Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

SI5335A-B07338-GM

SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-24-EP(4x4)

SI5335A-B07338-GM from SILICON LABS, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 XA/CLKIN input Main differential or single-ended clock input or XTAL input; must be ac-coupled, and single-ended input swing must be limited to 1.2 Vpp.
2 XB/CLKINB input Main differential or single-ended clock input or XTAL input; must be ac-coupled, and single-ended input swing must be limited to 1.2 Vpp.
3 P3 input 3.3 V tolerant multi-function input whose function (OEB_all, OEB0-3, SSENB or RESET) is selected at configuration with ClockBuilder.
4 GND power_in Ground; must be connected to system ground for proper device operation.
5 P5 input Multi-function input (OEB_all, OEB0-3 or SSENB) that needs a resistor divider when driven by a signal greater than 1.2 V.
6 P6 input Multi-function input (OEB_all, OEB0-3 or SSENB) that needs a resistor divider when driven by a signal greater than 1.2 V.
7 VDD power_in Core supply voltage of 1.8, 2.5 or 3.3 V, with a 0.1 µF bypass capacitor very close to the pin.
8 LOS output Open-drain loss-of-signal output (high = input clock absent or PLL not locked) that uses a typical 1-4 kΩ pullup to a supply as high as 3.6 V.
9 CLK3B output Output clock B for channel 3, single-ended or the other half of a differential pair with CLK3A; leave floating if unused.
10 CLK3A output Output clock A for channel 3, single-ended or the other half of a differential pair with CLK3B; leave floating if unused.
11 VDDO3 power_in Output supply (3.3, 2.5, 1.8 or 1.5 V) for CLK3A,B with a 0.1 µF capacitor very close; tie to VDD if CLK3 is unused.
12 P1 input 3.3 V tolerant multi-function input whose function (OEB_all, OEB0-3, SSENB, FS0, FS1 or RESET) is selected at configuration with ClockBuilder.
13 CLK2B output Output clock B for channel 2, single-ended or the other half of a differential pair with CLK2A; leave floating if unused.
14 CLK2A output Output clock A for channel 2, single-ended or the other half of a differential pair with CLK2B; leave floating if unused.
15 VDDO2 power_in Output supply (3.3, 2.5, 1.8 or 1.5 V) for CLK2A,B with a 0.1 µF capacitor very close; tie to VDD if CLK2 is unused.
16 VDDO1 power_in Output supply (3.3, 2.5, 1.8 or 1.5 V) for CLK1A,B with a 0.1 µF capacitor very close; tie to VDD if CLK1 is unused.
17 CLK1B output Output clock B for channel 1, single-ended or the other half of a differential pair with CLK1A; leave floating if unused.
18 CLK1A output Output clock A for channel 1, single-ended or the other half of a differential pair with CLK1B; leave floating if unused.
19 P2 input 3.3 V tolerant multi-function input whose function (OEB_all, OEB0-3, SSENB, FS1 or RESET) is selected at configuration with ClockBuilder.
20 VDDO0 power_in Output supply (3.3, 2.5, 1.8 or 1.5 V) for CLK0A,B with a 0.1 µF capacitor very close; tie to VDD if CLK0 is unused.
21 CLK0B output Output clock B for channel 0, single-ended or the other half of a differential pair with CLK0A; leave floating if unused.
22 CLK0A output Output clock A for channel 0, single-ended or the other half of a differential pair with CLK0B; leave floating if unused.
23 RSVD_GND power_in Ground; must be connected to system ground, minimizing ground path impedance.
24 VDD power_in Core supply voltage of 1.8, 2.5 or 3.3 V, with a 0.1 µF bypass capacitor very close to the pin.
25 GND_PAD power_in Center ground pad; the device will not function unless it is connected to a PCB ground plane with at least five vias.

Key specifications

Parameter Value
Manufacturer SILICON LABS
Package QFN-24-EP(4x4)
Category Clock and Timing
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient Temperature TA -40 25 85 °C 4
Core Supply Voltage VDD 2.97 3.3 3.63 V VDD = 3.3 V ±10% 4
Core Supply Voltage VDD 2.25 2.5 2.75 V VDD = 2.5 V ±10% 4
Core Supply Voltage VDD 1.71 1.8 1.98 V VDD = 1.8 V -5% to +10% 4
Output Buffer Supply Voltage VDDOn 1.4 3.63 V 4
Core Supply Current (Clock Generator Mode) IDDCG 45 60 mA 100 MHz on all outputs, 25 MHz refclk, clock generator mode 4
Output Buffer Supply Current IDDOx 30 mA LVPECL, 350 MHz 4
Output Buffer Supply Current IDDOx 8 mA LVDS, 350 MHz 4
Output Buffer Supply Current IDDOx 20 mA HCSL, 250 MHz, 2 pF load 4
Output Buffer Supply Current IDDOx 19 mA SSTL, 350 MHz 4
Output Buffer Supply Current IDDOx 6 9 mA CMOS, 50 MHz, 15 pF load; single CMOS driver active 4
Output Buffer Supply Current IDDOx 13 18 mA CMOS, 200 MHz, 3.3 V VDD0; single CMOS driver active 4
PLL Acquisition Time tACQ 25 ms 1.6 MHz loop bandwidth 5
PLL Tracking Range fTRACK 5000 20000 ppm 475 kHz or 1.6 MHz loop bandwidth 5
MultiSynth Frequency Synthesis Resolution fRES 0 0 1 ppb Output frequency < Fvco/8 5
CLKIN Loss of Signal Detect Time tLOS 2.6 5 µs 5
CLKIN Loss of Signal Release Time tLOSRLS 0.01 0.2 1 µs 5
POR to Output Clock Valid tRDY 2 ms 5
Input-to-Output Propagation Delay tPROP 2.5 4 ns Buffer Mode (PLL Bypass) 5
Reset Minimum Pulse Width tRESET 200 ns 5
Output-Output Skew tDSKEW 100 ps FOUT > 5 MHz 5
Spread Spectrum PP Frequency Deviation SSDEV -0.45 -0.5 % FOUT = 100 MHz 5
Spread Spectrum Modulation Rate SSDEV 30 31.5 33 kHz FOUT = 100 MHz 5
Output Clock Frequency (differential) fOUT 1 350 MHz LVPECL, LVDS, CML 7
Output Clock Frequency (differential) fOUT 1 250 MHz HCSL 7
LVPECL Peak-to-Peak Single-Ended Swing VSEPP 0.55 0.8 0.96 VPP LVPECL 7
LVDS Output Common Mode Voltage VOC 1.125 1.2 1.275 V LVDS, 2.5/3.3 V 7
LVDS Peak-to-Peak Single-Ended Swing VSEPP 0.25 0.35 0.45 VPP LVDS, 2.5/3.3 V 7
LVDS Output Common Mode Voltage VOC 0.8 0.875 0.95 V LVDS, 1.8 V 7
HCSL Output Common Mode Voltage VOC 0.35 0.375 0.4 V HCSL 7
HCSL Peak-to-Peak Single-Ended Swing VSEPP 0.575 0.725 0.85 VPP HCSL 7
CML Peak-to-Peak Single-Ended Swing VSEPP 0.67 0.86 1.07 VPP CML 7
Output Rise/Fall Time (20% to 80%) tR/tF 450 ps LVPECL, LVDS, HCSL, CML 7
Output Duty Cycle (differential) DC 45 55 % LVPECL, LVDS, HCSL, CML 8
Output Clock Frequency (single-ended) fOUT 1 200 MHz CMOS 8
Output Clock Frequency (single-ended) fOUT 1 350 MHz SSTL, HSTL 8
CMOS Output Rise/Fall Time (20% to 80%) tR/tF 0.45 0.85 ns 2 pF load 8
CMOS Output Rise/Fall Time (20% to 80%) tR/tF 2 ns 15 pF load 8
CMOS Output Voltage Low VOL 0.3 V 4 mA load 8
Output Duty Cycle (single-ended) DC 45 55 % 8
Input Voltage Low VIL -0.1 V Pins P1, P2, P3 9
Input Voltage Low VIL 0.3 V Pins P5 and P6 9
Input Voltage High VIH 3.73 V Pins P1, P2, P3 9
Input Voltage High VIH 0.85 1.2 V Pins P5 and P6 9
Output Voltage Low (LOS) VOL 0 0.4 V ISINK = 3 mA 9
Crystal Output Capacitance (25 MHz) cO 5 pF 25 MHz crystal 9
Crystal Equivalent Series Resistance (25 MHz) rESR 100 Ω 25 MHz crystal 9
Crystal Max Drive Level (25 MHz) dL 100 µW 25 MHz crystal 9
Crystal Output Capacitance (27 MHz) cO 5 pF 27 MHz crystal 9
Crystal Equivalent Series Resistance (27 MHz) rESR 75 Ω 27 MHz crystal 9
Crystal Max Drive Level (27 MHz) dL 100 µW 27 MHz crystal 9
DC Supply Voltage VDD -0.5 3.8 V 15
Input Voltage VIN -0.5 1.3 V Pins XA/CLKIN, XB/CLKINB, P5, P6 15
Input Voltage VIN -0.5 3.8 V Pins P1, P2, P3 15
Storage Temperature Range TSTG -55 150 °C 15
Junction Temperature TJ 150 °C 15
Thermal Resistance Junction to Ambient JA 37 °C/W Still Air 14
Thermal Resistance Junction to Case JC 25 °C/W Still Air 14

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
housing abs 10. Gen 4 specifications based on the PCI-Express Base Specification 4.0 rev. 0.5. 11. Download the Silicon Labs PCIe Clock Jitter Tool at www.silabs.com/pcie-learningcenter. 10
contacts gold 5. Terminal base alloy: Cu 6. Terminal plating/grid array material: Au/NiPd. 42

CAD (KiCad official)

  • Symbol: SI5335A-B07338-GM
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: si5335a-b07338-gm-etched.step / si5335a-b07338-gm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si5335a-b07338-gm.step / si5335a-b07338-gm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SILICON LABS datasheet (47 pp, sha256 e332299219a557cb, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF