← Commit history

Initial commit: component/si512

Ray ·911ff2831a ·
2 files changed +363
README.mdadded+69
@@ -0,0 +1,69 @@+# Si512++**Nanjing Zhongke Microelectronics** · RFID ICs · QFN-32-EP(5x5)++Si512 from Nanjing Zhongke Microelectronics, in a QFN-32-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SDI | input | I2C bus serial data input. |+| 2 | PVDD | power_in | Pad power supply pin, 2.3 to 3.6 V. |+| 3 | DVDD | power_in | Digital power supply pin, 2.3 to 3.6 V. |+| 4 | DVSS | power_in | Digital ground pin. |+| 5 | PVSS | power_in | Pad power supply ground pin. |+| 6 | NRSTPD | input | Not reset and power down; LOW switches off oscillator and current sinks, positive edge initiates reset. |+| 7 | MFIN | input | Communication interface input accepting digital serial data stream. |+| 8 | MFOUT | output | Communication interface output delivering serial data stream. |+| 9 | SVDD | power_in | Power supply for MFIN/MFOUT pads, 2.3 to 3.6 V. |+| 10 | TVSS | power_in | Transmitter ground supplying output stage of TX1 and TX2. |+| 11 | TX1 | output | Transmitter 1 output delivering modulated 13.56 MHz energy carrier. |+| 12 | TVDD | power_in | Transmitter power supply for TX1 and TX2 output stage, 2.3 to 3.6 V. |+| 13 | TX2 | output | Transmitter 2 output delivering modulated 13.56 MHz energy carrier. |+| 14 | TVSS | power_in | Transmitter ground supplying output stage of TX1 and TX2. |+| 15 | AVDD | power_in | Analog power supply pin, 2.3 to 3.6 V. |+| 16 | VMID | power_in | Internal reference voltage output pin. |+| 17 | RX | input | Receiver input for RF field detection at 13.56 MHz. |+| 18 | AVSS | power_in | Analog ground pin. |+| 19 | AUX1 | output | Auxiliary output pin used for testing and monitoring. |+| 20 | AUX2 | output | Auxiliary output pin used for testing and monitoring. |+| 21 | OSCIN | input | Crystal oscillator input to inverting amplifier; accepts 27.12 MHz external clock. |+| 22 | OSCOUT | output | Crystal oscillator output from inverting amplifier. |+| 23 | IRQ | output | Interrupt request output signaling interrupt event to host controller. |+| 24 | SD/NSS/RX | bidirectional | Multiplexed pin: I2C SDA (serial data), SPI NSS (chip select), or UART RX (receive address) depending on interface type. |+| 25 | D1/ADR_5 | bidirectional | Multiplexed pin: test port D1 or I2C bus address bit 5 input depending on interface type. |+| 26 | D2/ADR_4 | bidirectional | Multiplexed pin: test port D2 or I2C bus address bit 4 input depending on interface type. |+| 27 | D3/ADR_3 | bidirectional | Multiplexed pin: test port D3 or I2C bus address bit 3 input depending on interface type. |+| 28 | D4/ADR_2 | bidirectional | Multiplexed pin: test port D4 or I2C bus address bit 2 input depending on interface type. |+| 29 | D5/ADR_1/SCK/DTRQ | bidirectional | Multiplexed pin: test port D5, I2C address bit 1, SPI serial clock, or UART handshake request depending on interface type. |+| 30 | D6/ADR_0/MOSI/MX | bidirectional | Multiplexed pin: test port D6, I2C address bit 0, SPI master-out-slave-in, or UART controller output depending on interface type. |+| 31 | D7/SCL/MISO/TX | bidirectional | Multiplexed pin: test port D7, I2C serial clock, SPI master-in-slave-out, or UART data output depending on interface type. |+| 32 | EA | input | External address input pin to configure I2C slave address at power-up or reset. |+| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Nanjing Zhongke Microelectronics |+| Package | QFN-32-EP(5x5) |+| Category | RF And Wireless |+| Pins | 33 |++## CAD (KiCad official)++- Symbol: `Si512`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm`+- 3D model: QFN-32-EP(5x5) (KiCad packages3D, STEP)+- 3D model files: `si512-etched.step` / `si512-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `si512.step` / `si512.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Nanjing Zhongke Microelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588920144693506048) (134 pp, sha256 `bf6bea380f15b758`, retrieved 2026-09-17, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/si512-datasheet.pdf)
page.jsonadded+294
@@ -0,0 +1,294 @@+{+  "slug": "si512",+  "version": "0.1.0",+  "type": "component",+  "description": "Nanjing Zhongke Microelectronics RFID ICs, QFN-32-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "rf and wireless",+    "si512",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "si512.kicad_sym",+    "si512.kicad_mod",+    "si512.glb",+    "si512.step",+    "si512.lbr",+    "docs/hero.png",+    "docs/si512-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "Si512",+    "manufacturer": "Nanjing Zhongke Microelectronics",+    "package": "QFN-32-EP(5x5)",+    "pin_count": 33,+    "category": "RF And Wireless",+    "subcategory": "RFID ICs",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588920144693506048",+    "parts": {+      "symbol": "si512.kicad_sym",+      "footprint": "si512.kicad_mod",+      "model_3d": "si512-etched.glb",+      "model_3d_plain": "si512.glb",+      "model_3d_step": "si512-etched.step",+      "model_3d_step_plain": "si512.step",+      "lbr": "si512.lbr"+    },+    "distributor_links": {+      "lcsc": "C2916909"+    },+    "pins": [+      {+        "number": "1",+        "name": "SDI",+        "type": "input",+        "description": "I2C bus serial data input."+      },+      {+        "number": "2",+        "name": "PVDD",+        "type": "power_in",+        "description": "Pad power supply pin, 2.3 to 3.6 V."+      },+      {+        "number": "3",+        "name": "DVDD",+        "type": "power_in",+        "description": "Digital power supply pin, 2.3 to 3.6 V."+      },+      {+        "number": "4",+        "name": "DVSS",+        "type": "power_in",+        "description": "Digital ground pin."+      },+      {+        "number": "5",+        "name": "PVSS",+        "type": "power_in",+        "description": "Pad power supply ground pin."+      },+      {+        "number": "6",+        "name": "NRSTPD",+        "type": "input",+        "description": "Not reset and power down; LOW switches off oscillator and current sinks, positive edge initiates reset."+      },+      {+        "number": "7",+        "name": "MFIN",+        "type": "input",+        "description": "Communication interface input accepting digital serial data stream."+      },+      {+        "number": "8",+        "name": "MFOUT",+        "type": "output",+        "description": "Communication interface output delivering serial data stream."+      },+      {+        "number": "9",+        "name": "SVDD",+        "type": "power_in",+        "description": "Power supply for MFIN/MFOUT pads, 2.3 to 3.6 V."+      },+      {+        "number": "10",+        "name": "TVSS",+        "type": "power_in",+        "description": "Transmitter ground supplying output stage of TX1 and TX2."+      },+      {+        "number": "11",+        "name": "TX1",+        "type": "output",+        "description": "Transmitter 1 output delivering modulated 13.56 MHz energy carrier."+      },+      {+        "number": "12",+        "name": "TVDD",+        "type": "power_in",+        "description": "Transmitter power supply for TX1 and TX2 output stage, 2.3 to 3.6 V."+      },+      {+        "number": "13",+        "name": "TX2",+        "type": "output",+        "description": "Transmitter 2 output delivering modulated 13.56 MHz energy carrier."+      },+      {+        "number": "14",+        "name": "TVSS",+        "type": "power_in",+        "description": "Transmitter ground supplying output stage of TX1 and TX2."+      },+      {+        "number": "15",+        "name": "AVDD",+        "type": "power_in",+        "description": "Analog power supply pin, 2.3 to 3.6 V."+      },+      {+        "number": "16",+        "name": "VMID",+        "type": "power_in",+        "description": "Internal reference voltage output pin."+      },+      {+        "number": "17",+        "name": "RX",+        "type": "input",+        "description": "Receiver input for RF field detection at 13.56 MHz."+      },+      {+        "number": "18",+        "name": "AVSS",+        "type": "power_in",+        "description": "Analog ground pin."+      },+      {+        "number": "19",+        "name": "AUX1",+        "type": "output",+        "description": "Auxiliary output pin used for testing and monitoring."+      },+      {+        "number": "20",+        "name": "AUX2",+        "type": "output",+        "description": "Auxiliary output pin used for testing and monitoring."+      },+      {+        "number": "21",+        "name": "OSCIN",+        "type": "input",+        "description": "Crystal oscillator input to inverting amplifier; accepts 27.12 MHz external clock."+      },+      {+        "number": "22",+        "name": "OSCOUT",+        "type": "output",+        "description": "Crystal oscillator output from inverting amplifier."+      },+      {+        "number": "23",+        "name": "IRQ",+        "type": "output",+        "description": "Interrupt request output signaling interrupt event to host controller."+      },+      {+        "number": "24",+        "name": "SD/NSS/RX",+        "type": "bidirectional",+        "description": "Multiplexed pin: I2C SDA (serial data), SPI NSS (chip select), or UART RX (receive address) depending on interface type."+      },+      {+        "number": "25",+        "name": "D1/ADR_5",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D1 or I2C bus address bit 5 input depending on interface type."+      },+      {+        "number": "26",+        "name": "D2/ADR_4",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D2 or I2C bus address bit 4 input depending on interface type."+      },+      {+        "number": "27",+        "name": "D3/ADR_3",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D3 or I2C bus address bit 3 input depending on interface type."+      },+      {+        "number": "28",+        "name": "D4/ADR_2",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D4 or I2C bus address bit 2 input depending on interface type."+      },+      {+        "number": "29",+        "name": "D5/ADR_1/SCK/DTRQ",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D5, I2C address bit 1, SPI serial clock, or UART handshake request depending on interface type."+      },+      {+        "number": "30",+        "name": "D6/ADR_0/MOSI/MX",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D6, I2C address bit 0, SPI master-out-slave-in, or UART controller output depending on interface type."+      },+      {+        "number": "31",+        "name": "D7/SCL/MISO/TX",+        "type": "bidirectional",+        "description": "Multiplexed pin: test port D7, I2C serial clock, SPI master-in-slave-out, or UART data output depending on interface type."+      },+      {+        "number": "32",+        "name": "EA",+        "type": "input",+        "description": "External address input pin to configure I2C slave address at power-up or reset."+      },+      {+        "number": "33",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pins 10 and 14 (TVSS) have identical names and functions; datasheet repeats transmitter ground conne; Pins 24-31 are multiplexed between UART, SPI, I2C, and test functions; actual function depends on au",+          "exposed pad 33 added from the footprint"+        ],+        "pages_sent": 134,+        "cost_usd": 0.8408,+        "at": "2026-09-17T22:01:41"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588920144693506048",+        "pages": 134,+        "sha256": "bf6bea380f15b758",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 33,+        "described": 33,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file