Generated by kicad-footprint-generator · KiCad file format 20260206
SN74LS160DR
lingxingic · Counters, Dividers · SOP-16
SN74LS160DR from lingxingic, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MR | input | Asynchronous master reset, active LOW: a LOW sets Q0 to Q3 LOW regardless of the levels at CP, PE, CET and CEP. |
| 2 | CP | input | Clock input, triggered on the LOW-to-HIGH edge; all flip-flops are clocked simultaneously on this positive-going edge. |
| 3 | D0 | input | Data input for parallel preset, loaded into Q0 on the positive clock edge when PE is LOW; inputs include clamp diodes so current-limiting resistors can be used for voltages above VCC. |
| 4 | D1 | input | Data input for parallel preset, loaded into Q1 on the positive clock edge when PE is LOW; inputs include clamp diodes so current-limiting resistors can be used for voltages above VCC. |
| 5 | D2 | input | Data input for parallel preset, loaded into Q2 on the positive clock edge when PE is LOW; inputs include clamp diodes so current-limiting resistors can be used for voltages above VCC. |
| 6 | D3 | input | Data input for parallel preset, loaded into Q3 on the positive clock edge when PE is LOW; inputs include clamp diodes so current-limiting resistors can be used for voltages above VCC. |
| 7 | CEP | input | Count enable input; both CEP and CET must be HIGH for the counter to count. |
| 8 | GND | power_in | Ground (0 V) reference for all voltages. |
| 9 | PE | input | Parallel enable input, active LOW: disables counting and loads D0 to D3 into the counter on the positive-going clock edge, regardless of CEP and CET. |
| 10 | CET | input | Count enable carry input; it is also fed forward to enable the terminal count output TC. |
| 11 | Q3 | output | Flip-flop output Q3 of the 4-bit counter; may be preset HIGH or LOW. |
| 12 | Q2 | output | Flip-flop output Q2 of the 4-bit counter; may be preset HIGH or LOW. |
| 13 | Q1 | output | Flip-flop output Q1 of the 4-bit counter; may be preset HIGH or LOW. |
| 14 | Q0 | output | Flip-flop output Q0 of the 4-bit counter; may be preset HIGH or LOW. |
| 15 | TC | output | Terminal count output, HIGH when CET is HIGH and the counter is at terminal count (HLLH); it can be used to enable the next cascaded stage. |
| 16 | VCC | power_in | Supply voltage, 2.0 V minimum, 5.0 V typical and 6.0 V maximum per the recommended operating conditions. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | lingxingic |
| Package | SOP-16 |
| Category | Logic |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| supply voltage | VCC | 2 | 5 | 6 | V | 10 | |
| input transition rise and fall rate | Δt/ΔV | 625 | ns/V | VCC=2.0V | 10 | ||
| input transition rise and fall rate | Δt/ΔV | 1.67 | 139 | ns/V | VCC=4.5V | 10 | |
| input transition rise and fall rate | Δt/ΔV | 83 | ns/V | VCC=6.0V | 10 | ||
| ambient temperature | Tamb | -40 | 125 | ℃ | 10 | ||
| supply voltage | VCC | -0.5 | 7 | V | 9 | ||
| input clamping current | IIK | -20 | 20 | mA | VI < -0.5V or VI > VCC+0.5V | 9 | |
| output clamping current | IOK | -20 | 20 | mA | VO < -0.5V or VO > VCC+0.5V | 9 | |
| output current | IO | -25 | 25 | mA | -0.5V < VO < VCC+0.5V | 9 | |
| supply current | ICC | 50 | mA | 9 | |||
| ground current | IGND | -50 | mA | 9 | |||
| storage temperature | Tstg | -65 | 150 | ℃ | 9 | ||
| total power dissipation | Ptot | 500 | mW | 9 | |||
| soldering temperature | TL | 260 | ℃ | 10s, SOP/TSSOP | 9 | ||
| HIGH-level input voltage | VIH | 1.5 | V | Tamb=-40℃ to +125℃; VCC=2.0V | 12 | ||
| HIGH-level input voltage | VIH | 3.15 | V | Tamb=-40℃ to +125℃; VCC=4.5V | 12 | ||
| HIGH-level input voltage | VIH | 4.2 | V | Tamb=-40℃ to +125℃; VCC=6.0V | 12 | ||
| LOW-level input voltage | VIL | 0.5 | V | Tamb=-40℃ to +125℃; VCC=2.0V | 12 | ||
| LOW-level input voltage | VIL | 1.35 | V | Tamb=-40℃ to +125℃; VCC=4.5V | 12 | ||
| LOW-level input voltage | VIL | 1.8 | V | Tamb=-40℃ to +125℃; VCC=6.0V | 12 | ||
| HIGH-level output voltage | VOH | 1.9 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=-20uA; VCC=2.0V | 12 | ||
| HIGH-level output voltage | VOH | 4.4 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=-20uA; VCC=4.5V | 12 | ||
| HIGH-level output voltage | VOH | 5.9 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=-20uA; VCC=6.0V | 12 | ||
| HIGH-level output voltage | VOH | 3.7 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=-4.0mA; VCC=4.5V | 12 | ||
| HIGH-level output voltage | VOH | 5.2 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=-5.2mA; VCC=6.0V | 12 | ||
| LOW-level output voltage | VOL | 0.1 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=20uA; VCC=2.0V | 12 | ||
| LOW-level output voltage | VOL | 0.4 | V | Tamb=-40℃ to +125℃; VI=VIH or VIL; IO=4.0mA; VCC=4.5V | 12 | ||
| input leakage current | II | -1 | 1 | uA | Tamb=-40℃ to +125℃; VI=VCC or GND; VCC=6.0V | 12 | |
| supply current | ICC | 160 | uA | Tamb=-40℃ to +125℃; VI=VCC or GND; IO=0A; VCC=6.0V | 12 | ||
| propagation delay CP to Qn | tpd | 280 | ns | Tamb=-40℃ to +125℃; CP to Qn; see Figure 8; VCC=2.0V | 17 | ||
| propagation delay CP to Qn | tpd | 56 | ns | Tamb=-40℃ to +125℃; CP to Qn; see Figure 8; VCC=4.5V | 17 | ||
| propagation delay CP to Qn | tpd | 48 | ns | Tamb=-40℃ to +125℃; CP to Qn; see Figure 8; VCC=6.0V | 17 | ||
| propagation delay CP to TC | tpd | 325 | ns | Tamb=-40℃ to +125℃; CP to TC; see Figure 8; VCC=2.0V | 17 | ||
| propagation delay CP to TC | tpd | 65 | ns | Tamb=-40℃ to +125℃; CP to TC; see Figure 8; VCC=4.5V | 17 | ||
| propagation delay CP to TC | tpd | 55 | ns | Tamb=-40℃ to +125℃; CP to TC; see Figure 8; VCC=6.0V | 17 | ||
| propagation delay CET to TC | tpd | 225 | ns | Tamb=-40℃ to +125℃; CET to TC; see Figure 9; VCC=2.0V | 17 | ||
| propagation delay CET to TC | tpd | 45 | ns | Tamb=-40℃ to +125℃; CET to TC; see Figure 9; VCC=4.5V | 17 | ||
| propagation delay CET to TC | tpd | 38 | ns | Tamb=-40℃ to +125℃; CET to TC; see Figure 9; VCC=6.0V | 17 | ||
| High to LOW propagation delay MR to Qn | tPHL | 315 | ns | Tamb=-40℃ to +125℃; MR to Qn; see Figure 10; VCC=2.0V | 17 | ||
| High to LOW propagation delay MR to Qn | tPHL | 63 | ns | Tamb=-40℃ to +125℃; MR to Qn; see Figure 10; VCC=4.5V | 17 | ||
| High to LOW propagation delay MR to Qn | tPHL | 54 | ns | Tamb=-40℃ to +125℃; MR to Qn; see Figure 10; VCC=6.0V | 17 | ||
| High to LOW propagation delay MR to TC | tPHL | 330 | ns | Tamb=-40℃ to +125℃; MR to TC; see Figure 10; VCC=2.0V | 17 | ||
| High to LOW propagation delay MR to TC | tPHL | 66 | ns | Tamb=-40℃ to +125℃; MR to TC; see Figure 10; VCC=4.5V | 17 | ||
| High to LOW propagation delay MR to TC | tPHL | 56 | ns | Tamb=-40℃ to +125℃; MR to TC; see Figure 10; VCC=6.0V | 17 | ||
| transition time | tt | 110 | ns | Tamb=-40℃ to +125℃; see Figure 8 and Figure 9; VCC=2.0V | 17 | ||
| transition time | tt | 22 | ns | Tamb=-40℃ to +125℃; see Figure 8 and Figure 9; VCC=4.5V | 17 | ||
| transition time | tt | 19 | ns | Tamb=-40℃ to +125℃; see Figure 8 and Figure 9; VCC=6.0V | 17 | ||
| pulse width CP HIGH or LOW | tW | 120 | ns | Tamb=-40℃ to +125℃; CP HIGH or LOW; see Figure 8; VCC=2.0V | 17 | ||
| pulse width CP HIGH or LOW | tW | 24 | ns | Tamb=-40℃ to +125℃; CP HIGH or LOW; see Figure 8; VCC=4.5V | 17 | ||
| pulse width CP HIGH or LOW | tW | 20 | ns | Tamb=-40℃ to +125℃; CP HIGH or LOW; see Figure 8; VCC=6.0V | 17 | ||
| pulse width MR LOW | tW | 120 | ns | Tamb=-40℃ to +125℃; MR LOW; see Figure 10; VCC=2.0V | 17 | ||
| pulse width MR LOW | tW | 24 | ns | Tamb=-40℃ to +125℃; MR LOW; see Figure 10; VCC=4.5V | 17 | ||
| pulse width MR LOW | tW | 20 | ns | Tamb=-40℃ to +125℃; MR LOW; see Figure 10; VCC=6.0V | 17 | ||
| recovery time MR to CP | trec | 150 | ns | Tamb=-40℃ to +125℃; MR to CP; see Figure 10; VCC=2.0V | 17 | ||
| recovery time MR to CP | trec | 30 | ns | Tamb=-40℃ to +125℃; MR to CP; see Figure 10; VCC=4.5V | 17 | ||
| recovery time MR to CP | trec | 26 | ns | Tamb=-40℃ to +125℃; MR to CP; see Figure 10; VCC=6.0V | 17 |
CAD (KiCad official)
- Symbol:
SN74LS160DR - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
sn74ls160dr-etched.step/sn74ls160dr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn74ls160dr.step/sn74ls160dr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: lingxingic datasheet (25 pp, sha256
6efaaa26f4a50148, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).