main
History Download
Ray spl06-001: CAD wording names the Adom_Gen land, not KiCad official 8b3d5a1

SPL06-001

Goertek · Pressure Sensors · LGA-8

SPL06-001 from Goertek, in a LGA-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 GND power_in Ground pin; connect to the system ground (Figure 8 to Figure 10 application circuits show GND tied to the system ground).
2 CSB input Chip select, active low, with an integrated pull-up; tie to GND for SPI 3-wire, SPI 4-wire and interrupt modes, and tie to VDDIO when I2C is used (not used in I2C).
3 SDA bidirectional Serial data line: data in/out for SPI 3-wire and I2C, and data in only for SPI 4-wire.
4 SCK input Serial clock input for the serial interface (labelled SCL in the I2C application circuit of Figure 8); SPI and I2C timing values are given in Tables 5 and 6, with a maximum I2C clock of 3.4 MHz and a maximum SPI clock of 10 MHz.
5 SDO bidirectional Function depends on interface mode: not used for SPI 3-wire, interrupt output for SPI 3-wire with interrupt, serial data out for SPI 4-wire, and least significant bit of the device address (0x76 when pulled to GND, 0x77 by default) for I2C, which can also carry the interrupt in I2C with interrupt.
6 VDDIO power_in Digital supply voltage for digital blocks and the I/O interface, 1.2 V to 3.6 V.
7 GND power_in Ground pin; connect to the system ground.
8 VDD power_in Supply voltage for analog blocks, 1.7 V to 3.6 V.

Key specifications

Parameter Value
Manufacturer Goertek
Package LGA-8
Category Sensors
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature -40 125 °C 6
Supply Voltage 4 V All pins 6
Voltage at all IO Pins 4 V All pins 6
ESD rating -2 2 kV JESD22-A114 6
Overpressure 10000 hPa 6
Operating temperature TA -40 25 85 °C Operational 6
Operating temperature (full accuracy) TA 0 25 65 °C Full accuracy 6
Operating Pressure P 300 1100 hPa 6
Supply voltage VDD 1.7 3.6 V 6
Interface supply voltage VDDIO 1.2 3.6 V 6
Supply current, Low Power Idd 3 5 uA 1 Hz 6
Supply current, Standard Idd 11 15 uA 1 Hz 6
Supply current, High precision Idd 40 50 uA 1 Hz 6
Peak current Ipeak 400 500 uA During conversion 6
Standby current Iddsbm 1 uA 6
Relative accuracy pressure P_R -6 6 Pa 950…1050hPa, +25…+40°C 7
Relative accuracy pressure P_R -0.5 0.5 m 950…1050hPa, +25…+40°C 7
Absolute accuracy pressure P_A -1 1 hPa 300...1100hPa, 0…+65℃ 7
Noise in pressure, Low Power mode P_Noise 2 5 PaRMS Low Power mode 7
Noise in pressure, Standard mode P_Noise 0.5 1.2 PaRMS Standard mode 7
Noise in pressure, High precision mode P_Noise 0.3 0.6 PaRMS High precision mode 7
Offset temperature coefficient (pressure) TCO -0.5 0.5 Pa/K 1000hPa, +25…+40°C 7
Offset temperature coefficient (altitude) TCO -4.2 4.2 cm/K 1000hPa, +25…+40°C 7
Absolute accuracy temperature -3 1 3 °C 0…+65℃ 7
Pressure/Temperature measurement rate f 1 128 Hz 7
Pressure measurement time, Low Power mode t 5 8 ms Low Power mode 7
Pressure measurement time, Standard mode t 28 35 ms Standard mode 7
Pressure measurement time, High precision mode t 105 115 ms High precision mode 7
Long term stability -1 1 hPa 12 month 7
Supply voltage ramp-up time tvddup 0.001 5 ms Time for supply voltage to reach 90% of final value 7
Serial data clock (I2C) fI2C 3.4 MHz For I2C 7
Serial data clock (SPI) fSPI 10 MHz For SPI 7
Time to sensor ready TSensor_rdy 12 ms SENSOR_RDY bit set when sensor is ready 7
Time to coefficients available TCoef_rdy 40 ms COEF_RDY bit set when coefficients can be read out 7

CAD (Adom-generated)

  • Symbol: SPL06-001
  • Footprint: Adom_Gen:Goertek_SPL06_8b15d6
  • 3D model: generated to fit the land (STEP)
  • 3D model files: spl06-001-etched.step / spl06-001-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); spl06-001.step / spl06-001.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Goertek datasheet (38 pp, sha256 2e502c4bb35ed3b8, retrieved 2026-11-10, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.

Datasheet PDF