Generated by kicad-footprint-generator · KiCad file format 20260206
SP211EEA-L
MaxLinear · RS232 ICs · SSOP-28-208mil
SP211EEA-L from MaxLinear, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | T3 OUT | output | RS-232 driver 3 output, which is tri-stated in shutdown with output impedance above 300 ohms and delivers at least ±5V into 3kΩ. |
| 2 | T1 OUT | output | RS-232 driver 1 output, which is tri-stated in shutdown with output impedance above 300 ohms and delivers at least ±5V into 3kΩ. |
| 3 | T2 OUT | output | RS-232 driver 2 output, which is tri-stated in shutdown with output impedance above 300 ohms and delivers at least ±5V into 3kΩ. |
| 4 | R2 IN | input | RS-232 receiver 2 input with an internal 5kΩ pulldown, 0.5V typical hysteresis and an input range of ±25V. |
| 5 | R2 OUT | tri_state | TTL/CMOS receiver 2 output, which is tri-stated by EN high or by shutdown. |
| 6 | T2 IN | input | TTL/CMOS driver 2 input with an internal 400kΩ pull-up to VCC, with VIL max 0.8V and VIH min 2.0V. |
| 7 | T1 IN | input | TTL/CMOS driver 1 input with an internal 400kΩ pull-up to VCC, with VIL max 0.8V and VIH min 2.0V. |
| 8 | R1 OUT | tri_state | TTL/CMOS receiver 1 output, which is tri-stated by EN high or by shutdown. |
| 9 | R1 IN | input | RS-232 receiver 1 input with an internal 5kΩ pulldown, 0.5V typical hysteresis and an input range of ±25V. |
| 10 | GND | power_in | Ground. |
| 11 | VCC | power_in | +5V supply input, specified 4.50V to 5.50V, decoupled with a 0.1µF capacitor. |
| 12 | C1+ | passive | Charge-pump capacitor C1 positive terminal, connected to a 0.1µF capacitor rated 6.3V. |
| 13 | V+ | power_out | Positive charge-pump output of about +7V, connected to a 0.1µF storage capacitor (6.3V if referenced to VCC, 16V if referenced to ground). |
| 14 | C1- | passive | Charge-pump capacitor C1 negative terminal, connected to a 0.1µF capacitor rated 6.3V. |
| 15 | C2+ | passive | Charge-pump capacitor C2 positive terminal, connected to a 0.1µF capacitor rated 16V. |
| 16 | C2- | passive | Charge-pump capacitor C2 negative terminal, connected to a 0.1µF capacitor rated 16V. |
| 17 | V- | power_out | Negative charge-pump output of about -7V, connected to a 0.1µF storage capacitor rated 16V. |
| 18 | R5 IN | input | RS-232 receiver 5 input with an internal 5kΩ pulldown, 0.5V typical hysteresis and an input range of ±25V. |
| 19 | R5 OUT | tri_state | TTL/CMOS receiver 5 output, which is tri-stated by EN high or by shutdown. |
| 20 | T3 IN | input | TTL/CMOS driver 3 input with an internal 400kΩ pull-up to VCC, with VIL max 0.8V and VIH min 2.0V. |
| 21 | T4 IN | input | TTL/CMOS driver 4 input with an internal 400kΩ pull-up to VCC, with VIL max 0.8V and VIH min 2.0V. |
| 22 | R4 OUT | tri_state | TTL/CMOS receiver 4 output, which is tri-stated by EN high or by shutdown. |
| 23 | R4 IN | input | RS-232 receiver 4 input with an internal 5kΩ pulldown, 0.5V typical hysteresis and an input range of ±25V. |
| 24 | EN | input | Receiver enable input, active low: 0V enables the receiver outputs and a high level tri-states them. |
| 25 | SHUTDOWN (SD) | input | Shutdown control input, active high: it turns off the charge pump, tri-states the drivers and receiver outputs, and reduces supply current to 1µA typical (10µA maximum). |
| 26 | R3 OUT | tri_state | TTL/CMOS receiver 3 output, which is tri-stated by EN high or by shutdown. |
| 27 | R3 IN | input | RS-232 receiver 3 input with an internal 5kΩ pulldown, 0.5V typical hysteresis and an input range of ±25V. |
| 28 | T4 OUT | output | RS-232 driver 4 output, which is tri-stated in shutdown with output impedance above 300 ohms and delivers at least ±5V into 3kΩ. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MaxLinear |
| Package | SSOP-28-208mil |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Logic threshold low (VIL) | VIL | 0.8 | V | 7 | |||
| Logic threshold high (VIH) | VIH | 2 | V | 7 | |||
| Logic pull-up current | 15 | 200 | µA | TIN = 0V | 7 | ||
| Maximum transmission rate | 120 | kbps | CL = 1000pF, RL = 3kΩ | 7 | |||
| TTL output low voltage | VOL | 0.4 | V | IOUT = 3.2mA, VCC = 5V | 7 | ||
| TTL output high voltage | VOH | 3.5 | V | IOUT = -1.0mA | 7 | ||
| TTL output leakage current | -10 | 0.05 | 10 | µA | 0V ≤ VOUT ≤ VCC; SP211E EN = 0V; SP213E EN = VCC, TA = +25ºC | 7 | |
| RS-232 output voltage swing (SP211E, SP213E) | -5 | 8.7 | V | All transmitter outputs loaded with 3kΩ to ground | 7 | ||
| Output resistance | 300 | Ω | VCC = 0V, VOUT = ±2V | 7 | |||
| Output short circuit current | -25 | 25 | mA | Infinite Duration, VOUT = 0V | 7 | ||
| RS-232 input voltage range (SP211E, SP213E) | -25 | 25 | V | 7 | |||
| RS-232 input voltage threshold low | 0.8 | 1.2 | V | VCC = 5V, TA = 25°C | 7 | ||
| RS-232 input voltage threshold high | 1.7 | 2.8 | V | VCC = 5V, TA = 25°C | 7 | ||
| RS-232 input hysteresis | 0.2 | 0.5 | 1 | V | VCC = 5V | 7 | |
| RS-232 input resistance | 3 | 5 | 7 | kΩ | VIN = ±15V, TA = 25°C | 7 | |
| Driver propagation delay | 1.5 | µs | 7 | ||||
| Receiver propagation delay | 0.5 | 1.5 | µs | 7 | |||
| Instantaneous slew rate | 30 | V/µs | CL = 50pF, RL = 3 - 7kΩ, TA = 25°C, from ±3V | 7 | |||
| Transition time | 1.5 | µs | CL = 2500pF, RL = 3kΩ, measured from -3V to +3V or +3V to -3V | 7 | |||
| Output enable time | 400 | ns | 7 | ||||
| Output disable time | 250 | ns | 7 | ||||
| Supply voltage VCC | VCC | 4.5 | 5 | 5.5 | V | 8 | |
| Static supply current ICC (SP211E, SP213E) | ICC | 3 | 8 | mA | No load: VCC = ±10%, TA = 25°C | 8 | |
| Supply current with all transmitters loaded (SP211E, SP213E) | ICC | 23 | mA | All transmitters RL = 3kΩ | 8 | ||
| Shutdown current | 1 | 10 | µA | TA = 25°C | 8 | ||
| Operating temperature, Extended (_E) | -40 | 85 | ºC | 8 | |||
| Storage temperature | -65 | 150 | ºC | 8 | |||
| Supply voltage VCC (absolute) | VCC | 6 | V | 6 | |||
| Charge pump supply V+ | V+ | 13.2 | V | 6 | |||
| Charge pump supply V- | V- | 13.2 | V | 6 | |||
| TTL input voltage TIN | TIN | -0.3 | V | 6 | |||
| RS-232 input voltage RIN (SP211E, SP213E) | RIN | -25 | 25 | V | 6 | ||
| TTL/CMOS output voltage ROUT | ROUT | -0.3 | V | 6 | |||
| Power dissipation, 28-pin SSOP | 900 | mW | derate 11.2mW/oC above +70oC | 6 | |||
| Wake-up / power-up wait time | tWAIT | 2 | 3 | ms | VCC = +5V -10%; TA = 25 C | 14 | |
| Receiver enable time | tENABLE | 1 | 2 | ms | VCC = +5V -10%; TA = 25 C | 14 |
CAD (KiCad official)
- Symbol:
SP211EEA-L - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
- 3D model files:
sp211eea-l-etched.step/sp211eea-l-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sp211eea-l.step/sp211eea-l.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MaxLinear datasheet (26 pp, sha256
022d7a1a489cbcc9, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).