Generated by kicad-footprint-generator · KiCad file format 20260206
SI5326C-C-GMR
SILICON LABS · Clock Generators / Frequency Synthesizers / PLL · QFN-36-EP(6x6)
SI5326C-C-GMR from SILICON LABS, in a QFN-36-EP(6x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RST | input | Active-low external hardware reset that resets internal logic and forces registers to default values, with clock outputs tristated during reset and a weak pull-up on the pin. |
| 2 | NC | unconnected | No connection; leave floating and make no external connections to this pin for normal operation. |
| 3 | INT_C1B | output | Device interrupt output or CKIN1 invalid (LOS/FOS) alarm output with polarity set by INT_POL or CK_BAD_POL, and tristates if no function is selected. |
| 4 | C2B | output | CKIN2 invalid (LOS, optionally FOS) alarm output that is active when CK2_BAD_PIN = 1 and tristates when CK2_BAD_PIN = 0. |
| 5 | VDD | power_in | Supply pin for 1.8 V, 2.5 V, or 3.3 V operation, to be bypassed with a 0.1 µF capacitor, with a 1.0 µF capacitor also placed as close to the device as practical. |
| 6 | XA | input | Analog connection for an external crystal or high-quality reference clock (TCXO or OCXO), with frequency set by the RATE[1:0] pins. |
| 7 | XB | input | Analog connection for the second terminal of an external crystal or high-quality reference clock (TCXO or OCXO), with frequency set by the RATE[1:0] pins. |
| 8 | GND | power_in | Ground that must be connected to system ground with minimized path impedance, and does not remove the need to ground the GND pad on the package bottom. |
| 9 | NC | unconnected | No connection; leave floating and make no external connections to this pin for normal operation. |
| 10 | VDD | power_in | Supply pin for 1.8 V, 2.5 V, or 3.3 V operation, to be bypassed with a 0.1 µF capacitor. |
| 11 | RATE0 | input | Three-level input (L = ground, M = VDD/2, H = VDD) selecting the external crystal or reference type and rate, with a weak pull-up and pull-down that default it to M. |
| 12 | CKIN2+ | input | Positive differential input clock 2 accepting 2 kHz to 710 MHz, which can also be driven single-ended. |
| 13 | CKIN2- | input | Negative differential input clock 2 accepting 2 kHz to 710 MHz, which can also be driven single-ended. |
| 14 | NC | unconnected | No connection; leave floating and make no external connections to this pin for normal operation. |
| 15 | RATE1 | input | Three-level input (L = ground, M = VDD/2, H = VDD) selecting the external crystal or reference type and rate, with a weak pull-up and pull-down that default it to M. |
| 16 | CKIN1+ | input | Positive differential input clock 1 accepting 2 kHz to 710 MHz, which can also be driven single-ended. |
| 17 | CKIN1- | input | Negative differential input clock 1 accepting 2 kHz to 710 MHz, which can also be driven single-ended. |
| 18 | LOL | output | Active-high PLL loss-of-lock indicator (1 = unlocked) enabled by LOL_PIN = 1, with polarity set by LOL_POL and tristated when LOL_PIN = 0. |
| 19 | DEC | input | Skew decrement input where each pulse reduces input-to-output skew by about 200 ps (1/fOSC) when INCDEC_PIN = 1, with a weak pull-down. |
| 20 | INC | input | Skew increment input where each pulse increases input-to-output skew by about 200 ps (1/fOSC) when INCDEC_PIN = 1, with a weak pull-down. |
| 21 | CS_CA | bidirectional | Manual input clock select (0 = CKIN1, 1 = CKIN2) when CKSEL_PIN = 1, or active-clock indicator output when CK_ACTV_PIN = 1, and must be tied high or low when configured as an input. |
| 22 | SCL | input | Serial clock input for both I2C and SPI control modes, with a weak pull-down. |
| 23 | SDA_SDO | bidirectional | Bidirectional serial data port in I2C mode (CMODE = 0) and serial data output in SPI mode (CMODE = 1). |
| 24 | A0 | input | Hardware I2C address bit A0 (address 1101 A2 A1 A0) in I2C mode, ignored in SPI mode, with a weak pull-down. |
| 25 | A1 | input | Hardware I2C address bit A1 (address 1101 A2 A1 A0) in I2C mode, ignored in SPI mode, with a weak pull-down. |
| 26 | A2_SS | input | Hardware I2C address bit A2 in I2C mode or slave select input in SPI mode, with a weak pull-down. |
| 27 | SDI | input | Ignored in I2C mode and serves as the serial data input in SPI mode, with a weak pull-down. |
| 28 | CKOUT1+ | output | Positive output clock 1 with a 2 kHz to 1.4 GHz range, with format selected by SFOUT1_REG and both pins driving identical single-ended outputs in CMOS format. |
| 29 | CKOUT1- | output | Negative output clock 1 with a 2 kHz to 1.4 GHz range, with format selected by SFOUT1_REG and both pins driving identical single-ended outputs in CMOS format. |
| 30 | NC | unconnected | No connection; leave floating and make no external connections to this pin for normal operation. |
| 31 | GND | power_in | Ground that must be connected to system ground with minimized path impedance, and does not remove the need to ground the GND pad on the package bottom. |
| 32 | VDD | power_in | Supply pin for 1.8 V, 2.5 V, or 3.3 V operation, to be bypassed with a 0.1 µF capacitor. |
| 33 | NC | unconnected | No connection; leave floating and make no external connections to this pin for normal operation. |
| 34 | CKOUT2- | output | Negative output clock 2 with a 2 kHz to 1.4 GHz range, with format selected by SFOUT2_REG and both pins driving identical single-ended outputs in CMOS format. |
| 35 | CKOUT2+ | output | Positive output clock 2 with a 2 kHz to 1.4 GHz range, with format selected by SFOUT2_REG and both pins driving identical single-ended outputs in CMOS format. |
| 36 | CMODE | input | Control mode select (0 = I2C, 1 = SPI) that must not be left NC and must be tied either high or low. |
| 37 | GND PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-36-EP(6x6) |
| Category | RTC/Clock Chip |
| Pins | 37 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -40 | 25 | 85 | C | 4 | |
| Supply Voltage during Normal Operation, 3.3 V nominal | VDD | 2.97 | 3.3 | 3.63 | V | 3.3 V nominal | 4 |
| Supply Voltage during Normal Operation, 2.5 V nominal | VDD | 2.25 | 2.5 | 2.75 | V | 2.5 V nominal | 4 |
| Supply Voltage during Normal Operation, 1.8 V nominal | VDD | 1.71 | 1.8 | 1.89 | V | 1.8 V nominal | 4 |
| Supply Current, LVPECL, 622.08 MHz out, both CKOUTs enabled | IDD | 251 | 279 | mA | LVPECL format; 622.08 MHz out; both CKOUTs enabled | 5 | |
| Supply Current, LVPECL, 622.08 MHz out, 1 CKOUT enabled | IDD | 217 | 243 | mA | LVPECL format; 622.08 MHz out; 1 CKOUT enabled | 5 | |
| Supply Current, CMOS, 19.44 MHz out, both CKOUTs enabled | IDD | 204 | 234 | mA | CMOS format; 19.44 MHz out; both CKOUTs enabled | 5 | |
| Supply Current, CMOS, 19.44 MHz out, 1 CKOUT enabled | IDD | 194 | 220 | mA | CMOS format; 19.44 MHz out; 1 CKOUT enabled | 5 | |
| CKINn Input Common Mode Voltage (Input Threshold Voltage) | VICM | 0.9 | 1.4 | V | VDD 1.8 V ± 5% | 5 | |
| CKINn Input Common Mode Voltage (Input Threshold Voltage) | VICM | 1 | 1.7 | V | VDD 2.5 V ± 10% | 5 | |
| CKINn Input Common Mode Voltage (Input Threshold Voltage) | VICM | 1.1 | 1.95 | V | VDD 3.3 V ± 10% | 5 | |
| CKINn Input Resistance | CKNRIN | 20 | 40 | 60 | kΩ | Single-ended | 5 |
| CKINn Single-Ended Input Voltage Swing | VISE | 0.2 | VPP | fCKIN < 212.5 MHz; see Figure 1 | 5 | ||
| CKINn Single-Ended Input Voltage Swing | VISE | 0.25 | VPP | fCKIN > 212.5 MHz; see Figure 1 | 5 | ||
| CKINn Differential Input Voltage Swing | VID | 0.2 | VPP | fCKIN < 212.5 MHz; see Figure 1 | 5 | ||
| CKINn Differential Input Voltage Swing | VID | 0.25 | VPP | fCKIN > 212.5 MHz; see Figure 1 | 5 | ||
| Output Clock Differential Output Swing, LVPECL | CKOVD | 1.1 | 1.9 | VPP | LVPECL 100 Ω load line-to-line | 6 | |
| Output Clock Single Ended Output Swing, LVPECL | CKOVSE | 0.5 | 0.93 | VPP | LVPECL 100 Ω load line-to-line | 6 | |
| Output Clock Differential Output Voltage, CML | CKOVD | 350 | 425 | 500 | mVPP | CML 100 Ω load line-to-line | 6 |
| Output Clock Differential Output Voltage, LVDS | CKOVD | 500 | 700 | 900 | mVPP | LVDS 100 Ω load line-to-line | 6 |
| Output Clock Low Swing LVDS Differential Output Voltage | 350 | 425 | 500 | mVPP | Low swing LVDS 100 Ω load line-to-line | 6 | |
| Output Clock Common Mode Output Voltage, LVDS | CKOVCM | 1.125 | 1.2 | 1.275 | V | LVDS 100 Ω load line-to-line | 6 |
| Output Voltage Low, CMOS | CKOVOLLH | 0.4 | V | CMOS | 6 | ||
| 2-Level LVCMOS Input Voltage Low | VIL | 0.5 | V | VDD = 1.71 V | 7 | ||
| 2-Level LVCMOS Input Voltage Low | VIL | 0.7 | V | VDD = 2.25 V | 7 | ||
| 2-Level LVCMOS Input Voltage Low | VIL | 0.8 | V | VDD = 2.97 V | 7 | ||
| 2-Level LVCMOS Input Voltage High | VIH | 1.4 | V | VDD = 1.89 V | 7 | ||
| 2-Level LVCMOS Input Voltage High | VIH | 1.8 | V | VDD = 2.25 V | 7 | ||
| 2-Level LVCMOS Input Voltage High | VIH | 2.5 | V | VDD = 3.63 V | 7 | ||
| 3-Level Input Low Current | IILL | -20 | µA | See Note 4 | 8 | ||
| 3-Level Input Mid Current | IIMM | -2 | 2 | µA | See Note 4 | 8 | |
| 3-Level Input High Current | IIHH | 20 | µA | See Note 4 | 8 | ||
| LVCMOS Output Voltage Low | VOL | 0.4 | V | IO = 2 mA; VDD = 1.71 V | 8 | ||
| Disabled Leakage Current | IOZ | -100 | 100 | µA | RSTb = 0 | 8 | |
| I2C Input Current | III2C | -10 | 10 | µA | VIN = 0.1 x VDD to 0.9 x VDD | 9 | |
| I2C Output Voltage Low | VOLI2C | 0.4 | V | VDD = 2.5 or 3.3 V; IO = 3 mA | 9 | ||
| Output Rise/Fall (20-80%) at 212.5 MHz output, CMOS | CKOTRF | 2 | ns | CMOS output; VDD = 2.97 V; CLOAD = 5 pF | 12 | ||
| Output Duty Cycle Uncertainty at 622.08 MHz | CKODC | -40 | 40 | ps | 100 Ω load line-to-line; measured at 50% point (not for CMOS) | 12 | |
| Output Clock Skew | tSKEW | 100 | ps | CKOUTn to CKOUT_m at same frequency and signal format; PHASEOFFSET = 0; CKOUT_ALWAYS_ON = 1; SQ_ICAL = 1 | 12 | ||
| Phase Change due to Temperature Variation | tTEMP | 300 | 500 | ps | Max phase change from -40 to +85 °C | 12 | |
| Lock Time | tLOCKMP | 35 | 1200 | ms | fin = fout = 622.08 MHz; BW = 120 Hz; LVPECL; start of ICAL to of LOL | 13 | |
| Closed Loop Jitter Peaking | JPK | 0.05 | 0.1 | dB | fin = fout = 622.08 MHz; BW = 120 Hz; LVPECL | 13 | |
| Phase Noise at 1 kHz offset | CKOPN | -106 | -87 | dBc/Hz | fout = 622.08 MHz; 1 kHz offset | 13 | |
| Phase Noise at 10 kHz offset | CKOPN | -121 | -100 | dBc/Hz | fout = 622.08 MHz; 10 kHz offset | 13 | |
| Phase Noise at 100 kHz offset | CKOPN | -132 | -104 | dBc/Hz | fout = 622.08 MHz; 100 kHz offset | 13 | |
| Phase Noise at 1 MHz offset | CKOPN | -132 | -119 | dBc/Hz | fout = 622.08 MHz; 1 MHz offset | 13 | |
| Subharmonic Noise | SPSUBH | -88 | -76 | dBc | Phase noise @ 100 kHz offset | 13 | |
| Spurious Noise | SPSPUR | -93 | -70 | dBc | Max spur @ n x F3; n x F3 < 100 MHz | 13 | |
| Jitter Generation OC-192, 0.02-80 MHz | JGEN | 4.2 | 6.2 | psPP | Filter 0.02-80 MHz; DSPLL BW 120 Hz; fIN = fOUT = 622.08 MHz; LVPECL; VDD 2.5 V; TA 85 °C | 14 | |
| Jitter Generation OC-192, 0.02-80 MHz (RMS) | JGEN | 0.27 | 0.42 | psrms | Filter 0.02-80 MHz; DSPLL BW 120 Hz; fIN = fOUT = 622.08 MHz; LVPECL; VDD 2.5 V; TA 85 °C | 14 | |
| Jitter Generation OC-192, 4-80 MHz | JGEN | 3.7 | 6.4 | psPP | Filter 4-80 MHz; DSPLL BW 120 Hz; fIN = fOUT = 622.08 MHz; LVPECL; VDD 2.5 V; TA 85 °C | 14 | |
| Jitter Generation OC-192, 4-80 MHz (RMS) | JGEN | 0.14 | 0.31 | psrms | Filter 4-80 MHz; DSPLL BW 120 Hz; fIN = fOUT = 622.08 MHz; LVPECL; VDD 2.5 V; TA 85 °C | 14 | |
| Jitter Generation OC-192, 0.05-80 MHz (RMS) | JGEN | 0.26 | 0.41 | ps rms | Filter 0.05-80 MHz; DSPLL BW 120 Hz; fIN = fOUT = 622.08 MHz; LVPECL; VDD 2.5 V; TA 85 °C | 14 | |
| DC Supply Voltage | VDD | -0.5 | 3.8 | V | 15 | ||
| XA/XB Voltage Level Limits | XAVIN | 0 | 1.2 | V | 15 | ||
| Operating Junction Temperature | TJCT | -55 | 150 | ºC | 15 | ||
| Storage Temperature Range | TSTG | -55 | 150 | ºC | 15 | ||
| Thermal Resistance Junction to Ambient | JA | 32 | C°/W | Still air | 14 | ||
| Thermal Resistance Junction to Case | JC | 14 | C°/W | Still air | 14 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | PC | 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body | 66 |
CAD (KiCad official)
- Symbol:
SI5326C-C-GMR - Footprint:
Package_DFN_QFN:QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm - 3D model: QFN-36-EP(6x6) (KiCad packages3D, STEP)
- 3D model files:
si5326c-c-gmr-etched.step/si5326c-c-gmr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si5326c-c-gmr.step/si5326c-c-gmr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (72 pp, sha256
f3f2c9312d35874c, retrieved 2026-10-31, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).