← Commit history

sgm706b-txs8g: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·648577f442 · ·parent 28e6a2a
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "SGM706B-TXS8G",+    "manufacturer": "SGMICRO",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "Supervisor and Reset ICs",+    "parts": {+      "symbol": "sgm706b-txs8g.kicad_sym",+      "footprint": "sgm706b-txs8g.kicad_mod",+      "model_3d": "sgm706b-txs8g-etched.glb",+      "model_3d_plain": "sgm706b-txs8g.glb",+      "model_3d_step": "sgm706b-txs8g-etched.step",+      "model_3d_step_plain": "sgm706b-txs8g.step",+      "lbr": "sgm706b-txs8g.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "nMR",+        "type": "input",+        "description": "Manual Reset input, active-low. Internal ~234 µA (at VCC = 5 V) pull-up current, so it can be driven by CMOS/TTL logic or a simple switch to GND. If unused, leave open or tie to VCC."+      },+      {+        "number": "2",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage input. Operating range 1.0 V to 5.5 V; monitored against the 3.08 V (typ) reset threshold for the -T suffix. Absolute max -0.3 V to 6.0 V."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference for all inputs and outputs."+      },+      {+        "number": "4",+        "name": "PFI",+        "type": "input",+        "description": "Power-Fail voltage monitor input. Compared internally to a 1.25 V reference; nPFO asserts low when PFI < 1.25 V. Typically driven from a resistor divider off the monitored rail. If unused, tie to GND or VCC."+      },+      {+        "number": "5",+        "name": "nPFO",+        "type": "output",+        "description": "Power-Fail comparator output, active-low, open-source-limited. Goes low when PFI < 1.25 V and remains high while PFI > 1.25 V."+      },+      {+        "number": "6",+        "name": "WDI",+        "type": "input",+        "description": "Watchdog input. Must be toggled (rising or falling edge, ≥90 ns pulse) within the 1.6 s (typ) watchdog timeout, otherwise nWDO is pulled low. Timer is held clear while a reset is asserted or WDI is three-stated; leaving WDI floating disables the watchdog. When disabling by tri-stating, ensure WDI enters high-Z from a high level."+      },+      {+        "number": "7",+        "name": "nRESET",+        "type": "output",+        "description": "Active-low reset output. Asserted low for 200 ms (typ) after VCC rises above the reset threshold or nMR is released; held low while VCC is below threshold or nMR is low. Guaranteed valid down to VCC = 1 V."+      },+      {+        "number": "8",+        "name": "nWDO",+        "type": "output",+        "description": "Watchdog output, active-low. Pulled low when the watchdog times out (no WDI edge within 1.6 s typ) or when VCC is below the reset threshold, and remains low until the watchdog is cleared. Unlike nRESET, nWDO has no minimum pulse width and returns high immediately once the fault clears (assuming VCC is above threshold)."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}