main
Ray Publish 0.1.0 d04b7b4

SST25VF016B-50-4I-S2AF-T

Microchip Tech · NOR FLASH · SOIC-8-208mil

SST25VF016B-50-4I-S2AF-T from Microchip Tech, in a SOIC-8-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CE# input Chip Enable: the device is enabled by a high-to-low transition on CE#, which must remain low for the duration of any command sequence.
2 SO output Serial Data Output: transfers data serially out of the device on the falling edge of the serial clock, and outputs flash busy status during AAI programming when reconfigured as RY/BY#.
3 WP# input Write Protect: enables/disables the BPL bit (lock-down function) in the status register.
4 VSS power_in Ground.
5 SI input Serial Data Input: transfers commands, addresses, or data serially into the device, latched on the rising edge of the serial clock.
6 SCK input Serial Clock: provides timing of the serial interface, with inputs latched on the rising edge and output data shifted out on the falling edge (up to 50 MHz).
7 HOLD# input Hold: temporarily stops serial communication with the SPI flash memory without resetting the device.
8 VDD power_in Power supply voltage: 2.7-3.6V for SST25VF016B.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8-208mil
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Read Current IDDR 10 mA CE#=0.1 VDD/0.9 VDD@25 MHz, SO=open 19
Read Current IDDR2 15 mA CE#=0.1 VDD/0.9 VDD@50 MHz, SO=open 19
Read Current IDDR3 20 mA CE#=0.1 VDD/0.9 VDD@50 MHz, SO=open 19
Program and Erase Current IDDW 30 mA CE#=VDD 19
Standby Current ISB 20 µA CE#=VDD, VIN=VDD or VSS 19
Input Leakage Current ILI 1 µA VIN=GND to VDD, VDD=VDD Max 19
Output Leakage Current ILO 1 µA VOUT=GND to VDD, VDD=VDD Max 19
Input Low Voltage VIL 0.8 V VDD=VDD Min 19
Input High Voltage VIH 0.7 VDD VDD=VDD Max 19
Output Low Voltage VOL 0.2 V IOL=100 µA, VDD=VDD Min 19
Output Low Voltage VOL2 0.4 V IOL=1.6 mA, VDD=VDD Min 19
Output High Voltage VOH -0.2 V (relative to VDD) IOH=-100 µA, VDD=VDD Min 19
Output Pin Capacitance COUT 12 pF VOUT = 0V, TA=25°C, F=1 MHz 20
Input Capacitance CIN 6 pF VIN = 0V, TA=25°C, F=1 MHz 20
Endurance NEND 10000 Cycles JEDEC Standard A117 20
Data Retention TDR 100 Years JEDEC Standard A103 20
Latch Up ILTH 100 mA (100 + IDD) JEDEC Standard 78 20
Serial Clock Frequency FCLK 50 MHz 50 MHz column; Read Instruction 03H max is 25 MHz 20
Serial Clock High Time TSCKH 9 ns 50 MHz column 20
Serial Clock Low Time TSCKL 9 ns 50 MHz column 20
Serial Clock Rise Time (Slew Rate) TSCKR 0.1 V/ns 50 MHz column 20
Serial Clock Fall Time (Slew Rate) TSCKF 0.1 V/ns 50 MHz column 20
CE# Active Setup Time TCES 5 ns 50 MHz column, relative to SCK 20
CE# Active Hold Time TCEH 5 ns 50 MHz column, relative to SCK 20
CE# Not Active Setup Time TCHS 5 ns 50 MHz column, relative to SCK 20
CE# Not Active Hold Time TCHH 5 ns 50 MHz column, relative to SCK 20
CE# High Time TCPH 50 ns 50 MHz column 20
CE# High to High-Z Output TCHZ 8 ns 50 MHz column 20
SCK Low to Low-Z Output TCLZ 0 ns 50 MHz column 20
Data In Setup Time TDS 2 ns 50 MHz column 20
Data In Hold Time TDH 5 ns 50 MHz column 20
HOLD# Low Setup Time THLS 5 ns 50 MHz column 20
HOLD# High Setup Time THHS 5 ns 50 MHz column 20
HOLD# Low Hold Time THLH 5 ns 50 MHz column 20
HOLD# High Hold Time THHH 5 ns 50 MHz column 20
HOLD# Low to High-Z Output THZ 8 ns 50 MHz column 20
HOLD# High to Low-Z Output TLZ 8 ns 50 MHz column 20
Output Hold from SCK Change TOH 0 ns 50 MHz column 20
Output Valid from SCK TV 8 ns 50 MHz column 20
Sector-Erase TSE 25 ms 50 MHz column 20
Block-Erase TBE 25 ms 50 MHz column 20
Chip-Erase TSCE 50 ms 50 MHz column 20
Byte-Program TBP 10 µs 50 MHz column 20
Supply Voltage VDD 2.7 3.6 V Operating range, Industrial 19
Ambient Operating Temperature TA -40 85 °C Industrial 19
Temperature Under Bias -55 125 °C 19
Storage Temperature -65 150 °C 19
D.C. Voltage on Any Pin to Ground Potential -0.5 V (max is VDD+0.5) Max is VDD+0.5V 19
Transient Voltage (<20 ns) on Any Pin to Ground Potential -2 V (max is VDD+2.0) Max is VDD+2.0V; <20 ns 19
Package Power Dissipation Capability 1 W TA = 25°C 19
Surface Mount Solder Reflow Temperature 260 °C 10 seconds 19
Output Short Circuit Current 50 mA Output shorted for no more than one second; one output at a time 19

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin S2AF/S2AE1 = SOIC (200 mil Body), 8-lead 1. Suffix E = Matte Tin finish 28

CAD (KiCad official)

  • Symbol: SST25VF016B-50-4I-S2AF-T
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8-208mil (KiCad packages3D, STEP)
  • 3D model files: sst25vf016b-50-4i-s2af-t-etched.step / sst25vf016b-50-4i-s2af-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sst25vf016b-50-4i-s2af-t.step / sst25vf016b-50-4i-s2af-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (30 pp, sha256 066d927d44031dca, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF