3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSN74LS373NE4
Texas Instruments · Latches · PDIP-20
SN74LS373NE4 from Texas Instruments, in a PDIP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OC | input | Active-low buffered output control; when OC is high the eight outputs are forced to the high-impedance state without affecting the latch contents. |
| 2 | 1Q | tri_state | Latch or flip-flop 1 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 3 | 1D | input | Data input to latch or flip-flop 1, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 4 | 2D | input | Data input to latch or flip-flop 2, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 5 | 2Q | tri_state | Latch or flip-flop 2 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 6 | 3Q | tri_state | Latch or flip-flop 3 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 7 | 3D | input | Data input to latch or flip-flop 3, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 8 | 4D | input | Data input to latch or flip-flop 4, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 9 | 4Q | tri_state | Latch or flip-flop 4 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 10 | GND | power_in | Ground reference for the device. |
| 11 | C | input | Enable input for the LS373 latches (transparent while high, latched on falling edge); CLK clock input for the LS374 flip-flops, which load D on the positive transition. |
| 12 | 5Q | tri_state | Latch or flip-flop 5 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 13 | 5D | input | Data input to latch or flip-flop 5, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 14 | 6D | input | Data input to latch or flip-flop 6, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 15 | 6Q | tri_state | Latch or flip-flop 6 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 16 | 7Q | tri_state | Latch or flip-flop 7 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 17 | 7D | input | Data input to latch or flip-flop 7, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 18 | 8D | input | Data input to latch or flip-flop 8, which is transferred to Q while C is high (latch) or on the rising clock edge (flip-flop). |
| 19 | 8Q | tri_state | Latch or flip-flop 8 buffered 3-state bus-driving output, which can drive highly capacitive or low-impedance bus loads. |
| 20 | VCC | power_in | Positive supply voltage pin for the device. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | PDIP-20 |
| Category | Logic |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 4.75 | 5 | 5.25 | V | 6 | |
| High-level output voltage | VOH | 5.5 | V | 6 | |||
| High-level output current | IOH | -2.6 | mA | 6 | |||
| Low-level output current | IOL | 24 | mA | 6 | |||
| Pulse duration CLK high | tw | 15 | ns | CLK high | 6 | ||
| Pulse duration CLK low | tw | 15 | ns | CLK low | 6 | ||
| Data setup time ’LS373 | tsu | 5 | ns | ’LS373, clock edge as printed (↓) | 6 | ||
| Data setup time ’LS374 | tsu | 20 | ns | ’LS374, clock edge as printed (↑) | 6 | ||
| Data hold time ’LS373 | th | 20 | ns | ’LS373, clock edge as printed (↓) | 6 | ||
| Data hold time ’LS374 | th | 0 | ns | ’LS374, data frequency below 10 MHz | 6 | ||
| Operating free-air temperature | TA | 0 | 70 | °C | 6 | ||
| Supply voltage | VCC | 7 | V | ’LS devices, with respect to network ground | 6 | ||
| Input voltage | VI | 7 | V | ’LS devices | 6 | ||
| Off-state output voltage | 5.5 | V | 6 | ||||
| Package thermal impedance | θJA | 69 | °C/W | N package, per JESD 51-7 | 6 | ||
| Storage temperature range | Tstg | -65 | 150 | °C | 6 | ||
| High-level input voltage | VIH | 2 | V | 7 | |||
| Low-level input voltage | VIL | 0.8 | V | 7 | |||
| Input clamp voltage | VIK | -1.5 | V | VCC = MIN, II = -18 mA | 7 | ||
| High-level output voltage | VOH | 2.4 | 3.1 | V | VCC = MIN, VIH = 2 V, VIL = VIL max, IOH = MAX | 7 | |
| Low-level output voltage | VOL | 0.25 | 0.4 | V | VCC = MIN, VIH = 2 V, VIL = VIL max, IOL = 12 mA | 7 | |
| Low-level output voltage | VOL | 0.35 | 0.5 | V | VCC = MIN, VIH = 2 V, VIL = VIL max, IOL = 24 mA | 7 | |
| Off-state output current, high-level voltage applied | IOZH | 20 | µA | VCC = MAX, VIH = 2 V, VO = 2.7 V | 7 | ||
| Off-state output current, low-level voltage applied | IOZL | -20 | µA | VCC = MAX, VIH = 2 V, VO = 0.4 V | 7 | ||
| Input current at maximum input voltage | II | 0.1 | mA | VCC = MAX, VI = 7 V | 7 | ||
| High-level input current | IIH | 20 | µA | VCC = MAX, VI = 2.7 V | 7 | ||
| Low-level input current | IIL | -0.4 | mA | VCC = MAX, VI = 0.4 V | 7 | ||
| Short-circuit output current | IOS | -130 | -30 | mA | VCC = MAX | 7 | |
| Supply current ’LS373 | ICC | 24 | 40 | mA | VCC = MAX, output control at 4.5 V, ’LS373 | 7 | |
| Supply current ’LS374 | ICC | 27 | 40 | mA | VCC = MAX, output control at 4.5 V, ’LS374 | 7 | |
| Maximum clock frequency | fmax | 35 | 50 | MHz | RL = 667 Ω, CL = 45 pF, see Note 3 | 7 | |
| Propagation delay Data to Any Q (tPLH) | tPLH | 12 | 18 | ns | RL = 667 Ω, CL = 45 pF, see Note 3 | 7 | |
| Propagation delay Data to Any Q (tPHL) | tPHL | 12 | 18 | ns | RL = 667 Ω, CL = 45 pF, see Note 3 | 7 | |
| Propagation delay C to Any Q ’LS373 (tPLH) | tPLH | 20 | 30 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS373 | 7 | |
| Propagation delay C to Any Q ’LS373 (tPHL) | tPHL | 18 | 30 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS373 | 7 | |
| Propagation delay CLK to Any Q ’LS374 (tPLH) | tPLH | 15 | 28 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS374 | 7 | |
| Propagation delay CLK to Any Q ’LS374 (tPHL) | tPHL | 19 | 28 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS374 | 7 | |
| Output enable time to high level ’LS373 | tPZH | 15 | 28 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS373 | 7 | |
| Output enable time to high level ’LS374 | tPZH | 20 | 26 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS374 | 7 | |
| Output enable time to low level ’LS373 | tPZL | 25 | 36 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS373 | 7 | |
| Output enable time to low level ’LS374 | tPZL | 21 | 28 | ns | RL = 667 Ω, CL = 45 pF, see Note 3, ’LS374 | 7 | |
| Output disable time from high level ’LS373 | tPHZ | 15 | 25 | ns | RL = 667 Ω, CL = 5 pF, ’LS373 | 7 | |
| Output disable time from high level ’LS374 | tPHZ | 15 | 28 | ns | RL = 667 Ω, CL = 5 pF, ’LS374 | 7 | |
| Output disable time from low level ’LS373 | tPLZ | 12 | 20 | ns | RL = 667 Ω, CL = 5 pF, ’LS373 | 7 | |
| Output disable time from low level ’LS374 | tPLZ | 12 | 20 | ns | RL = 667 Ω, CL = 5 pF, ’LS374 | 7 |
CAD (KiCad official)
- Symbol:
SN74LS373NE4 - Footprint:
Package_DIP:DIP-20_W7.62mm - 3D model: PDIP-20 (KiCad packages3D, STEP)
- 3D model files:
sn74ls373ne4-etched.step/sn74ls373ne4-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn74ls373ne4.step/sn74ls373ne4.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (32 pp, sha256
b1dbdfcaba0d88c4, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).