main
Ray
Publish 0.1.0
d84d7f2
SIT488EESA
SIT · RS-485 / RS-422 ICs · SO-8
SIT488EESA from SIT, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Supply pin, which must be operated between 4.5 V and 5.5 V (VCC = 5 V ±10%). |
| 2 | RO | output | Receiver output that goes high when A-B ≥ -50 mV and low when A-B ≤ -200 mV, with the fail-safe threshold giving a logic-high output for open or shorted inputs. |
| 3 | DI | input | Driver input where a low level drives Y low and Z high, a high level drives Y high and Z low, with VIH minimum 2.0 V and VIL maximum 0.8 V. |
| 4 | GND | power_in | Ground pin, which is the reference point for all voltages in the datasheet. |
| 5 | Y | output | Non-inverting driver output, which is high-impedance when the driver is disabled or in shutdown. |
| 6 | Z | output | Inverting driver output, which is high-impedance when the driver is disabled or in shutdown. |
| 7 | B | input | Inverting receiver input on the bus, specified for common-mode range -7 V to 12 V, with absolute bus-pin input voltage of -8 V to 13 V. |
| 8 | A | input | Non-inverting receiver input on the bus, specified for common-mode range -7 V to 12 V, with absolute bus-pin input voltage of -8 V to 13 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SIT |
| Package | SO-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 | VCC | 7 | V | 2 | |||
| 控制端口电压 | DI | -0.3 | V | 2 | |||
| 总线侧输入电压 | A、B | -8 | 13 | V | 2 | ||
| 接收器输出电压 | RO | -0.3 | V | 2 | |||
| 工作温度范围 | -40 | 85 | ℃ | 2 | |||
| 存储工作温度范围 | -60 | 150 | ℃ | 2 | |||
| 焊接温度范围 | 300 | ℃ | 2 | ||||
| 连续功耗 | 400 | mW | SOP8 package | 2 | |||
| 电源电压(引脚定义) | VCC | 4.5 | 5.5 | V | 2 | ||
| 驱动差分输出(无负载) | VOD1 | 5 | V | 无负载 | 3 | ||
| 驱动差分输出 | VOD2 | 1.5 | V | 图 2,RL = 27 Ω | 3 | ||
| 驱动差分输出 | VOD2 | 2 | V | 图 2,RL = 50 Ω | 3 | ||
| 输出电压幅值的变化 | ∆VOD | 0.2 | V | 图 2,RL = 27 Ω | 3 | ||
| 输出共模电压 | VOC | 3 | V | 图 2,RL = 27 Ω | 3 | ||
| 共模输出电压幅值的变化 | ∆VOC | 0.2 | V | 图 2,RL = 27 Ω | 3 | ||
| 高电平输入 | VIH | 2 | V | DI | 3 | ||
| 低电平输入 | VIL | 0.8 | V | DI | 3 | ||
| 逻辑输入电流 | IIN1 | -2 | 2 | uA | DI | 3 | |
| 输出短路时的电流,短路到高 | IOSD1 | 35 | 250 | mA | 短路到 0V~12V | 3 | |
| 输出短路时的电流,短路到低 | IOSD2 | -250 | -35 | mA | 短路到-7V~0V | 3 | |
| 输入电流(A,B) | IIN2 | 125 | uA | VCC=0 或 5V, VIN = 12 V | 3 | ||
| 输入电流(A,B) | IIN2 | -100 | uA | VCC=0 或 5V, VIN = -7 V | 3 | ||
| 正向输入阈值电压 | VIT+ | -50 | mV | -7V≦VCM≦12V | 3 | ||
| 反向输入阈值电压 | VIT- | -200 | mV | -7V≦VCM≦12V | 3 | ||
| 输入迟滞电压 | Vhys | 10 | 30 | mV | -7V≦VCM≦12V | 3 | |
| 低电平输出电压 | VOL | 0.4 | V | IOUT = +4mA, VID = -200 mV | 4 | ||
| 三态输入漏电流 | IOZR | -1 | 1 | uA | 0.4 V < VO < 2.4 V | 4 | |
| 接收端输入电阻 | RIN | 96 | kΩ | -7V≦VCM≦12V | 4 | ||
| 接收器短路电流 | IOSR | -95 | 95 | mA | 0 V≤VO≤VCC | 4 | |
| 供电电流 | ICC | 250 | 400 | uA | DI=0 or VCC | 4 | |
| HBM ESD(A、B、Y、Z) | -16 | 16 | KV | 人体模型(HBM) | 4 | ||
| HBM ESD(其它端口) | -6 | 6 | KV | 人体模型(HBM) | 4 | ||
| 驱动器输入到输出传播延迟(低到高) | tDPLH | 8 | 35 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 | |
| 驱动器输入到输出传播延迟(高到低) | tDPHL | 8 | 35 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 | |
| 驱动器传播延迟偏差 | tSKEW1 | 3 | 10 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 | |
| 上升沿时间/下降沿时间 | tDR, tDF | 10 | 25 | ns | 5 | ||
| 接收器输入到输出传播延迟从低到高 | tRPLH | 20 | 80 | 150 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
| 接收器输入到输出传播延迟从高到低 | tRPHL | 20 | 80 | 150 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
| 接收器传播延迟偏差 | tSKEW2 | 7 | 10 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
CAD (KiCad official)
- Symbol:
SIT488EESA - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
sit488eesa-etched.step/sit488eesa-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sit488eesa.step/sit488eesa.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SIT datasheet (9 pp, sha256
dfd5b1bde8f60e77, retrieved 2026-10-19, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SIT488EESA
**SIT** · RS-485 / RS-422 ICs · SO-8
SIT488EESA from SIT, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC | power_in | Supply pin, which must be operated between 4.5 V and 5.5 V (VCC = 5 V ±10%). |
| 2 | RO | output | Receiver output that goes high when A-B ≥ -50 mV and low when A-B ≤ -200 mV, with the fail-safe threshold giving a logic-high output for open or shorted inputs. |
| 3 | DI | input | Driver input where a low level drives Y low and Z high, a high level drives Y high and Z low, with VIH minimum 2.0 V and VIL maximum 0.8 V. |
| 4 | GND | power_in | Ground pin, which is the reference point for all voltages in the datasheet. |
| 5 | Y | output | Non-inverting driver output, which is high-impedance when the driver is disabled or in shutdown. |
| 6 | Z | output | Inverting driver output, which is high-impedance when the driver is disabled or in shutdown. |
| 7 | B | input | Inverting receiver input on the bus, specified for common-mode range -7 V to 12 V, with absolute bus-pin input voltage of -8 V to 13 V. |
| 8 | A | input | Non-inverting receiver input on the bus, specified for common-mode range -7 V to 12 V, with absolute bus-pin input voltage of -8 V to 13 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SIT |
| Package | SO-8 |
| Category | Interface |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 | VCC | | | 7 | V | | 2 |
| 控制端口电压 | DI | -0.3 | | | V | | 2 |
| 总线侧输入电压 | A、B | -8 | | 13 | V | | 2 |
| 接收器输出电压 | RO | -0.3 | | | V | | 2 |
| 工作温度范围 | | -40 | | 85 | ℃ | | 2 |
| 存储工作温度范围 | | -60 | | 150 | ℃ | | 2 |
| 焊接温度范围 | | | | 300 | ℃ | | 2 |
| 连续功耗 | | | | 400 | mW | SOP8 package | 2 |
| 电源电压(引脚定义) | VCC | 4.5 | | 5.5 | V | | 2 |
| 驱动差分输出(无负载) | VOD1 | | | 5 | V | 无负载 | 3 |
| 驱动差分输出 | VOD2 | 1.5 | | | V | 图 2,RL = 27 Ω | 3 |
| 驱动差分输出 | VOD2 | 2 | | | V | 图 2,RL = 50 Ω | 3 |
| 输出电压幅值的变化 | ∆VOD | | | 0.2 | V | 图 2,RL = 27 Ω | 3 |
| 输出共模电压 | VOC | | | 3 | V | 图 2,RL = 27 Ω | 3 |
| 共模输出电压幅值的变化 | ∆VOC | | | 0.2 | V | 图 2,RL = 27 Ω | 3 |
| 高电平输入 | VIH | 2 | | | V | DI | 3 |
| 低电平输入 | VIL | | | 0.8 | V | DI | 3 |
| 逻辑输入电流 | IIN1 | -2 | | 2 | uA | DI | 3 |
| 输出短路时的电流,短路到高 | IOSD1 | 35 | | 250 | mA | 短路到 0V~12V | 3 |
| 输出短路时的电流,短路到低 | IOSD2 | -250 | | -35 | mA | 短路到-7V~0V | 3 |
| 输入电流(A,B) | IIN2 | | | 125 | uA | VCC=0 或 5V, VIN = 12 V | 3 |
| 输入电流(A,B) | IIN2 | -100 | | | uA | VCC=0 或 5V, VIN = -7 V | 3 |
| 正向输入阈值电压 | VIT+ | | | -50 | mV | -7V≦VCM≦12V | 3 |
| 反向输入阈值电压 | VIT- | -200 | | | mV | -7V≦VCM≦12V | 3 |
| 输入迟滞电压 | Vhys | | 10 | 30 | mV | -7V≦VCM≦12V | 3 |
| 低电平输出电压 | VOL | | | 0.4 | V | IOUT = +4mA, VID = -200 mV | 4 |
| 三态输入漏电流 | IOZR | -1 | | 1 | uA | 0.4 V < VO < 2.4 V | 4 |
| 接收端输入电阻 | RIN | 96 | | | kΩ | -7V≦VCM≦12V | 4 |
| 接收器短路电流 | IOSR | -95 | | 95 | mA | 0 V≤VO≤VCC | 4 |
| 供电电流 | ICC | | 250 | 400 | uA | DI=0 or VCC | 4 |
| HBM ESD(A、B、Y、Z) | | -16 | | 16 | KV | 人体模型(HBM) | 4 |
| HBM ESD(其它端口) | | -6 | | 6 | KV | 人体模型(HBM) | 4 |
| 驱动器输入到输出传播延迟(低到高) | tDPLH | 8 | | 35 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 |
| 驱动器输入到输出传播延迟(高到低) | tDPHL | 8 | | 35 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 |
| 驱动器传播延迟偏差 | tSKEW1 | | 3 | 10 | ns | RDIFF = 54 Ω, CL1=CL2=100pF (见图 3 与图 4) | 4 |
| 上升沿时间/下降沿时间 | tDR, tDF | 10 | | 25 | ns | | 5 |
| 接收器输入到输出传播延迟从低到高 | tRPLH | 20 | 80 | 150 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
| 接收器输入到输出传播延迟从高到低 | tRPHL | 20 | 80 | 150 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
| 接收器传播延迟偏差 | tSKEW2 | | 7 | 10 | ns | 见图 5 与图 6,VID≥2.0V;上升与下降沿时间 VID≤15ns | 5 |
## CAD (KiCad official)
- Symbol: `SIT488EESA`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `sit488eesa-etched.step` / `sit488eesa-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sit488eesa.step` / `sit488eesa.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [SIT datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588903914473197568) (9 pp, sha256 `dfd5b1bde8f60e77`, retrieved 2026-10-19, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sit488eesa-datasheet.pdf)