SP3078EEN-L

{
 "schema": "adom.pads/1",
 "slug": "sp3078een-l",
 "footprint": "SOIC-8_3.9x4.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -1.905
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "RO",
   "type": "output",
   "description": "Receiver Output. CMOS-level logic output of the differential receiver comparing A vs B. VOH ≥ VCC-0.6V at IO=-1mA, VOL ≤ 0.4V at IO=1mA. Tri-stated when /RE is high; failsafe HIGH when bus is open, shorted, or idle-terminated.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "/RE",
   "type": "input",
   "description": "Receiver Enable, active-low. Drive LOW to enable the receiver output RO; drive HIGH to tri-state RO. With /RE=VCC and DE=GND the device enters shutdown (ISHDN ≈ 0.05µA typ). Hot-swap glitch protection ensures no false bus assertion during power-up.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "DE",
   "type": "input",
   "description": "Driver Enable, active-high. Drive HIGH to enable the differential driver onto A/B; drive LOW to place A and B into a high-impedance state. Hot-swap glitch protected. VIH ≥ 2V, VIL ≤ 0.8V, 100mV typical hysteresis.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "DI",
   "type": "input",
   "description": "Driver Input. CMOS logic-level input that sets the polarity of the differential A/B outputs when DE is asserted. VIH ≥ 2V, VIL ≤ 0.8V, IIN ±1µA. High on DI drives A high and B low.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference (0V) for both logic and bus sections.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "A",
   "type": "bidirectional",
   "description": "Non-inverting RS-485/RS-422 bus pin. Driver output when DE=HIGH; receiver input when DE=LOW. Common-mode range -7V to +12V, ±15kV Air-Gap/HBM and ±8kV Contact ESD protected. 96kΩ minimum receiver input resistance (1/8 unit load).",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "B",
   "type": "bidirectional",
   "description": "Inverting RS-485/RS-422 bus pin. Driver output when DE=HIGH; receiver input when DE=LOW. Common-mode range -7V to +12V, ±15kV Air-Gap/HBM and ±8kV Contact ESD protected. 96kΩ minimum receiver input resistance (1/8 unit load).",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "VCC",
   "type": "power_in",
   "description": "Supply voltage input, +3.3V ±0.3V (absolute max +6V). Typical supply current 0.8mA (1.5mA max) at no load. Bypass locally to GND with a 0.1µF ceramic capacitor.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}