Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SiT1602BI-21-33E-26.000000

SiTime · Pre-programmed Oscillators · SMD3225-4P

SiT1602BI-21-33E-26.000000 from SiTime, in a SMD3225-4P. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 OE/ST/NC input In OE mode, logic H gives the specified frequency output and logic L puts the output in high impedance, disabling only the output driver; a pull-up of 10 kΩ or less is recommended if the pin is not externally driven.
2 GND power_in Electrical ground, and a capacitor of 0.1 µF or higher between VDD and GND is required.
3 OUT output Oscillator clock output, with LVCMOS/HCMOS-compatible levels and a 90% VDD minimum VOH and 10% VDD maximum VOL.
4 VDD power_in Power supply voltage for this MPN's 3.3 V option (3.3 V ±10%, 2.97 V to 3.63 V per the Electrical Characteristics), with a 0.1 µF or higher capacitor required between VDD and GND.

Key specifications

Parameter Value
Manufacturer SiTime
Package SMD3225-4P
Category Crystal Oscillator/Oscillator/Resonator
Pins 4

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Frequency Stability F_stab -20 20 ppm Inclusive of initial tolerance at 25°C, 1st year aging at 25°C, and variations over operating temperature, rated power supply voltage and load. 1
Operating Temperature Range (Industrial) T_use -40 85 °C Industrial 1
Supply Voltage (3.3 V ±10%) Vdd 2.97 3.3 3.63 V 1
Current Consumption Idd 3.8 4.5 mA No load condition, f = 20 MHz, Vdd = 2.8V to 3.3V 1
OE Disable Current I_OD 4.2 mA Vdd = 2.5V to 3.3V, OE = GND, Output in high-Z state 1
Duty Cycle DC 45 55 % All Vdds. See Duty Cycle definition in Figure 3 and Footnote 6 1
Rise/Fall Time (20%-80%) Tr, Tf 1 2 ns Vdd = 2.5V, 2.8V, 3.0V or 3.3V, 20% - 80% 1
Rise/Fall Time (20%-80%), wide supply Tr, Tf 2 ns Vdd = 2.25V - 3.63V, 20% - 80% 1
Output High Voltage VOH 90 % Vdd IOH = -4 mA (Vdd = 3.0V or 3.3V) 1
Output Low Voltage VOL 10 % Vdd IOL = 4 mA (Vdd = 3.0V or 3.3V) 1
Input High Voltage VIH 70 % Vdd Pin 1, OE or ST 2
Input Low Voltage VIL 30 % Vdd Pin 1, OE or ST 2
Input Pull-up Impedance Z_in 50 87 150 k Pin 1, OE logic high or logic low, or ST logic high 2
Startup Time T_start 5 ms Measured from the time Vdd reaches its rated minimum value 2
Enable/Disable Time T_oe 138 ns f = 77.76 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles 2
RMS Period Jitter T_jitt 1.8 3 ps f = 75 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V 2
Peak-to-peak Period Jitter T_pk 12 25 ps f = 75 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V 2
RMS Phase Jitter (random) T_phj 0.5 0.9 ps f = 75 MHz, Integration bandwidth = 900 kHz to 7.5 MHz 2
RMS Phase Jitter (random) T_phj 1.3 2 ps f = 75 MHz, Integration bandwidth = 12 kHz to 20 MHz 2
Storage Temperature -65 150 °C 3
Supply Voltage (absolute) Vdd -0.5 4 V 3
Electrostatic Discharge 2000 V 3
Soldering Temperature 260 °C Follow standard Pb free soldering guidelines 3
Junction Temperature 150 °C Exceeding this temperature for extended period of time may damage the device 3
Thermal Resistance Junction-to-Ambient (3225) θJA 109 °C/W 4 Layer Board, JESD51 reference layout 3
Thermal Resistance Junction-to-Ambient (3225) θJA 212 °C/W 2 Layer Board, JESD51 reference layout 3
Thermal Resistance Junction-to-Case Bottom (3225) θJC 27 °C/W Bottom, JESD51 reference layout 3
Maximum Operating Junction Temperature 95 °C Max operating ambient temperature 85°C 3

CAD (KiCad official)

  • Symbol: SiT1602BI-21-33E-26.000000
  • Footprint: Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm
  • 3D model: SMD3225-4P (KiCad packages3D, STEP)
  • 3D model files: sit1602bi-21-33e-26-000000-etched.step / sit1602bi-21-33e-26-000000-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); sit1602bi-21-33e-26-000000.step / sit1602bi-21-33e-26-000000.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SiTime datasheet (17 pp, sha256 d829a6872da0ca5a, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF