main
History Download
Ray Publish 0.1.0 6fa2cfe

SN6507DGQRQ1

Texas Instruments · Power Management - Specialized · HVSSOP-10

SN6507DGQRQ1 from Texas Instruments, in a HVSSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SW1 output Open-drain output of the first power MOSFET (switch 1), typically connected to either outer terminal of the center-tap transformer, with external traces kept short because of large currents.
2 GND power_in Ground connection for the internal control circuits and power MOSFET; pin 2 and pin 9 must be shorted on the PCB for optimized emissions and efficiency.
3 VCC power_in Main supply pin for the power and analog circuits, specified at 3 V to 36 V in the recommended operating conditions, and it sees short high-current pulses during power-switch turn-on and turn-off.
4 EN/UVLO input Enable and undervoltage-lockout programming input; the device switches only when this pin is above the EN/UVLO threshold (1.5 V typical rising) and VCC is above its UVLO threshold, and it stops switching when floating or below the threshold.
5 DC input Duty-cycle control input where a resistor to GND sets the duty cycle; leaving it floating selects the 48% typical default, and duty-cycle control is disabled in SYNC mode.
6 SR input Slew-rate control input where a resistor to GND sets the slew rate of SW1 and SW2 (RSR 4.8 kΩ to 21 kΩ), floating selects the default slew rate, and a short to GND is treated as a fault that stops switching.
7 CLK input External clock input for SYNC mode or frequency-program pin, where a resistor to GND (4 kΩ to 111 kΩ) sets the switching frequency, a short to GND selects the 1 MHz default, and a floating pin stops switching.
8 SS/ILIM input Multifunction soft-start and current-limit pin, where a capacitor to GND (0.05 µF to 10 µF recommended) sets the soft-start time and a resistor to GND (18 kΩ to 261 kΩ) sets the programmable current limit, and both must be present.
9 GND power_in Ground connection for the internal control circuits and power MOSFET; pin 9 and pin 2 must be shorted on the PCB for optimized emissions and efficiency.
10 SW2 output Open-drain output of the second power MOSFET (switch 2), typically connected to either outer terminal of the center-tap transformer, with external traces kept short because of large currents.
11 PowerPAD power_in Exposed thermal pad that must be electrically connected to GND pins 2 and 9 on the printed circuit board for proper operation.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package HVSSOP-10
Category Power Management (PMIC)
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC -0.5 60 V 4
Voltage EN/UVLO EN/UVLO -0.5 V 4
Voltage SS/ILIM, CLK, DC SS/ILIM, CLK, DC -0.5 6 V 4
Output switch voltage SW1, SW2 SW1, SW2 85 V 4
Peak output switch current I(D1)Pk, I(D2)Pk 1.6 A 4
Junction temperature TJ -55 150 °C 4
Storage temperature range Tstg -65 150 °C 4
VCC Input Voltage VCC 3 36 V 4
Output switch current - Primary side ISW1, ISW2 0.4 A 3 V < VCC < 6 V 4
Output switch current - Primary side ISW1, ISW2 0.5 A 6 V < VCC < 36 V 4
Ambient temperature TA -55 125 °C 4
Junction temperature TJ -55 150 °C 4
Soft-start capacitor on SS/ILIM pin CSS 0.05 10 µF 4
Current limiting resistor on SS/ILIM pin RILIM 18 261 kΩ 4
Resistor on SR pin for Slew rate control RSR 4.8 21 kΩ 4
Resistor on CLK pin for programmable frequency RCLK 4 111 kΩ 4
VIN supply current (not incl. switch drive currents) Icc 3 4 mA 3 V < VCC < 36 V, VEN/UVLO=2.5 V, RL = 50 Ω 5
VIN shutdown current ISHUTDOWN 0.8 2.5 µA VEN/UVLO=0 V, RL = 50 Ω 5
Leakage current on SS/ILIM pin ILKG(SS/ILIM) 0.7 µA VEN/UVLO = 0 V, Voltage of SS/ILIM = 5 V 5
VCC positive-going UVLO threshold VCCUVLO-RISING 2.8 2.9 V VCC rising, EN/UVLO is shorted to VCC 5
VCC negative-going UVLO threshold VCCUVLO-FALLING 2.5 2.67 V VCC falling, EN/UVLO is shorted to VCC 5
VCC UVLO threshold hysteresis VCCUVLO-HYS 0.1 0.12 V EN/UVLO is shorted to VCC 5
EN/UVLO positive-going UVLO threshold ENUVLO-RISING 1.4 1.5 1.6 V EN/UVLO rising 5
EN/UVLO negative-going UVLO threshold ENUVLO-FALLING 1.25 1.35 1.45 V EN/UVLO falling 5
EN/UVLO UVLO threshold hysteresis ENUVLO-HYS 0.14 0.15 V 5
Average ON time mismatch between SW1 and SW2 DMM 0 % RL = 50 Ω to VCC, Pull-Up Resistor Test Circuit Configuration 5
Output switch ON resistance R(ON) 0.45 1 Ω VCC = 24 V, ISW1, ISW2 = 0.5 A 5
D1, D2 average switching frequency (Default) FSW 780 1000 1296 kHz RL = 50 Ω, RCLK = 0 kΩ, Pull-Up Resistor Test Circuit Configuration 5
External clock frequency on CLK pin F(SYNC) 200 4000 kHz External clock applied on CLK pin for SYNC mode 5
CLK pin logic high threshold VCLK(High) 1.6 1.8 V 5
CLK pin logic low threshold VCLK(Low) 1 1.2 V 5
SS ext capacitor range CSS Range 0.05 5 µF 5
SW1 and SW2 current limit ILIM 1 1.3 1.59 A RLIM = 18.2 kΩ, 5 V < VCC < 36 V 5
SW1 and SW2 current limit ILIM 0.56 0.79 1.02 A RLIM = 30.1 kΩ, 5 V < VCC < 36 V 5
SW1 and SW2 current limit ILIM 0.06 0.1 0.14 A RLIM = 261 kΩ, 5 V < VCC < 36 V 5
Input OVLO rising threshold VCCOVLO-RISING 36.9 38.7 40.5 V VCC rising 6
Input OVLO falling threshold VCCOVLO-FALLING 36.5 38.2 40 V VCC falling 6
Input OVLO hysteresis VCCOVLO-HYS 0.47 0.57 V VCC hysteresis voltage 6
TSD turn on temperature TSD+ 170 184 198 °C TJ rising 6
TSD turn off temperature TSD- 135 147 159 °C TJ falling 6
TSD hysteresis TSD-HYST 32 37 42 °C 6
Power-up time tPWRUP 300 400 µs CSS = 0 µF, from EN = High to full drive-current available at SW1 and SW2 7
Power-down time tPWRDN 30 µs CSS = 0 µF, from EN = Low to output MOSFETs off (no current on SW1 and SW2) 7
Junction-to-ambient thermal resistance RθJA 48.2 °C/W 4
Junction-to-case (top) thermal resistance RθJC(top) 61.6 °C/W 4
Junction-to-board thermal resistance RθJB 18.4 °C/W 4
Junction-to-top characterization parameter ψJT 1.7 °C/W 4
Junction-to-board characterization parameter ψJB 18.3 °C/W 4
Junction-to-case (bottom) thermal resistance RθJC(bottom) 5.8 °C/W 4
Switch slew rate on SW1 and SW2 V(SLEW) 298 V/µs RL = 50 Ω to VCC, VCC = 12 V; RSR = 9.6 kΩ (Default), Pull-Up Resistor Test Circuit Configuration 5
Switch slew rate on SW1 and SW2 V(SLEW) 369 V/µs RL = 50 Ω to VCC, VCC = 12 V; RSR = 9.6 kΩ (Default), Pull-Up Resistor Test Circuit Configuration 5
Switching duty cycle on SW1 and SW2 Dsw1, Dsw2 48 % DC pin floating (Default), FSW = 300KHz, Timing Diagram 6
SS ext capacitor charging current ISS 275 µA 5
EN glitch filter TEN_glitch 5 µs 7
Break-before-make time tBBM 70 ns Measured at 0.5VCC with RL = 50 Ω, FSW = 1 MHz, RSR = 9.6 kΩ (or Default), Timing Diagram 7

CAD (KiCad official)

  • Symbol: SN6507DGQRQ1
  • Footprint: Package_SO:HVSSOP-10-1EP_3x3mm_P0.5mm_EP1.83x1.89mm
  • 3D model: HVSSOP-10, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.0 mm tall, family nominal (no datasheet A read)). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: sn6507dgqrq1-etched.step / sn6507dgqrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sn6507dgqrq1.step / sn6507dgqrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (44 pp, sha256 750f94554cd548d8, retrieved 2026-11-10, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF