Generated by kicad-footprint-generator · KiCad file format 20260206
Si4432-B1-FMR
SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)
Si4432-B1-FMR from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD_RF | power_in | +1.8 to +3.6 V supply input to all analog +1.7 V regulators, with +3.3 V recommended. |
| 2 | TX | output | Transmit PA output, open-drain, so the L-C match must supply VDD (+3.3 VDC nominal) to this pin. |
| 3 | RXp | input | Differential RF input of the LNA, positive side; see application schematic for example matching network. |
| 4 | RXn | input | Differential RF input of the LNA, negative side; see application schematic for example matching network. |
| 5 | NC | unconnected | No connect; not connected internally to any circuitry. |
| 6 | ANT | output | Extra antenna or TR switch control, a hardwired version of GPIO setting 11000 (Antenna 2), manually controllable by antdiv[2:0] bits in register 08h. |
| 7 | GPIO_0 | bidirectional | General purpose digital I/O configurable via registers 0Bh, 0Ch and 0Dh for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 8 | GPIO_1 | bidirectional | General purpose digital I/O configurable via registers 0Bh, 0Ch and 0Dh for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 9 | GPIO_2 | bidirectional | General purpose digital I/O configurable via registers 0Bh, 0Ch and 0Dh for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, low battery detect, TRSW and antenna diversity control. |
| 10 | VR_DIG | power_out | Regulated output of the digital 1.7 V regulator; a 1 µF decoupling capacitor is required. |
| 11 | NC | unconnected | Internally tied to the package paddle; leave unconnected or connect to GND only. |
| 12 | VDD_DIG | power_in | +1.8 to +3.6 V supply input to the digital +1.7 V regulator, with +3.3 V recommended. |
| 13 | SDO | output | 0-VDD V digital output providing serial readback of the internal control registers. |
| 14 | SDI | input | 0-VDD V digital serial data input for the 4-line serial data bus. |
| 15 | SCLK | input | 0-VDD V serial clock input for the 4-line serial bus; data is clocked in on positive edge transitions. |
| 16 | nSEL | input | 0-VDD V serial interface select/enable input for the 4-line serial bus, also signifying burst read/write mode. |
| 17 | nIRQ | output | Microcontroller interrupt status output, set low on any interrupt event; no external pull-up required but may be desirable with multiple interrupt lines. |
| 18 | XOUT | output | Crystal oscillator output for an external 30 MHz crystal, or external source drive with dc coupling at nominal 0.8 VDC and minimum 700 mVpp amplitude. |
| 19 | XIN | input | Crystal oscillator input for an external 30 MHz crystal; leave floating when driving an external source on XOUT. |
| 20 | SDN | input | 0-VDD V shutdown input; must be 0 in all modes except shutdown, and SDN=1 completely shuts down the chip and loses register contents. |
| 21 | PADDLE_GND | power_in | Exposed bottom paddle supplying RF and circuit ground for the entire chip; requires a good solder connection to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-20-EP(4x4) |
| Category | RF & Radio |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage Range | VDD | 1.8 | 3 | 3.6 | V | 7 | |
| Shutdown current | IShutdown | 15 | 50 | nA | RC Oscillator, Main Digital Regulator, and Low Power Digital Regulator OFF | 7 | |
| Standby current | IStandby | 450 | 800 | nA | Low Power Digital Regulator ON (Register values retained) and Main Digital Regulator, and RC Oscillator OFF | 7 | |
| Synthesizer Frequency Range Si4431/32 | FSYN | 240 | 930 | MHz | 8 | ||
| Reference Frequency Input Level | fREF_LV | 0.7 | 1.6 | V | External reference signal driving XOUT pin, peak-to-peak (VPP) | 8 | |
| Residual FM | FRMS | 2 | 4 | kHzRMS | Integrated over 250 kHz bandwidth (500 Hz lower bound of integration) | 8 | |
| RX Frequency Range Si4431/32 | FRX | 240 | 930 | MHz | 9 | ||
| RX Channel Bandwidth | BW | 2.6 | 620 | kHz | 9 | ||
| BER Variation vs Power Level | PRX_RES | 0 | 0.1 | ppm | Up to +5 dBm Input Level | 9 | |
| Spurious Emissions RX | POB_RX1 | -54 | dBm | Measured at RX pins | 9 | ||
| TX Frequency Range Si4431/32 | FTX | 240 | 930 | MHz | 10 | ||
| FSK Data Rate | DRFSK | 0.123 | 256 | kbps | 10 | ||
| OOK Data Rate | DROOK | 0.123 | 40 | kbps | 10 | ||
| Modulation Deviation | ∆f1 | 0.625 | 320 | kHz | 860-960 MHz | 10 | |
| Modulation Deviation | ∆f2 | 0.625 | 160 | kHz | 240-860 MHz | 10 | |
| Output Power Range Si4432 | PTX | 1 | 20 | dBm | 10 | ||
| Spurious Emissions TX <1 GHz | POB-TX1 | -54 | dBm | POUT = +13 dBm, Frequencies <1 GHz | 10 | ||
| Spurious Emissions TX 1-12.75 GHz | POB-TX2 | -54 | dBm | 1-12.75 GHz, excluding harmonics | 10 | ||
| 2nd Harmonic | P2HARM | -42 | dBm | Using reference design TX matching network and filter with max output power | 10 | ||
| 3rd Harmonic | P3HARM | -42 | dBm | Using reference design TX matching network and filter with max output power | 10 | ||
| Digital IO Rise Time | TRISE | 8 | ns | 0.1 x VDD to 0.9 x VDD, CL= 5 pF | 12 | ||
| Digital IO Fall Time | TFALL | 8 | ns | 0.9 x VDD to 0.1 x VDD, CL= 5 pF | 12 | ||
| Digital IO Input Capacitance | CIN | 1 | pF | 12 | |||
| Digital IO Logic Low Input Voltage | VIL | 0.6 | V | 12 | |||
| Digital IO Input Current | IIN | -100 | 100 | nA | 0<VIN< VDD | 12 | |
| Digital IO Logic Low Output Voltage | VOL | 0.6 | V | IOL<1 mA sink, VDD=1.8 V | 12 | ||
| GPIO Rise Time | TRISE | 8 | ns | 0.1 x VDD to 0.9 x VDD, CL= 10 pF, DRV<1:0>=HH | 12 | ||
| GPIO Fall Time | TFALL | 8 | ns | 0.9 x VDD to 0.1 x VDD, CL= 10 pF, DRV<1:0>=HH | 12 | ||
| GPIO Input Capacitance | CIN | 1 | pF | 12 | |||
| GPIO Logic Low Input Voltage | VIL | 0.6 | V | 12 | |||
| GPIO Input Current | IIN | -100 | 100 | nA | 0<VIN< VDD | 12 | |
| GPIO Input Current if Pullup Activated | IINP | 5 | 25 | µA | VIL=0 V | 12 | |
| GPIO Maximum Output Current LL | IOmaxLL | 0.1 | 0.5 | 0.8 | mA | DRV<1:0>=LL | 12 |
| GPIO Maximum Output Current LH | IOmaxLH | 0.9 | 2.3 | 3.5 | mA | DRV<1:0>=LH | 12 |
| GPIO Maximum Output Current HL | IOmaxHL | 1.5 | 3.1 | 4.8 | mA | DRV<1:0>=HL | 12 |
| GPIO Maximum Output Current HH | IOmaxHH | 1.8 | 3.6 | 5.4 | mA | DRV<1:0>=HH | 12 |
| GPIO Logic Low Output Voltage | VOL | 0.6 | V | IOL< IOmax sink, VDD=1.8 V | 12 | ||
| VDD to GND | -0.3 | 3.6 | V | 13 | |||
| Instantaneous VRF-peak to GND on TX Output Pin | -0.3 | 8 | V | 13 | |||
| Sustained VRF-peak to GND on TX Output Pin | -0.3 | 6.5 | V | 13 | |||
| Voltage on Digital Control Inputs | -0.3 | V | max printed as VDD + 0.3 V | 13 | |||
| Voltage on Analog Inputs | -0.3 | V | max printed as VDD + 0.3 V | 13 | |||
| RX Input Power | 10 | dBm | 13 | ||||
| Operating Ambient Temperature Range | TA | -40 | 85 | °C | 13 | ||
| Junction Temperature | TJ | 125 | °C | 13 | |||
| Storage Temperature Range | TSTG | -55 | 125 | °C | 13 | ||
| Thermal Impedance | θJA | 30 | °C/W | 13 | |||
| Sleep current | ISleep | 1 | µA | RC Oscillator and Low Power Digital Regulator ON (Register values retained) and Main Digital Regulator OFF | 7 | ||
| Ready mode current | IReady | 800 | µA | Crystal Oscillator and Main Digital Regulator ON, all other blocks OFF. Crystal Oscillator buffer disabled | 7 | ||
| Tune mode current | ITune | 8.5 | mA | Synthesizer and regulators enabled | 7 | ||
| RX mode current | IRX | 18.5 | mA | 7 | |||
| TX mode current Si4432 | ITX_+20 | 85 | mA | txpow[2:0] = 111 (+20 dBm), Using Silicon Labs' Reference Design | 7 | ||
| RX Sensitivity 2 kbps | PRX_2 | -121 | dBm | (BER < 0.1%) (2 kbps, GFSK, BT = 0.5, f = 5 kHz) | 9 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | abs | wireless knowledge base at www.silabs.com/support/knowledgebase. | 63 |
CAD (KiCad official)
- Symbol:
Si4432-B1-FMR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
si4432-b1-fmr-etched.step/si4432-b1-fmr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si4432-b1-fmr.step/si4432-b1-fmr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (75 pp, sha256
4c8122caa6c795b7, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).