component
SP3220EBEY-L
Public Made by Adomby adom
MaxLinear Pre-ordered Chips, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSP3220EBEY-L
MaxLinear · Pre-ordered Chips · TSSOP-16
SP3220EBEY-L from MaxLinear, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Receiver enable: apply logic LOW for normal operation, logic HIGH to disable the receiver output (high-Z). |
| 2 | C1+ | passive | Positive terminal of the voltage doubler charge-pump capacitor. |
| 3 | V+ | power_out | +5.5V output generated by the charge pump. |
| 4 | C1- | passive | Negative terminal of the voltage doubler charge-pump capacitor. |
| 5 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 6 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 7 | V- | power_out | -5.5V output generated by the charge pump. |
| 8 | R1IN | input | RS-232 receiver input, with an internal 5kΩ pull-down to ground. |
| 9 | R1OUT | output | TTL/CMOS receiver output. |
| 10 | N.C. | unconnected | No connect. |
| 11 | T1IN | input | TTL/CMOS driver input, with no internal pull-up so unused inputs should be tied to VCC or GND. |
| 12 | N.C. | unconnected | No connect. |
| 13 | T1OUT | output | RS-232 driver output. |
| 14 | GND | power_in | Ground. |
| 15 | VCC | power_in | +3.0V to +5.5V supply voltage. |
| 16 | SHDN | input | Shutdown control input: drive HIGH for normal operation, drive LOW to shut down the driver (high-Z output) and the on-board power supply. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | TSSOP-16 |
| Category | Interface ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Absolute Max | VCC | -0.3 | 6 | V | 2 | ||
| V+ Absolute Max | V+ | -0.3 | 7 | V | NOTE 1 | 2 | |
| V- Absolute Max | V- | -7 | 0.3 | V | NOTE 1 | 2 | |
| V+ + /V-/ | V+ + /V-/ | 13 | V | NOTE 1 | 2 | ||
| ICC (DC VCC or GND current) | ICC | 100 | mA | DC VCC or GND current | 2 | ||
| Input Voltage RxIN | -25 | 25 | V | printed +25V | 2 | ||
| Output Voltage TxOUT | -13.2 | 13.2 | V | printed +13.2V | 2 | ||
| Storage Temperature | -65 | 150 | °C | 2 | |||
| Operating Temperature | -40 | 85 | °C | SP3220EBEY-L ordering information | 18 | ||
| Supply Current | 0.3 | 1 | mA | no load, VCC = 3.3V, TAMB = 25°C, TxIN = GND or VCC | 2 | ||
| Shutdown Supply Current | 1 | 10 | µA | SHDN = GND, VCC = 3.3V, TAMB = 25°C, TxIN = Vcc or GND | 2 | ||
| Input Logic Threshold LOW | 0.8 | V | TxIN, EN, SHDN, Note 2 | 2 | |||
| Input Logic Threshold HIGH | 2 | V | Vcc = 3.3V, Note 2 | 2 | |||
| Input Logic Threshold HIGH | 2.4 | V | Vcc = 5.0V, Note 2 | 2 | |||
| Input Leakage Current | 0.01 | 1 | µA | TxIN, EN, SHDN, TAMB = +25°C, VIN = 0V to VCC | 2 | ||
| Output Leakage Current (receiver) | 0.05 | 10 | µA | Receivers disabled, VOUT = 0V to VCC | 2 | ||
| Output Voltage LOW | 0.4 | V | IOUT = 1.6mA | 2 | |||
| Output Voltage Swing | 5 | 5.4 | V | Driver output loaded with 3KΩ to GND, TAMB = +25°C | 2 | ||
| Driver Output Resistance | 300 | Ω | VCC = V+ = V- = 0V, TOUT=+2V | 3 | |||
| Output Short-Circuit Current | 35 | 60 | mA | VOUT = 0V | 3 | ||
| Driver Output Leakage Current | 25 | µA | VOUT = +12V, VCC = GND to 5.5V, Drivers disabled | 3 | |||
| Receiver Input Voltage Range | -15 | 15 | V | 3 | |||
| Receiver Input Threshold LOW | 0.6 | 1.2 | V | Vcc = 3.3V | 3 | ||
| Receiver Input Threshold LOW | 0.8 | 1.5 | V | Vcc = 5.0V | 3 | ||
| Receiver Input Threshold HIGH | 1.5 | 2.4 | V | Vcc = 3.3V | 3 | ||
| Receiver Input Threshold HIGH | 1.8 | 2.4 | V | Vcc = 5.0V | 3 | ||
| Receiver Input Hysteresis | 0.3 | V | 3 | ||||
| Receiver Input Resistance | 3 | 5 | 7 | kΩ | 3 | ||
| Data Rate SP3220EB | 250 | kbps | RL = 3KΩ, CL = 1000pF | 3 | |||
| Receiver Propagation Delay, tPHL | tPHL | 0.15 | µs | Receiver input to Receiver output, CL = 150pF | 3 | ||
| Receiver Propagation Delay, tPLH | tPLH | 0.15 | µs | Receiver input to Receiver output, CL = 150pF | 3 | ||
| Receiver Output Enable Time | 200 | ns | 3 | ||||
| Receiver Output Disable Time | 200 | ns | 3 | ||||
| Driver Skew | 100 | ns | / tPHL - tPLH /, TAMB = 25°C | 3 | |||
| Receiver Skew | 50 | ns | / tPHL - tPLH / | 3 | |||
| Transition-Region Slew Rate | 30 | V/µs | Vcc = 3.3V, RL = 3kΩ, TAMB = 25°C, -3.0V to +3.0V or +3.0V to -3.0V (SP3220E and SP3220EB) | 3 |
CAD (KiCad official)
- Symbol:
SP3220EBEY-L - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
sp3220ebey-l-etched.step/sp3220ebey-l-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sp3220ebey-l.step/sp3220ebey-l.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (19 pp, sha256
221656b2383cc637, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).