3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSIT8924BM-71-33E-50.000000G
SiTime · Pre-programmed Oscillators · SMD2016-4P
SIT8924BM-71-33E-50.000000G from SiTime, in a SMD2016-4P. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OE/ST/NC | input | Factory-programmed as Output Enable (OE): logic High gives the specified frequency output and logic Low puts the output in high impedance, or as Standby (ST): logic Low puts the device in sleep with supply current reduced to Istd and output weakly pulled down, or as No Connect (NC): any voltage between 0 and Vdd or open, with no function. Input levels are VIH at least 70% Vdd and VIL at most 30% Vdd, and a pull-up of 10 kΩ or less is recommended in OE/ST mode if the pin is not externally driven. |
| 2 | GND | power_in | Electrical ground; a capacitor of 0.1 µF or higher is required between Vdd and GND. |
| 3 | OUT | output | LVCMOS/LVTTL oscillator output with 45% to 55% duty cycle at all Vdd levels and rise/fall times of 3 ns maximum at Vdd = 2.25 V to 3.63 V (20% to 80%). |
| 4 | VDD | power_in | Power supply voltage of 1.62 V to 1.98 V for 1.8 V operation, or 2.25 V to 3.63 V for the other supported voltages, with a capacitor of 0.1 µF or higher required between Vdd and GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SiTime |
| Package | SMD2016-4P |
| Category | Crystals/Oscillators/Resonators |
| Pins | 4 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Frequency Range | f | 1 | 110 | MHz | Refer to Table 13 to 15 for a list supported frequencies | 1 | |
| Frequency Stability | F_stab | -20 | 20 | ppm | Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and variations over operating temperature, rated power supply voltage and load (15 pF ±10%) | 1 | |
| Operating Temperature Range (ambient) | T_use | -55 | 125 | °C | Extended cold AEC-Q100 Grade1 (temperature option M) | 1 | |
| Supply Voltage | Vdd | 2.25 | 3.63 | V | All voltages between 2.25V and 3.63V including 2.5V, 2.8V, 3.0V and 3.3V are supported | 1 | |
| Current Consumption | Idd | 4 | 4.8 | mA | No load condition, f = 20 MHz, Vdd = 2.25V to 3.63V | 1 | |
| OE Disable Current | I_od | 4.5 | mA | Vdd = 2.5V to 3.3V, OE = Low, Output in high Z state | 1 | ||
| Duty Cycle | DC | 45 | 55 | % | All Vdd levels | 1 | |
| Rise/Fall Time | Tr, Tf | 1.5 | 3 | ns | Vdd = 2.25V - 3.63V, 20% - 80% | 1 | |
| Output High Voltage | VOH | 90 | % Vdd | IOH = -4 mA (Vdd = 3.0V or 3.3V) | 1 | ||
| Output Low Voltage | VOL | 10 | % Vdd | IOL = 4 mA (Vdd = 3.0V or 3.3V) | 1 | ||
| Input High Voltage | VIH | 70 | % Vdd | Pin 1, OE or ST | 2 | ||
| Input Low Voltage | VIL | 30 | % Vdd | Pin 1, OE or ST | 2 | ||
| Startup Time | T_start | 5.5 | ms | Measured from the time Vdd reaches its rated minimum value | 2 | ||
| Enable/Disable Time | T_oe | 130 | ns | f = 110 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles | 2 | ||
| RMS Period Jitter | T_jitt | 1.6 | 2.5 | ps | f = 75 MHz, 2.25V to 3.63V | 2 | |
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Supply Voltage (absolute) | Vdd | -0.5 | 4 | V | 3 | ||
| Electrostatic Discharge | 2000 | V | 3 | ||||
| Soldering Temperature | 260 | °C | Follow standard Pb free soldering guidelines | 3 | |||
| Junction Temperature | 150 | °C | Exceeding this temperature for extended period may damage the device | 3 | |||
| Thermal Resistance Junction-to-Ambient, 4 Layer Board (2016 package) | θJA | 152 | °C/W | 4 layer board, 2.0 x 1.6 mm package | 3 | ||
| Thermal Resistance Junction-to-Ambient, 2 Layer Board (2016 package) | θJA | 252 | °C/W | 2 layer board, 2.0 x 1.6 mm package | 3 | ||
| Thermal Resistance Junction-to-Case, Bottom (2016 package) | θJC | 36 | °C/W | Bottom, 2.0 x 1.6 mm package | 3 | ||
| Maximum Operating Junction Temperature | 135 | °C | Max operating ambient temperature 125°C | 3 |
CAD (KiCad official)
- Symbol:
SIT8924BM-71-33E-50.000000G - Footprint:
Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm - 3D model: SMD2016-4P (KiCad packages3D, STEP)
- 3D model files:
sit8924bm-71-33e-50-000000g-etched.step/sit8924bm-71-33e-50-000000g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sit8924bm-71-33e-50-000000g.step/sit8924bm-71-33e-50-000000g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SiTime datasheet (19 pp, sha256
a88fca16392fff17, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).