component
SN74HC595BRWNR
Public Made by Adomby adom
Texas Instruments Shift Registers, X1-QFN-16-EP(2.5x2.5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
sn74hc595brwnr: CAD wording names the Adom_Gen land, not KiCad official
a08a0a2
SN74HC595BRWNR
Texas Instruments · Shift Registers · X1-QFN-16-EP(2.5x2.5)
SN74HC595BRWNR from Texas Instruments, in a X1-QFN-16-EP(2.5x2.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | QB | output | QB is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high. |
| 2 | QC | output | QC is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 3 | QD | output | QD is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 4 | QE | output | QE is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 5 | QF | output | QF is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 6 | QG | output | QG is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 7 | QH | output | QH is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 8 | GND | power_in | Ground pin for the device. |
| 9 | QH' | output | QH' is the serial output of the shift register used for daisy chaining; it is not controlled by OE and does not go high-impedance when OE is asserted. |
| 10 | SRCLR | input | Active-low direct clear of the shift register; when low, the shift register is cleared, and the input is over-voltage tolerant independent of VCC. |
| 11 | SRCLK | input | Shift-register clock input; the shift register is positive-edge triggered on SRCLK. |
| 12 | RCLK | input | Storage-register clock input; the storage register is positive-edge triggered on RCLK, transferring shift-register data to the storage register. |
| 13 | OE | input | Output enable; when high, outputs QA through QH are placed in the high-impedance state (QH' is not affected), and when low they are enabled. |
| 14 | SER | input | Serial data input to the first shift-register stage; inputs are over-voltage tolerant independent of VCC. |
| 15 | QA | output | QA is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 16 | VCC | power_in | Supply voltage, specified for 2 V to 6 V over the recommended operating free-air temperature range. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | X1-QFN-16-EP(2.5x2.5) |
| Category | Logic |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.5 | 7 | V | 4 | ||
| Input voltage | VI | -0.5 | 7 | V | 4 | ||
| Input clamp current | IIK | -20 | mA | VI < 0 | 4 | ||
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VCC | 4 | |
| Continuous output current | IO | -35 | 35 | mA | VO = 0 to VCC | 4 | |
| Continuous current through VCC or GND | -70 | 70 | mA | 4 | |||
| Junction temperature | TJ | 150 | °C | 4 | |||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| Supply voltage | VCC | 2 | 5 | 6 | V | 4 | |
| High-level input voltage | VIH | 1.5 | V | VCC = 2 V | 4 | ||
| High-level input voltage | VIH | 3.15 | V | VCC = 4.5 V | 4 | ||
| High-level input voltage | VIH | 4.2 | V | VCC = 6 V | 4 | ||
| Low-level input voltage | VIL | 0.5 | V | VCC = 2 V | 4 | ||
| Low-level input voltage | VIL | 1.35 | V | VCC = 4.5 V | 4 | ||
| Low-level input voltage | VIL | 1.8 | V | VCC = 6 V | 4 | ||
| Input voltage | VI | 0 | V | max = VCC (not numeric) | 4 | ||
| Output voltage | VO | 0 | V | max = VCC (not numeric) | 4 | ||
| Input transition rise or fall time | Δt/Δv | 1000 | ns | VCC = 2 V | 4 | ||
| Input transition rise or fall time | Δt/Δv | 500 | ns | VCC = 4.5 V | 4 | ||
| Input transition rise or fall time | Δt/Δv | 400 | ns | VCC = 6 V | 4 | ||
| Operating free-air temperature | TA | -55 | 125 | °C | 4 | ||
| High-level output voltage QH′ | VOH | 1.9 | 1.998 | V | VI = VIH or VIL; IOH = −20 μA; VCC = 2 V | 5 | |
| High-level output voltage QA-QH | VOH | 4.4 | 4.499 | V | VI = VIH or VIL; IOH = −20 μA; VCC = 4.5 V | 5 | |
| High-level output voltage QA-QH | VOH | 5.9 | 5.999 | V | VI = VIH or VIL; IOH = −20 μA; VCC = 6 V | 5 | |
| High-level output voltage QH′ | VOH | 3.7 | 4.3 | V | VI = VIH or VIL; IOH = −4 mA; VCC = 4.5 V | 5 | |
| High-level output voltage QA-QH | VOH | 3.7 | 4.3 | V | VI = VIH or VIL; IOH = −6 mA; VCC = 4.5 V | 5 | |
| High-level output voltage QH′ | VOH | 5.2 | 5.8 | V | VI = VIH or VIL; IOH = −5.2 mA; VCC = 6 V | 5 | |
| High-level output voltage QA-QH | VOH | 5.2 | 5.8 | V | VI = VIH or VIL; IOH = −7.8 mA; VCC = 6 V | 5 | |
| Low-level output voltage | VOL | 0.002 | 0.1 | V | VI = VIH or VIL; IOL = 20 μA; VCC = 2 V | 5 | |
| Low-level output voltage | VOL | 0.001 | 0.1 | V | VI = VIH or VIL; IOL = 20 μA; VCC = 4.5 V | 5 | |
| Low-level output voltage QH′ | VOL | 0.17 | 0.4 | V | VI = VIH or VIL; IOL = 4 mA; VCC = 4.5 V | 5 | |
| Low-level output voltage QA-QH | VOL | 0.17 | 0.4 | V | VI = VIH or VIL; IOL = 6 mA; VCC = 4.5 V | 5 | |
| Low-level output voltage QH′ | VOL | 0.15 | 0.4 | V | VI = VIH or VIL; IOL = 5.2 mA; VCC = 6 V | 5 | |
| Low-level output voltage QA-QH | VOL | 0.15 | 0.4 | V | VI = VIH or VIL; IOL = 7.8 mA; VCC = 6 V | 5 | |
| Input current | II | -1000 | 0.1 | 1000 | nA | VI = VCC or 0; VCC = 6 V | 5 |
| Off-state (high-impedance) output current | IOZ | -10 | 0.01 | 10 | μA | VO = VCC or 0; QA-QH; VCC = 6 V | 5 |
| Supply current | ICC | 8 | 160 | μA | VI = VCC or 0; IO = 0; VCC = 6 V | 5 | |
| Input capacitance | Ci | 3 | 10 | pF | VCC = 2 V to 6 V | 5 | |
| Clock frequency SRCLK/RCLK | fclock | 4.2 | MHz | VCC = 2 V | 6 | ||
| Clock frequency SRCLK/RCLK | fclock | 21 | MHz | VCC = 4.5 V | 6 | ||
| Clock frequency SRCLK/RCLK | fclock | 25 | MHz | VCC = 6 V | 6 | ||
| Pulse duration SRCLK or RCLK high or low | tw | 120 | ns | VCC = 2 V | 6 | ||
| Pulse duration SRCLK or RCLK high or low | tw | 24 | ns | VCC = 4.5 V | 6 | ||
| Pulse duration SRCLK or RCLK high or low | tw | 20 | ns | VCC = 6 V | 6 | ||
| Set-up time SER before SRCLK↑ | tsu | 150 | ns | VCC = 2 V | 6 | ||
| Set-up time SER before SRCLK↑ | tsu | 30 | ns | VCC = 4.5 V | 6 | ||
| Set-up time SER before SRCLK↑ | tsu | 25 | ns | VCC = 6 V | 6 | ||
| Propagation delay SRCLK to QH′ | tpd | 50 | 240 | ns | CL = 50 pF; VCC = 2 V | 7 | |
| Propagation delay SRCLK to QH′ | tpd | 17 | 48 | ns | CL = 50 pF; VCC = 4.5 V | 7 | |
| Propagation delay SRCLK to QH′ | tpd | 14 | 41 | ns | CL = 50 pF; VCC = 6 V | 7 | |
| Junction-to-ambient thermal resistance | RθJA | 112 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJCtop | 47.9 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 72.4 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 0.6 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 72.4 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJCbot | 32.2 | °C/W | 5 |
CAD (Adom-generated)
- Symbol:
SN74HC595BRWNR - Footprint:
Adom_Gen:Texas_Instruments_SN74_9f8751 - 3D model: generated to fit the land (STEP)
- 3D model files:
sn74hc595brwnr-etched.step/sn74hc595brwnr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sn74hc595brwnr.step/sn74hc595brwnr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (24 pp, sha256
8ffaedcf8970a9e0, retrieved 2026-11-06, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.
# SN74HC595BRWNR
**Texas Instruments** · Shift Registers · X1-QFN-16-EP(2.5x2.5)
SN74HC595BRWNR from Texas Instruments, in a X1-QFN-16-EP(2.5x2.5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table and the footprint is an Adom_Gen land derived from the manufacturer drawing; the 3D model is generated to fit it.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | QB | output | QB is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high. |
| 2 | QC | output | QC is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 3 | QD | output | QD is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 4 | QE | output | QE is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 5 | QF | output | QF is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 6 | QG | output | QG is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 7 | QH | output | QH is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 8 | GND | power_in | Ground pin for the device. |
| 9 | QH' | output | QH' is the serial output of the shift register used for daisy chaining; it is not controlled by OE and does not go high-impedance when OE is asserted. |
| 10 | SRCLR | input | Active-low direct clear of the shift register; when low, the shift register is cleared, and the input is over-voltage tolerant independent of VCC. |
| 11 | SRCLK | input | Shift-register clock input; the shift register is positive-edge triggered on SRCLK. |
| 12 | RCLK | input | Storage-register clock input; the storage register is positive-edge triggered on RCLK, transferring shift-register data to the storage register. |
| 13 | OE | input | Output enable; when high, outputs QA through QH are placed in the high-impedance state (QH' is not affected), and when low they are enabled. |
| 14 | SER | input | Serial data input to the first shift-register stage; inputs are over-voltage tolerant independent of VCC. |
| 15 | QA | output | QA is a parallel 3-state output of the 8-bit storage register, placed high-impedance when OE is high; continuous output current is limited to ±35 mA. |
| 16 | VCC | power_in | Supply voltage, specified for 2 V to 6 V over the recommended operating free-air temperature range. |
| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | X1-QFN-16-EP(2.5x2.5) |
| Category | Logic |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.5 | | 7 | V | | 4 |
| Input voltage | VI | -0.5 | | 7 | V | | 4 |
| Input clamp current | IIK | -20 | | | mA | VI < 0 | 4 |
| Output clamp current | IOK | -20 | | 20 | mA | VO < 0 or VO > VCC | 4 |
| Continuous output current | IO | -35 | | 35 | mA | VO = 0 to VCC | 4 |
| Continuous current through VCC or GND | | -70 | | 70 | mA | | 4 |
| Junction temperature | TJ | | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| Supply voltage | VCC | 2 | 5 | 6 | V | | 4 |
| High-level input voltage | VIH | 1.5 | | | V | VCC = 2 V | 4 |
| High-level input voltage | VIH | 3.15 | | | V | VCC = 4.5 V | 4 |
| High-level input voltage | VIH | 4.2 | | | V | VCC = 6 V | 4 |
| Low-level input voltage | VIL | | | 0.5 | V | VCC = 2 V | 4 |
| Low-level input voltage | VIL | | | 1.35 | V | VCC = 4.5 V | 4 |
| Low-level input voltage | VIL | | | 1.8 | V | VCC = 6 V | 4 |
| Input voltage | VI | 0 | | | V | max = VCC (not numeric) | 4 |
| Output voltage | VO | 0 | | | V | max = VCC (not numeric) | 4 |
| Input transition rise or fall time | Δt/Δv | | | 1000 | ns | VCC = 2 V | 4 |
| Input transition rise or fall time | Δt/Δv | | | 500 | ns | VCC = 4.5 V | 4 |
| Input transition rise or fall time | Δt/Δv | | | 400 | ns | VCC = 6 V | 4 |
| Operating free-air temperature | TA | -55 | | 125 | °C | | 4 |
| High-level output voltage QH′ | VOH | 1.9 | 1.998 | | V | VI = VIH or VIL; IOH = −20 μA; VCC = 2 V | 5 |
| High-level output voltage QA-QH | VOH | 4.4 | 4.499 | | V | VI = VIH or VIL; IOH = −20 μA; VCC = 4.5 V | 5 |
| High-level output voltage QA-QH | VOH | 5.9 | 5.999 | | V | VI = VIH or VIL; IOH = −20 μA; VCC = 6 V | 5 |
| High-level output voltage QH′ | VOH | 3.7 | 4.3 | | V | VI = VIH or VIL; IOH = −4 mA; VCC = 4.5 V | 5 |
| High-level output voltage QA-QH | VOH | 3.7 | 4.3 | | V | VI = VIH or VIL; IOH = −6 mA; VCC = 4.5 V | 5 |
| High-level output voltage QH′ | VOH | 5.2 | 5.8 | | V | VI = VIH or VIL; IOH = −5.2 mA; VCC = 6 V | 5 |
| High-level output voltage QA-QH | VOH | 5.2 | 5.8 | | V | VI = VIH or VIL; IOH = −7.8 mA; VCC = 6 V | 5 |
| Low-level output voltage | VOL | | 0.002 | 0.1 | V | VI = VIH or VIL; IOL = 20 μA; VCC = 2 V | 5 |
| Low-level output voltage | VOL | | 0.001 | 0.1 | V | VI = VIH or VIL; IOL = 20 μA; VCC = 4.5 V | 5 |
| Low-level output voltage QH′ | VOL | | 0.17 | 0.4 | V | VI = VIH or VIL; IOL = 4 mA; VCC = 4.5 V | 5 |
| Low-level output voltage QA-QH | VOL | | 0.17 | 0.4 | V | VI = VIH or VIL; IOL = 6 mA; VCC = 4.5 V | 5 |
| Low-level output voltage QH′ | VOL | | 0.15 | 0.4 | V | VI = VIH or VIL; IOL = 5.2 mA; VCC = 6 V | 5 |
| Low-level output voltage QA-QH | VOL | | 0.15 | 0.4 | V | VI = VIH or VIL; IOL = 7.8 mA; VCC = 6 V | 5 |
| Input current | II | -1000 | 0.1 | 1000 | nA | VI = VCC or 0; VCC = 6 V | 5 |
| Off-state (high-impedance) output current | IOZ | -10 | 0.01 | 10 | μA | VO = VCC or 0; QA-QH; VCC = 6 V | 5 |
| Supply current | ICC | | 8 | 160 | μA | VI = VCC or 0; IO = 0; VCC = 6 V | 5 |
| Input capacitance | Ci | | 3 | 10 | pF | VCC = 2 V to 6 V | 5 |
| Clock frequency SRCLK/RCLK | fclock | | | 4.2 | MHz | VCC = 2 V | 6 |
| Clock frequency SRCLK/RCLK | fclock | | | 21 | MHz | VCC = 4.5 V | 6 |
| Clock frequency SRCLK/RCLK | fclock | | | 25 | MHz | VCC = 6 V | 6 |
| Pulse duration SRCLK or RCLK high or low | tw | 120 | | | ns | VCC = 2 V | 6 |
| Pulse duration SRCLK or RCLK high or low | tw | 24 | | | ns | VCC = 4.5 V | 6 |
| Pulse duration SRCLK or RCLK high or low | tw | 20 | | | ns | VCC = 6 V | 6 |
| Set-up time SER before SRCLK↑ | tsu | 150 | | | ns | VCC = 2 V | 6 |
| Set-up time SER before SRCLK↑ | tsu | 30 | | | ns | VCC = 4.5 V | 6 |
| Set-up time SER before SRCLK↑ | tsu | 25 | | | ns | VCC = 6 V | 6 |
| Propagation delay SRCLK to QH′ | tpd | | 50 | 240 | ns | CL = 50 pF; VCC = 2 V | 7 |
| Propagation delay SRCLK to QH′ | tpd | | 17 | 48 | ns | CL = 50 pF; VCC = 4.5 V | 7 |
| Propagation delay SRCLK to QH′ | tpd | | 14 | 41 | ns | CL = 50 pF; VCC = 6 V | 7 |
| Junction-to-ambient thermal resistance | RθJA | | 112 | | °C/W | | 5 |
| Junction-to-case (top) thermal resistance | RθJCtop | | 47.9 | | °C/W | | 5 |
| Junction-to-board thermal resistance | RθJB | | 72.4 | | °C/W | | 5 |
| Junction-to-top characterization parameter | ψJT | | 0.6 | | °C/W | | 5 |
| Junction-to-board characterization parameter | ψJB | | 72.4 | | °C/W | | 5 |
| Junction-to-case (bottom) thermal resistance | RθJCbot | | 32.2 | | °C/W | | 5 |
## CAD (Adom-generated)
- Symbol: `SN74HC595BRWNR`
- Footprint: `Adom_Gen:Texas_Instruments_SN74_9f8751`
- 3D model: generated to fit the land (STEP)
- 3D model files: `sn74hc595brwnr-etched.step` / `sn74hc595brwnr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sn74hc595brwnr.step` / `sn74hc595brwnr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/sn74hc595b.pdf) (24 pp, sha256 `8ffaedcf8970a9e0`, retrieved 2026-11-06, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing. 3D model generated to fit that land.
[Datasheet PDF](docs/sn74hc595brwnr-datasheet.pdf)