3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSI1063-A-GM
SILICON LABS · RF Transceiver ICs · QFN-36-EP(5x6)
SI1063-A-GM from SILICON LABS, in a QFN-36-EP(5x6). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | P2.7/C2D | bidirectional | Port 2.7 is GPIO only, cannot be routed by the Crossbar, cannot be configured as an analog input, and carries the bidirectional C2 Debug Interface data signal. |
| 2 | XTAL4 | passive | SmaRTClock oscillator crystal output for a 32.768 kHz crystal, as described in Section 20 of the datasheet. |
| 3 | XTAL3 | passive | SmaRTClock oscillator crystal input for a 32.768 kHz crystal, as described in Section 20 of the datasheet. |
| 4 | P1.6 | bidirectional | Port 1.6 general-purpose I/O that can be assigned to analog, digital or external interrupt functions, per the Port I/O section. |
| 5 | P1.5 | bidirectional | Port 1.5 general-purpose I/O that can be assigned to analog, digital or external interrupt functions, per the Port I/O section. |
| 6 | P1.4 | bidirectional | Port 1.4 general-purpose I/O that can be assigned to analog, digital or external interrupt functions, per the Port I/O section. |
| 7 | XOUT | passive | Crystal oscillator output that connects to an external 25 to 32 MHz crystal, or is left floating when an external source drives XIN. |
| 8 | XIN | input | Crystal oscillator input that connects to an external 25 to 32 MHz crystal or to an external clock source. |
| 9 | GND_RF | power_in | Required ground for the digital and analog portions of the EZRadioPRO peripheral. |
| 10 | GPIO2 | bidirectional | General-purpose I/O controlled by the EZRadioPRO peripheral, configurable for functions such as clock output, FIFO status, POR, Wake-Up Timer, TRSW and antenna diversity control. |
| 11 | GPIO3 | bidirectional | General-purpose I/O controlled by the EZRadioPRO peripheral, configurable for functions such as clock output, FIFO status, POR, Wake-Up Timer, TRSW and antenna diversity control. |
| 12 | RXP | input | Differential RF input of the EZRadioPRO LNA, used with an external matching network. |
| 13 | RXN | input | Differential RF input of the EZRadioPRO LNA, used with an external matching network. |
| 14 | TX | output | EZRadioPRO transmit RF output; the PA output is open-drain, so the L-C match must supply 1.8 to 3.6 VDC to this pin. |
| 15 | GND_RF | power_in | Required ground for the digital and analog portions of the EZRadioPRO peripheral. |
| 16 | GND_RF | power_in | Required ground for the digital and analog portions of the EZRadioPRO peripheral. |
| 17 | GND_RF | power_in | Required ground for the digital and analog portions of the EZRadioPRO peripheral. |
| 18 | VDD_RF | power_in | Power supply for the analog portion of the EZRadioPRO peripheral, which must be 1.8 to 3.6 V. |
| 19 | TXRAMP | output | Programmable bias output with ramp capability for an external FET PA. |
| 20 | VDD_RF | power_in | Power supply for the analog portion of the EZRadioPRO peripheral, which must be 1.8 to 3.6 V. |
| 21 | GPIO0 | bidirectional | General-purpose I/O controlled by the EZRadioPRO peripheral, configurable for functions such as clock output, FIFO status, POR, Wake-Up Timer, TRSW and antenna diversity control. |
| 22 | GPIO1 | bidirectional | General-purpose I/O controlled by the EZRadioPRO peripheral, configurable for functions such as clock output, FIFO status, POR, Wake-Up Timer, TRSW and antenna diversity control. |
| 23 | IRQ | output | EZRadioPRO interrupt status pin that is driven low to indicate a pending interrupt; it is an open-drain output with a 220 k internal pullup and an external pull-up is recommended. |
| 24 | P0.6/CNVSTR | bidirectional | Port 0.6 general-purpose I/O that also serves as the external convert start input for ADC0. |
| 25 | P0.5/RX | bidirectional | Port 0.5 general-purpose I/O that also serves as the UART0 RX pin. |
| 26 | P0.4/TX | bidirectional | Port 0.4 general-purpose I/O that also serves as the UART0 TX pin. |
| 27 | P0.3/XTAL2 | bidirectional | Port 0.3 general-purpose I/O that also serves as the external oscillator excitation driver output for a crystal or resonator, or as the external clock input in CMOS clock or capacitor/RC modes. |
| 28 | P0.2/XTAL1 | bidirectional | Port 0.2 general-purpose I/O that also serves as the external oscillator return for a crystal or resonator, or as the external clock input. |
| 29 | P0.1/AGND | bidirectional | Port 0.1 general-purpose I/O that can also be used as the optional analog ground reference for the VREF circuit. |
| 30 | P0.0/VREF | bidirectional | Port 0.0 general-purpose I/O that can serve as an external VREF input or the internal VREF output, for which external decoupling capacitors are recommended. |
| 31 | GND_MCU/DC- | power_in | DC-DC converter return current path; in single-cell battery mode it is typically not connected to ground, and in dual-cell battery mode it must be connected directly to ground. |
| 32 | GND_MCU/VBAT- | power_in | Required ground for the entire MCU except for the EZRadioPRO peripheral. |
| 33 | VDD_MCU/DC+ | power_in | MCU supply that must be 1.8 to 3.6 V and always greater than VBAT, and that is also the positive dc-dc converter output requiring a 1 µF ceramic capacitor between DC+ and DC- in single-cell mode. |
| 34 | DCEN | input | DC-DC enable pin that must connect to VBAT through a 0.68 µH inductor in single-cell battery mode and directly to ground in dual-cell battery mode. |
| 35 | VBAT+ | power_in | Battery supply that must be 0.9 to 1.8 V in single-cell battery mode and 1.8 to 3.6 V in dual-cell battery mode. |
| 36 | RST/C2CK | bidirectional | Open-drain device reset output from the internal POR or VDD monitor that an external source can drive low for at least 15 µs, with a 1 to 5 k pullup to VDD_MCU recommended, and that also serves as the C2 Debug Interface clock. |
| 37 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SILICON LABS |
| Package | QFN-36-EP(5x6) |
| Category | RF & Radio |
| Pins | 37 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 42 | |||
| Voltage on any Px.x I/O Pin or RST with Respect to GND | -0.3 | 5.8 | V | VDD > 2.2 V | 42 | ||
| Voltage on any Px.x I/O Pin or RST with Respect to GND | -0.3 | V | VDD < 2.2 V | 42 | |||
| Voltage on VBAT with Respect to GND | VBAT | -0.3 | 2 | V | One-Cell Mode | 42 | |
| Voltage on VBAT with Respect to GND | VBAT | -0.3 | 4 | V | Two-Cell Mode | 42 | |
| Voltage on VDD_MCU or VDD_MCU/DC+ with Respect to GND | VDD_MCU/DC+ | -0.3 | 4 | V | 42 | ||
| Maximum Total Current through VBAT, DCEN, VDD_MCU/DC+ or GND | 500 | mA | 42 | ||||
| Maximum Output Current Sunk by RST or any Px.x Pin | 100 | mA | 42 | ||||
| Maximum Total Current through all Px.x Pins | 200 | mA | 42 | ||||
| DC-DC Converter Output Power | 110 | mW | 42 | ||||
| Battery Supply Voltage (VBAT) | VBAT | 0.9 | 1.2 | 1.8 | V | One-Cell Mode | 43 |
| Battery Supply Voltage (VBAT) | VBAT | 1.8 | 2.4 | 3.6 | V | Two-Cell Mode | 43 |
| Supply Voltage (VDD_MCU/DC+) | VDD_MCU/DC+ | 1.8 | 1.9 | 3.6 | V | One-Cell Mode | 43 |
| Supply Voltage (VDD_MCU/DC+) | VDD_MCU/DC+ | 1.8 | 2.4 | 3.6 | V | Two-Cell Mode | 43 |
| SYSCLK (System Clock) | SYSCLK | 0 | 25 | MHz | 43 | ||
| TSYSL (SYSCLK Low Time) | TSYSL | 18 | ns | 43 | |||
| Specified Operating Temperature Range | -40 | 85 | °C | 43 | |||
| Digital Supply Current, CPU Active (IDD) | IDD | 4.1 | 5 | mA | VDD = 1.8-3.6 V, F = 24.5 MHz (includes precision oscillator current) | 43 | |
| Digital Supply Current, CPU Inactive, Idle Mode (IDD) | IDD | 2.5 | 3 | mA | VDD = 1.8-3.6 V, F = 24.5 MHz (includes precision oscillator current) | 44 | |
| Output Low Voltage | VOL | 0.6 | V | High Drive Strength, PnDRV.n = 1; IOL = 8.5 mA, Port I/O | 52 | ||
| Output Low Voltage | VOL | 0.1 | V | High Drive Strength, PnDRV.n = 1; IOL = 10 µA | 52 | ||
| Input Low Voltage | VIL | 0.6 | V | VDD = 2.0 to 3.6 V | 52 | ||
| RST Output Low Voltage | 0.6 | V | IOL = 1.4 mA | 57 | |||
| RST Input Low Voltage | 0.6 | V | VDD = 2.0 to 3.6 V | 57 | |||
| VDD_MCU Monitor Threshold (VRST) Early Warning | VRST | 1.8 | 1.85 | 1.9 | V | Early Warning Reset Trigger (all power modes except Sleep) | 57 |
| VDD_MCU Monitor Threshold (VRST) Reset Trigger | VRST | 1.7 | 1.75 | 1.8 | V | Reset Trigger (all power modes except Sleep) | 57 |
| VDD Ramp Time for Power On | 3 | ms | One-cell Mode: VBAT Ramp 0-0.9 V; Two-cell Mode: VBAT Ramp 0-1.8 V | 57 | |||
| Missing Clock Detector Timeout | 100 | 650 | 1000 | µs | Time from last system clock rising edge to reset initiation | 57 | |
| Idle Mode Wake-up Time | 2 | 3 | SYSCLKs | 58 | |||
| Flash Size | 32768 | bytes | Si1061, Si1063, Si1065 | 58 | |||
| Erase Cycle Time | 28 | 32 | 36 | ms | 58 | ||
| Write Cycle Time | 57 | 64 | 71 | µs | 58 | ||
| Internal Precision Oscillator Frequency | 24 | 24.5 | 25 | MHz | VDD = 1.8 to 3.6 V; TA = -40 to +85 °C; factory-calibrated settings | 59 | |
| Internal Low-Power Oscillator Frequency | 18 | 20 | 22 | MHz | VDD = 1.8 to 3.6 V; TA = -40 to +85 °C; factory-calibrated settings | 59 | |
| ADC0 Integral Nonlinearity | -1 | 0.5 | 1 | LSB | 60 | ||
| ADC0 Full Scale Error | -2.5 | 1 | 2.5 | LSB | 60 | ||
| ADC0 Signal-to-Noise Plus Distortion | 54 | 58 | dB | 10 kHz sine-wave single-ended input, 1 dB below Full Scale, 300 ksps | 60 | ||
| ADC0 Track/Hold Acquisition Time | 1.5 | us | 60 | ||||
| Internal High-Speed Reference Output Voltage | 1.6 | 1.65 | 1.7 | V | -40 to +85 °C, VDD = 1.8-3.6 V (REFSL[1:0] = 11) | 62 | |
| Internal Precision Reference Output Voltage | 1.645 | 1.68 | 1.715 | V | -40 to +85 °C, VDD = 1.8-3.6 V (REFSL[1:0] = 00, REFOE = 1) | 62 | |
| Comparator Input Offset Voltage | -7 | 7 | mV | 63 | |||
| DC-DC Converter Input Voltage Range | 0.9 | 1.8 | V | VBAT = 0.9 to 1.8 V | 65 | ||
| DC-DC Converter Output Voltage Range | 1.73 | 1.8 | 1.87 | V | Target Output = 1.8 V | 65 | |
| DC-DC Converter Output Voltage Range | 3.18 | 3.3 | 3.42 | V | Target Output = 3.3 V | 65 | |
| DC-DC Converter Output Current (based on output power spec) | 36 | mA | Target Output = 1.8 V | 65 | |||
| DC-DC Converter Output Power | 65 | mW | 65 | ||||
| DC-DC Converter Capacitance Connected to Output | 0.8 | 1 | 2 | µF | 65 | ||
| VREG0 Input Voltage Range | 1.8 | 3.6 | V | 66 | |||
| Supply Voltage Range (radio) | VDD | 1.8 | 3.3 | 3.6 | V | VDD_RF supply | 67 |
| Synthesizer Frequency Range (Si1060/61/62/63, Si1080/81/82/83) | FSYN | 850 | 1050 | MHz | 850-1050 MHz band | 68 | |
| RX Channel Bandwidth (Si1060/61/62/63, Si1080/81/82/83) | BW | 1.1 | 850 | kHz | Guaranteed by design | 69 | |
| (G)FSK Data Rate (Si1060/61/62/63, Si1080/81/82/83) | DRFSK | 0.1 | 500 | kbps | Guaranteed by characterization | 73 | |
| Output Power Range (Si1062/63/64/65, Si1082/83/84/85) | PTX60 | -40 | 13 | dBm | Guaranteed by characterization; output power depends on matching and layout | 74 | |
| VDD to GND | VDD | -0.3 | 3.6 | V | Radio absolute maximum ratings | 77 | |
| Instantaneous VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 8 | V | 77 | ||
| Sustained VRF-peak to GND on TX Output Pin | VRF-peak | -0.3 | 6.5 | V | 77 | ||
| Storage Temperature Range | TSTG | -55 | 125 | °C | 77 | ||
| Maximum Junction Temperature | TJ | 125 | °C | 77 | |||
| Thermal Impedance | JA | 30 | °C/W | Table 4.22 single 'Value' column, JEDEC thermal impedance | 77 |
CAD (KiCad official)
- Symbol:
SI1063-A-GM - Footprint:
Package_DFN_QFN:QFN-36-1EP_5x6mm_P0.5mm_EP3.6x4.6mm - 3D model: QFN-36-EP(5x6) (KiCad packages3D, STEP)
- 3D model files:
si1063-a-gm-etched.step/si1063-a-gm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);si1063-a-gm.step/si1063-a-gm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SILICON LABS datasheet (358 pp, sha256
176bb082a846e11e, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).