main
Ray Publish 0.1.0 73c177e

SST25VF040B-50-4C-SAF-T

Microchip Tech · NOR FLASH · SOIC-8

SST25VF040B-50-4C-SAF-T from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: the device is enabled by a high-to-low transition on CE#, and CE# must remain low for the duration of any command sequence.
2 SO output Serial Data Output: transfers data serially out of the device on the falling edge of the serial clock, and outputs Flash busy status during AAI programming when reconfigured as RY/BY#.
3 WP# input Write-Protect: used to enable/disable the BPL bit in the STATUS register.
4 VSS power_in Ground.
5 SI input Serial Data Input: transfers commands, addresses, or data serially into the device, latched on the rising edge of the serial clock.
6 SCK input Serial Clock: provides the timing of the serial interface, with commands, addresses, or input data latched on the rising edge and output data shifted out on the falling edge.
7 HOLD# input Hold: temporarily stops serial communication with the SPI Flash memory without resetting the device.
8 VDD power_in Power Supply: supplies 2.7V-3.6V for the SST25VF040B.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Read Current (25 MHz) IDDR1 10 mA CE# = 0.1 VDD/0.9 VDD@25 MHz, SO = Open 20
Read Current (50 MHz) IDDR2 15 mA CE# = 0.1 VDD/0.9 VDD@50 MHz, SO = Open 20
Program and Erase Current IDDW 30 mA CE# = VDD 20
Standby Current ISB 30 µA CE# = VDD, VIN =VDD or VSS 20
Input Leakage Current ILI 1 µA VIN = GND to VDD, VDD = VDD Max 20
Output Leakage Current ILO 1 µA VOUT = GND to VDD, VDD =VDD Max 20
Input Low Voltage VIL 0.8 V VDD =VDD Min 20
Output Low Voltage VOL1 0.2 V IOL = 100 µA, VDD =VDD Min 20
Output Low Voltage VOL2 0.4 V IOL = 1.6 mA, VDD =VDD Min 20
Output Pin Capacitance COUT 12 pF VOUT = 0V 20
Input Capacitance CIN 6 pF VIN = 0V 20
Endurance NEND 10000 Cycles JEDEC Standard A117 20
Data Retention TDR 100 Years JEDEC Standard A103 20
Serial Clock Frequency FCLK 50 MHz 50 MHz column; Note 1: max clock for Read instruction 03H is 25 MHz 21
Serial Clock High Time TSCKH 9 ns 50 MHz column 21
Serial Clock Low Time TSCKL 9 ns 50 MHz column 21
Serial Clock Rise Time (slew rate) TSCKR 0.1 V/ns 50 MHz column 21
Serial Clock Fall Time (slew rate) TSCKF 0.1 V/ns 50 MHz column 21
CE# Active Setup Time TCES 5 ns 50 MHz column; Relative to SCK 21
CE# Active Hold Time TCEH 5 ns 50 MHz column; Relative to SCK 21
CE# Not Active Setup Time TCHS 5 ns 50 MHz column; Relative to SCK 21
CE# Not Active Hold Time TCHH 5 ns 50 MHz column; Relative to SCK 21
CE# High Time TCPH 50 ns 50 MHz column 21
CE# High-to-High Z Output TCHZ 8 ns 50 MHz column 21
SCK Low-to-Low Z Output TCLZ 0 ns 50 MHz column 21
Data In Setup Time TDS 2 ns 50 MHz column 21
Data In Hold Time TDH 5 ns 50 MHz column 21
HOLD# Low Setup Time THLS 5 ns 50 MHz column 21
HOLD# High Setup Time THHS 5 ns 50 MHz column 21
HOLD# Low Hold Time THLH 5 ns 50 MHz column 21
HOLD# High Hold Time THHH 5 ns 50 MHz column 21
HOLD# Low-to-High Z Output THZ 8 ns 50 MHz column 21
HOLD# High-to-Low Z Output TLZ 8 ns 50 MHz column 21
Output Hold from SCK Change TOH 0 ns 50 MHz column 21
Output Valid from SCK TV 8 ns 50 MHz column 21
Sector Erase TSE 25 ms 50 MHz column 21
Block Erase TBE 25 ms 50 MHz column 21
Chip Erase TSCE 50 ms 50 MHz column 21
Byte Program TBP 10 µs 50 MHz column 21
VDD Minimum to Read Operation TPU-READ 100 µs 18
VDD Minimum to Write Operation TPU-WRITE 100 µs 18
Supply Voltage (Operating Range) VDD 2.7 3.6 V Commercial range (0°C to +70°C) 18
Ambient Temperature (Operating Range) TA 0 70 °C Commercial range 18
Temperature Under Bias -55 125 °C 18
Storage Temperature -65 150 °C 18
DC Voltage on Any Pin to Ground Potential -0.5 V to ground potential; upper limit printed as VDD+0.5V 18
Transient Voltage on Any Pin to Ground Potential -2 V <20 ns; upper limit printed as VDD+2.0V 18
Package Power Dissipation Capability 1 W TA = 25°C 18

CAD (KiCad official)

  • Symbol: SST25VF040B-50-4C-SAF-T
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: sst25vf040b-50-4c-saf-t-etched.step / sst25vf040b-50-4c-saf-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sst25vf040b-50-4c-saf-t.step / sst25vf040b-50-4c-saf-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (31 pp, sha256 1db36dcfe45446b5, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF