main
History Download
Ray Publish 0.1.0 b0e8b9d

SI4060-C2A-GM

SILICON LABS · RF Transceiver ICs · QFN-20-EP(4x4)

SI4060-C2A-GM from SILICON LABS, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SDN input Shutdown input (0 to VDD V digital); SDN must be 0 in all modes except Shutdown, and SDN = 1 fully shuts the chip down, losing register contents; it can also be used to reset the chip.
2 NC unconnected Leave pin floating.
3 NC unconnected Leave pin floating.
4 TX output Transmit output is an open-drain PA output, so the L-C match must supply VDD (+3.3 V nominal) to this pin.
5 NC unconnected Not connected internally; the datasheet recommends connecting this pin to GND per the reference design schematic.
6 VDD power_in Supply voltage input to internal regulators, +1.8 to +3.8 V, with +3.3 V recommended.
7 TXRAMP output Programmable bias output with ramp capability for an external FET PA (see section 5.2 of the datasheet).
8 VDD power_in Supply voltage input to internal regulators, +1.8 to +3.8 V, with +3.3 V recommended.
9 GPIO0 bidirectional General purpose digital I/O that can be configured through registers for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, and low battery detect.
10 GPIO1 bidirectional General purpose digital I/O; the extracted pin table gives no separate function text for this pin, so its function is set through the registers like the other GPIO pins.
11 nIRQ output General microcontroller interrupt status output that goes low when any interrupt event occurs; no external pull-up is required, though one may be desirable when multiple interrupt lines are connected.
12 SCLK input Serial clock input (0 to VDD V) for the 4-line serial bus; data is clocked in on positive edge transitions.
13 SDO output Serial data readback output (0 to VDD V) for reading the internal control registers.
14 SDI input Serial data input (0 to VDD V) carrying the data stream for the 4-line serial bus.
15 nSEL input Serial interface select input (0 to VDD V) providing the select/enable function for the 4-line serial bus.
16 XOUT output Crystal oscillator output; connect to an external 25 to 32 MHz crystal, or leave floating when driving the chip from an external source on XIN.
17 XIN input Crystal oscillator input; connect to an external 25 to 32 MHz crystal or to an external reference source.
18 GND power_in Ground; leave floating with a crystal per the reference schematic, or connect to a separate TCXO ground when using a TCXO.
19 GPIO2 bidirectional General purpose digital I/O that can be configured through registers for functions such as microcontroller clock output, FIFO status, POR, wake-up timer, and low battery detect.
20 GPIO3 bidirectional General purpose digital I/O; the extracted pin table gives no separate function text for this pin, so its function is set through the registers like the other GPIO pins.
21 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer SILICON LABS
Package QFN-20-EP(4x4)
Category RF & Radio
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage Range VDD 1.8 3.3 3.8 V 4
Operating Ambient Temperature Range TA -40 85 °C 10
Junction Temperature Maximum Value Tj 105 °C 10
Storage Temperature Range TSTG -55 150 °C 10
Thermal Impedance Junction to Ambient JA 25 °C/W Based on RF evaluation board measurements 10
VDD to GND VDD -0.3 3.8 V 10
Instantaneous VRF-peak to GND on TX Output Pin VRF-peak -0.3 8 V 10
Sustained VRF-peak to GND on TX Output Pin VRF-peak -0.3 6.5 V 10
Voltage on Analog Inputs -0.7 V 10
Synthesizer Frequency Range (Si4063/60) 850-1050 MHz band FSYN 850 1050 MHz 5
Synthesizer Frequency Range (Si4063/60) 350-525 MHz band FSYN 350 525 MHz 5
Synthesizer Frequency Range (Si4063/60) 284-350 MHz band FSYN 284 350 MHz 5
Synthesizer Frequency Range (Si4063/60) 142-175 MHz band FSYN 142 175 MHz 5
TX Frequency Range 850-1050 MHz band FTX 850 1050 MHz 6
TX Frequency Range 350-525 MHz band FTX 350 525 MHz 6
TX Frequency Range 284-350 MHz band FTX 284 350 MHz 6
TX Frequency Range 142-175 MHz band FTX 142 175 MHz 6
(G)FSK Data Rate DRFSK 0.1 500 kbps 6
4(G)FSK Data Rate DR4FSK 0.2 1000 kbps 6
OOK Data Rate DROOK 0.1 120 kbps 6
Output Power Range (Si4060) PTX60 -20 12.5 dBm Typical range at 3.3 V with Class E match optimized for best PA efficiency 6
Output Power Variation (Si4060) 9.5 10 10.5 dBm At 10 dBm PA power setting, 915 MHz, Class E match, 3.3 V, 25 °C 7
Logic Low Input Current IIN -1 1 µA 0<VIN<VDD 9
Input Current If Pullup is Activated IINP 1 4 µA VIL = 0 V 9
Crystal Oscillator Range (XTAL Range) XTALRange 25 32 MHz Tested using an external clock source (similar to TCXO) 8
Maximum allowed XIN swing 1.8 V peak-to-peak 25
POR Reset Time tPOR 6 ms 8

CAD (KiCad official)

  • Symbol: SI4060-C2A-GM
  • Footprint: Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm
  • 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: si4060-c2a-gm-etched.step / si4060-c2a-gm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); si4060-c2a-gm.step / si4060-c2a-gm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: SILICON LABS datasheet (37 pp, sha256 6c2f75f5b458d69f, retrieved 2026-10-30, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF