Generated by kicad-footprint-generator · KiCad file format 20260206
SI5356A-B-GMR
SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-24-EP(4x4)
SI5356A-B-GMR from SILICON LABS, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | XA | input | Crystal connection for a 25 or 27 MHz crystal connected across XA and XB; tie to GND if no input clock is used. |
| 2 | XB | input | Crystal connection for a 25 or 27 MHz crystal connected across XA and XB; tie to GND if no input clock is used. |
| 3 | I2C_LSB | input | Least significant bit of the I2C address, 3.3 V tolerant, allowing up to two Si5356 devices on the same I2C bus. |
| 4 | CLKIN | input | Single-ended high-impedance CMOS clock input that must be dc coupled; tie to GND if a crystal is the reference. |
| 5 | SSC_DIS | input | Spread spectrum disable; the maximum voltage must not exceed 1.3 V, a voltage of 0.85 to 1.3 V disables spread spectrum and GND enables it. |
| 6 | OEB | input | Active-low output enable; the maximum voltage must not exceed 1.3 V, a voltage of 0.85 to 1.3 V disables all outputs and GND enables all outputs. |
| 7 | VDD | power_in | Core supply voltage of 1.8, 2.5, or 3.3 V; a 0.1 μF bypass capacitor should be located very close to this pin. |
| 8 | INTR | output | Open-drain maskable interrupt output (0 = no interrupt, 1 = interrupt present) that requires an external pullup of more than 1 k, typically 1-4 k. |
| 9 | CLK7 | output | CMOS output clock 7; must be left floating if unused. |
| 10 | CLK6 | output | CMOS output clock 6; must be left floating if unused. |
| 11 | VDDOD | power_in | Clock output bank D supply for CLK6 and CLK7, operable from 1.8, 2.5, or 3.3 V; if unused it must be tied to pin 7 and/or pin 24 or a rail above 1.5 V. |
| 12 | SCL | input | I2C serial clock input, 3.3 V tolerant. |
| 13 | CLK5 | output | CMOS output clock 5; must be left floating if unused. |
| 14 | CLK4 | output | CMOS output clock 4; must be left floating if unused. |
| 15 | VDDOC | power_in | Clock output bank C supply for CLK4 and CLK5, operable from 1.8, 2.5, or 3.3 V; if unused it must be tied to pin 7 and/or pin 24 or a rail above 1.5 V. |
| 16 | VDDOB | power_in | Clock output bank B supply for CLK2 and CLK3, operable from 1.8, 2.5, or 3.3 V; if unused it must be tied to pin 7 and/or pin 24 or a rail above 1.5 V. |
| 17 | CLK3 | output | CMOS output clock 3; must be left floating if unused. |
| 18 | CLK2 | output | CMOS output clock 2; must be left floating if unused. |
| 19 | SDA | bidirectional | I2C serial data input/output, 3.3 V tolerant. |
| 20 | VDDOA | power_in | Clock output bank A supply for CLK0 and CLK1, operable from 1.8, 2.5, or 3.3 V; if unused it must be tied to pin 7 and/or pin 24 or a rail above 1.5 V. |
| 21 | CLK1 | output | CMOS output clock 1; must be left floating if unused. |
| 22 | CLK0 | output | CMOS output clock 0; must be left floating if unused. |
| 23 | GND | power_in | Ground that must be connected to system ground, with minimized ground path impedance for optimal performance. |
| 24 | VDD | power_in | Core supply voltage of 1.8, 2.5, or 3.3 V; a 0.1 μF bypass capacitor should be located very close to this pin. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-24-EP(4x4) |
| Category | RTC/Clock Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core Supply Voltage | VDD | 2.97 | 3.3 | 3.63 | V | 4 | |
| Core Supply Voltage | VDD | 2.25 | 2.5 | 2.75 | V | 4 | |
| Core Supply Voltage | VDD | 1.71 | 1.8 | 1.98 | V | 4 | |
| Output Buffer Supply Voltage | VDDO | 1.71 | 3.63 | V | 4 | ||
| Ambient Temperature | TA | -40 | 85 | oC | 4 | ||
| Core Supply Current | IDD | 45 | 60 | mA | 100 MHz on all outputs, 25 MHz refclk | 4 | |
| Output Buffer Supply Current | IDDOx | 6 | 9 | mA | CMOS, 50 MHz 15 pF load | 4 | |
| Output Buffer Supply Current | IDDOx | 13 | 18 | mA | CMOS, 200 MHz 3.3 V VDD0 | 4 | |
| Output Buffer Supply Current | IDDOx | 10 | 14 | mA | CMOS, 200 MHz 2.5 V | 4 | |
| Output Buffer Supply Current | IDDOx | 7 | 10 | mA | CMOS, 200 MHz 1.8 V | 4 | |
| High Level Input Voltage | VIH | 3.63 | V | CLKIN, I2C_LSB | 4 | ||
| High Level Input Voltage | VIH | 0.85 | 1.3 | V | SSC_DIS, OEB | 4 | |
| Low Level Input Voltage | VIL | -0.2 | V | CLKIN, I2C_LSB | 4 | ||
| Low Level Input Voltage | VIL | 0.3 | V | SSC_DIS, OEB | 4 | ||
| Clock Output Low Level Output Voltage | VOL | 0.3 | V | Pins: CLK0-7 IOL = +4 mA | 4 | ||
| INTR Low Level Output Voltage | VOLINTR | 0 | 0.4 | V | Pin: INTR IOL = +3 mA | 4 | |
| Clock Input Frequency | FIN | 5 | 200 | MHz | 5 | ||
| Clock Input Rise/Fall Time 20-80% VDD | TR/TF | 2.3 | ns | 20-80% VDD | 5 | ||
| Clock Input Rise/Fall Time 10-90% VDD | TR/TF | 4 | ns | 10-90% VDD | 5 | ||
| Clock Input Duty Cycle | DC | 40 | 60 | % | Input tr/tf within specified limits shown above | 5 | |
| Clock Input Capacitance | CIN | 2 | pF | 5 | |||
| Clock Output Frequency | FO | 1 | 200 | MHz | 5 | ||
| Clock Output Frequency Synthesis Resolution | FRES | 0 | 0 | 1 | ppb | See "3.4. Frequency Configuration" on page 11 | 5 |
| Output Load Capacitance | CL | 15 | pF | 5 | |||
| Clock Output Rise/Fall Time 20 to 80% | TR/TF | 2 | ns | 20 to 80% VDD, CL = 15 pF | 5 | ||
| Clock Output Rise/Fall Time 20 to 80% | TR/TF | 0.45 | 0.85 | ns | 20 to 80% VDD, CL = 2 pF | 5 | |
| Clock Output Duty Cycle | DC | 45 | 50 | 55 | % | Measured at VDD/2 | 5 |
| Powerup Time | TPU | 2 | ms | POR to output clock valid | 5 | ||
| Output Enable Time | TOE | 10 | µs | 5 | |||
| Output-Output Skew | TSKEW | -150 | 150 | ps | Outputs at same frequency, fOUT > 5 MHz | 5 | |
| Period Jitter | JPPKPK | 50 | 75 | ps pk-pk | 10000 cycles | 5 | |
| Cycle-Cycle Jitter | JCCPK | 40 | 70 | ps pk | 10000 cycles | 5 | |
| Phase Jitter | JPH | 2 | ps rms | 12 kHz to 20 MHz | 5 | ||
| PLL Loop Bandwidth | FBW | 1.6 | MHz | 5 | |||
| CLKIN Loss of Signal Assert Time | tLOS | 2.6 | 5 | µs | 5 | ||
| CLKIN Loss of Signal Deassert Time | tLOS_b | 0.01 | 0.2 | 1 | µs | 5 | |
| Crystal Frequency Option 1 | FXTAL | 25 | MHz | Option 1 | 6 | ||
| Load Capacitance (on-chip differential) supported | cL | 11 | 12 | 13 | pF | supported | 6 |
| Load Capacitance (on-chip differential) recommended | cL | 17 | 18 | 19 | pF | recommended | 6 |
| Crystal Output Capacitance | CO | 5 | pF | 6 | |||
| Equivalent Series Resistance | ESR | 100 | 25 MHz | 6 | |||
| Equivalent Series Resistance | ESR | 75 | 27 MHz | 6 | |||
| Crystal Drive Level Rating | dL | 100 | µW | 6 | |||
| Crystal Frequency Option 2 | FXTAL | 27 | MHz | Option 2 | 6 | ||
| HIGH level input voltage (SCL, SDA) | VIHI2C | 3.63 | V | 6 | |||
| LOW level output voltage (open drain or open collector) | VOLI2C | 0.4 | V | at 3 mA sink current, VDDI2C = 2.5/3.3 V | 6 | ||
| Capacitance for each I/O pin | CII2C | 4 | pF | VIN = -0.1 to VDDI2C | 6 | ||
| I2C Bus timeout | 25 | 35 | ms | 6 | |||
| Thermal Resistance Junction to Ambient | JA | 37 | °C/W | Still Air | 7 | ||
| Thermal Resistance Junction to Case | JC | 25 | °C/W | Still Air | 7 | ||
| Supply Voltage Range | VDD | -0.5 | 3.8 | V | 7 | ||
| Input Voltage Range (all pins except pins 1,2,5,6) | VI | -0.5 | 3.8 | V | all pins except pins 1,2,5,6 | 7 | |
| Input Voltage Range (pins 1,2,5,6) | VI2 | -0.5 | 1.3 | V | pins 1,2,5,6 | 7 | |
| Output Voltage Range | VO | -0.5 | V | 7 | |||
| Junction Temperature | TJ | -55 | 150 | oC | 7 | ||
| ESD Tolerance HBM | HBM | 2.5 | kV | 7 | |||
| ESD Tolerance CDM | CDM | 550 | V | 7 | |||
| Soldering Temperature (Pb-free profile) | TPEAK | 260 | oC | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. | 24 | |
| contacts | gold | 6. Terminal base alloy: Cu. 7. Terminal plating/grid array material: Au/NiPd. | 24 |
CAD (KiCad official)
- Symbol:
SI5356A-B-GMR - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
si5356a-b-gmr-etched.step/si5356a-b-gmr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5356a-b-gmr.step/si5356a-b-gmr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (29 pp, sha256
bee4c0799e3a36b8, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).