SP706TEN-L

{
 "schema": "adom.pads/1",
 "slug": "sp706ten-l",
 "footprint": "SOIC-8_3.9x4.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -1.905
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "MR",
   "type": "input",
   "description": "Manual Reset (active LOW). Triggers a 200ms reset pulse when pulled below 0.8V. Has internal ~70µA pull-up to VCC; can be driven by TTL/CMOS logic or a switch to ground.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "VCC",
   "type": "power_in",
   "description": "Voltage Input. Operating range 1.0V to 5.5V (SP70xT typical 3.0-5.5V). Supply current typically 25µA at 3.3V.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference for all signals.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "PFI",
   "type": "input",
   "description": "Power-Fail comparator Input. When voltage on this pin is less than the 1.25V internal reference, PFO goes LOW. Connect PFI to GND or VCC when unused.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "PFO",
   "type": "output",
   "description": "Power-Fail comparator Output (active LOW). Output is LOW until PFI is greater than 1.25V. Typical drive: ISOURCE=500µA at VCC<3.6V, ISINK=1.2mA.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "WDI",
   "type": "input",
   "description": "Watchdog Input. If this input stays HIGH or LOW for 1.6s, the watchdog times out and WDO goes LOW. Floating WDI or tri-stating it disables the watchdog. Timer clears on any rising/falling edge or while RESET is asserted.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "RESET",
   "type": "output",
   "description": "Active-LOW RESET output. Pulses LOW for 200ms when triggered and stays LOW whenever VCC is below the 3.08V reset threshold. Remains LOW for 200ms after VCC rises above threshold or MR goes HIGH. Watchdog timeout only triggers RESET if WDO is tied to MR.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "WDO",
   "type": "output",
   "description": "Watchdog Output (active LOW). Pulls LOW when the internal 1.6s watchdog timer expires and remains LOW until the watchdog is cleared. Also goes LOW during low-line conditions and while VCC is below the reset threshold; no minimum pulse width. Returns HIGH with no delay once VCC recovers.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}