD=VDD Min | 42 | ||
| Input High Voltage | VIH | 0.7 | VDD | VDD=VDD Max; printed as 0.7 VDD | 42 | ||
| Output Low Voltage | VOL | 0.2 | V | IOL=100 µA, VDD=VDD Min | 42 | ||
| Output High Voltage | VOH | -0.2 | V | Printed as VDD-0.2 V (offset from VDD); IOH=-100 µA, VDD=VDD Min | 42 | ||
| Output Pin Capacitance | COUT | 8 | pF | VOUT=0V, TA=25°C, f=1 MHz | 42 | ||
| Input Capacitance | CIN | 6 | pF | VIN=0V, TA=25°C, f=1 MHz | 42 | ||
| Endurance | NEND | 100000 | cycles | JEDEC A117 and AEC-Q100-005 | 42 | ||
| Data Retention | TDR | 100 | years | JEDEC A103 and AEC-Q100-005 | 42 | ||
| Latch Up | ILTH | 100 | mA | Printed as 100 + IDD; JEDEC 78 and AEC-Q100-004 | 42 | ||
| Sector Erase | TSE | 25 | ms | VDD=2.3V-3.6V | 42 | ||
| Block Erase | TBE | 25 | ms | VDD=2.3V-3.6V | 42 | ||
| Chip Erase | TSCE | 50 | ms | VDD=2.3V-3.6V | 42 | ||
| Page Program | TPP | 1.5 | ms | VDD=2.3V-3.6V | 42 | ||
| Program Security ID | TPSID | 1.5 | ms | VDD=2.3V-3.6V | 42 | ||
| Write Suspend Latency | TWS | 25 | µs | VDD=2.3V-3.6V | 42 | ||
| Configuration Register Write Latency | TCONFIG | 25 | ms | VDD=2.3V-3.6V | 43 | ||
| Serial Clock Frequency | FCLK | 80 | MHz | 80 MHz column, VDD=2.3V-3.6V | 44 | ||
| Serial Clock Period | TCLK | 12.5 | ns | 80 MHz column, VDD=2.3V-3.6V | 44 | ||
| Serial Clock High Time | TSCKH | 5.5 | ns | 80 MHz column, VDD=2.3V-3.6V | 44 | ||
| Serial Clock Low Time | TSCKL | 5.5 | ns | 80 MHz column, VDD=2.3V-3.6V | 44 | ||
| Serial Clock Rise Time (slew rate) | TSCKR | 0.1 | V/ns | 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL | 44 | ||
| Serial Clock Fall Time (slew rate) | TSCKF | 0.1 | V/ns | 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL | 44 | ||
| CE# Active Setup Time | TCES | 5 | ns | 80 MHz column, relative to SCK | 44 | ||
| CE# Active Hold Time | TCEH | 5 | ns | 80 MHz column, relative to SCK | 44 | ||
| CE# Not Active Setup Time | TCHS | 5 | ns | 80 MHz column, relative to SCK | 44 | ||
| CE# Not Active Hold Time | TCHH | 5 | ns | 80 MHz column, relative to SCK | 44 | ||
| CE# High Time | TCPH | 12.5 | ns | 80 MHz column | 44 | ||
| CE# High-to-High Z Output | TCHZ | 12.5 | ns | 80 MHz column | 44 | ||
| HOLD# Low Setup Time | THLS | 5 | ns | 80 MHz column | 44 | ||
| HOLD# High Setup Time | THHS | 5 | ns | 80 MHz column | 44 | ||
| HOLD# Low Hold Time | THLH | 5 | ns | 80 MHz column | 44 | ||
| HOLD# High Hold Time | THHH | 5 | ns | 80 MHz column | 44 | ||
| HOLD# Low-to-High Z Output | THZ | 8 | ns | 80 MHz column | 44 | ||
| HOLD# High-to-Low Z Output | TLZ | 8 | ns | 80 MHz column | 44 | ||
| Data In Setup Time | TDS | 3 | ns | 80 MHz column | 44 | ||
| Data In Hold Time | TDH | 4 | ns | 80 MHz column | 44 | ||
| Output Hold from SCK Change | TOH | 0 | ns | 80 MHz column | 44 | ||
| Output Valid from SCK | TV | 8 | ns | 80 MHz column; printed 8/5 ns for 30 pF/10 pF load | 44 | ||
| VDD Minimum to Read Operation | TPU-READ | 100 | µs | Power-up | 40 | ||
| VDD Minimum to Write Operation | TPU-WRITE | 100 | µs | Power-up | 40 | ||
| Power-Down Duration | TPD | 100 | ms | Power-down | 40 | ||
| VDD Off | VOFF | 0.3 | V | 0 V recommended | 40 | ||
| Supply Voltage VDD | VDD | 2.3 | 3.6 | V | Extended operating range | 40 | |
| Ambient Temperature (Extended) | TA | -40 | 125 | °C | Extended range; max operating frequency 80 MHz | 40 | |
| Temperature Under Bias | TBIAS | -55 | 125 | °C | Under bias | 40 | |
| Storage Temperature | TSTG | -65 | 150 | °C | 40 | ||
| DC Voltage on Any Pin to Ground | VPIN | -0.5 | 0.5 | V | Printed as -0.5V to VDD+0.5V (max is offset from VDD) | 40 | |
| Transient Voltage on Any Pin to Ground | VPIN-T | -2 | 2 | V | <20 ns; printed as -2.0V to VDD+2.0V (max is offset from VDD) | 40 | |
| Package Power Dissipation Capability | PD | 1 | W | TA=25°C | 40 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 49 |
CAD (KiCad official)
- Symbol:
SST26VF040AT-80E - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
sst26vf040at-80e-etched.step/sst26vf040at-80e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sst26vf040at-80e.step/sst26vf040at-80e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (73 pp, sha256
20b7245e058de3f5, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SST26VF040AT-80E
**Microchip Tech** · NOR FLASH · SOIC-8
SST26VF040AT-80E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CE# | input | Chip Enable: the device is enabled by a high-to-low transition on CE#, and CE# must remain low for the duration of any command sequence or of the command/data input sequence for write operations. |
| 2 | SO/SIO1 | bidirectional | Serial Data Output in SPI mode (default after Power-on Reset or hardware Reset), shifted out on the falling edge of SCK; functions as SIO1 in SQI mode, where it is latched on the rising edge of SCK and is high-impedance during Reset. |
| 3 | WP#/SIO2 | bidirectional | Write-Protect used with the WPEN and IOC bits in the Configuration register to prohibit writes to the Block Protection register, and it only works in SPI single-bit and dual-bit Read mode; functions as SIO2 in quad mode. |
| 4 | Vss | power_in | Ground reference for the device. |
| 5 | SI/SIO0 | bidirectional | Serial Data Input in SPI mode (default after Power-on Reset or hardware Reset), latched on the rising edge of SCK; functions as SIO0 in SQI mode, configured by the Enable Quad I/O (EQIO) command. |
| 6 | SCK | input | Serial Clock: commands, addresses, or input data are latched on the rising edge, and output data is shifted out on the falling edge. |
| 7 | RESET#/HOLD#/SIO3 | bidirectional | Multiplexed pin: RESET# (requires Configuration register bit 6 set to 1) must be driven low for a minimum of TRST to reset the device; HOLD# (factory default, pauses serial communication in SPI single-bit and dual-bit Read modes) must be tied high when not in use; functions as SIO3 in quad mode. |
| 8 | VDD | power_in | Power supply voltage; the device operates from a single power supply of 2.3V-3.6V for write operations, and 2.7V-3.6V or 2.3V-3.6V for read operations. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Read Current | IDDR1 | | 8 | 15 | mA | VDD=VDD Max, CE#=0.1VDD/0.9VDD @40 MHz, SO open | 42 |
| Program and Erase Current | IDDW | | | 25 | mA | VDD Max | 42 |
| Standby Current | ISB1 | | 15 | 30 | µA | CE#=VDD, VIN=VDD or VSS | 42 |
| Standby Current at 125°C | ISB2 | | | 50 | µA | CE#=VDD, VIN=VDD or VSS at 125°C | 42 |
| Deep Power-Down Current | IDPD1 | | 8 | 20 | µA | CE#=VDD, VIN=VDD or VSS | 42 |
| Deep Power-Down Current at 125°C | IDPD2 | | | 30 | µA | CE#=VDD, VIN=VDD or VSS at 125°C | 42 |
| Input Leakage Current | ILI | | | 2 | µA | VIN=GND to VDD, VDD=VDD Max | 42 |
| Output Leakage Current | ILO | | | 2 | µA | VOUT=GND to VDD, VDD=VDD Max | 42 |
| Input Low Voltage | VIL | | | 0.8 | V | VDD=VDD Min | 42 |
| Input High Voltage | VIH | 0.7 | | | VDD | VDD=VDD Max; printed as 0.7 VDD | 42 |
| Output Low Voltage | VOL | | | 0.2 | V | IOL=100 µA, VDD=VDD Min | 42 |
| Output High Voltage | VOH | -0.2 | | | V | Printed as VDD-0.2 V (offset from VDD); IOH=-100 µA, VDD=VDD Min | 42 |
| Output Pin Capacitance | COUT | | | 8 | pF | VOUT=0V, TA=25°C, f=1 MHz | 42 |
| Input Capacitance | CIN | | | 6 | pF | VIN=0V, TA=25°C, f=1 MHz | 42 |
| Endurance | NEND | 100000 | | | cycles | JEDEC A117 and AEC-Q100-005 | 42 |
| Data Retention | TDR | 100 | | | years | JEDEC A103 and AEC-Q100-005 | 42 |
| Latch Up | ILTH | 100 | | | mA | Printed as 100 + IDD; JEDEC 78 and AEC-Q100-004 | 42 |
| Sector Erase | TSE | | | 25 | ms | VDD=2.3V-3.6V | 42 |
| Block Erase | TBE | | | 25 | ms | VDD=2.3V-3.6V | 42 |
| Chip Erase | TSCE | | | 50 | ms | VDD=2.3V-3.6V | 42 |
| Page Program | TPP | | | 1.5 | ms | VDD=2.3V-3.6V | 42 |
| Program Security ID | TPSID | | | 1.5 | ms | VDD=2.3V-3.6V | 42 |
| Write Suspend Latency | TWS | | | 25 | µs | VDD=2.3V-3.6V | 42 |
| Configuration Register Write Latency | TCONFIG | | | 25 | ms | VDD=2.3V-3.6V | 43 |
| Serial Clock Frequency | FCLK | | | 80 | MHz | 80 MHz column, VDD=2.3V-3.6V | 44 |
| Serial Clock Period | TCLK | | | 12.5 | ns | 80 MHz column, VDD=2.3V-3.6V | 44 |
| Serial Clock High Time | TSCKH | 5.5 | | | ns | 80 MHz column, VDD=2.3V-3.6V | 44 |
| Serial Clock Low Time | TSCKL | 5.5 | | | ns | 80 MHz column, VDD=2.3V-3.6V | 44 |
| Serial Clock Rise Time (slew rate) | TSCKR | 0.1 | | | V/ns | 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL | 44 |
| Serial Clock Fall Time (slew rate) | TSCKF | 0.1 | | | V/ns | 80 MHz column; max rise/fall may be limited by TSCKH/TSCKL | 44 |
| CE# Active Setup Time | TCES | 5 | | | ns | 80 MHz column, relative to SCK | 44 |
| CE# Active Hold Time | TCEH | 5 | | | ns | 80 MHz column, relative to SCK | 44 |
| CE# Not Active Setup Time | TCHS | 5 | | | ns | 80 MHz column, relative to SCK | 44 |
| CE# Not Active Hold Time | TCHH | 5 | | | ns | 80 MHz column, relative to SCK | 44 |
| CE# High Time | TCPH | 12.5 | | | ns | 80 MHz column | 44 |
| CE# High-to-High Z Output | TCHZ | | | 12.5 | ns | 80 MHz column | 44 |
| HOLD# Low Setup Time | THLS | 5 | | | ns | 80 MHz column | 44 |
| HOLD# High Setup Time | THHS | 5 | | | ns | 80 MHz column | 44 |
| HOLD# Low Hold Time | THLH | 5 | | | ns | 80 MHz column | 44 |
| HOLD# High Hold Time | THHH | 5 | | | ns | 80 MHz column | 44 |
| HOLD# Low-to-High Z Output | THZ | | | 8 | ns | 80 MHz column | 44 |
| HOLD# High-to-Low Z Output | TLZ | | | 8 | ns | 80 MHz column | 44 |
| Data In Setup Time | TDS | 3 | | | ns | 80 MHz column | 44 |
| Data In Hold Time | TDH | 4 | | | ns | 80 MHz column | 44 |
| Output Hold from SCK Change | TOH | 0 | | | ns | 80 MHz column | 44 |
| Output Valid from SCK | TV | | | 8 | ns | 80 MHz column; printed 8/5 ns for 30 pF/10 pF load | 44 |
| VDD Minimum to Read Operation | TPU-READ | 100 | | | µs | Power-up | 40 |
| VDD Minimum to Write Operation | TPU-WRITE | 100 | | | µs | Power-up | 40 |
| Power-Down Duration | TPD | 100 | | | ms | Power-down | 40 |
| VDD Off | VOFF | | | 0.3 | V | 0 V recommended | 40 |
| Supply Voltage VDD | VDD | 2.3 | | 3.6 | V | Extended operating range | 40 |
| Ambient Temperature (Extended) | TA | -40 | | 125 | °C | Extended range; max operating frequency 80 MHz | 40 |
| Temperature Under Bias | TBIAS | -55 | | 125 | °C | Under bias | 40 |
| Storage Temperature | TSTG | -65 | | 150 | °C | | 40 |
| DC Voltage on Any Pin to Ground | VPIN | -0.5 | | 0.5 | V | Printed as -0.5V to VDD+0.5V (max is offset from VDD) | 40 |
| Transient Voltage on Any Pin to Ground | VPIN-T | -2 | | 2 | V | <20 ns; printed as -2.0V to VDD+2.0V (max is offset from VDD) | 40 |
| Package Power Dissipation Capability | PD | | | 1 | W | TA=25°C | 40 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 49 |
## CAD (KiCad official)
- Symbol: `SST26VF040AT-80E`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files: `sst26vf040at-80e-etched.step` / `sst26vf040at-80e-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sst26vf040at-80e.step` / `sst26vf040at-80e.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/aemDocuments/documents/MPD/ProductDocuments/DataSheets/SST26VF040A-2.5V-3.0V-4-Mbit-Serial-Quad-IO-%28SQI%29-Flash-Memory-20006292B.pdf) (73 pp, sha256 `20b7245e058de3f5`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sst26vf040at-80e-datasheet.pdf)