component
SGM2553YN6G
Public Made by Adomby adom
SGMICRO Power Distribution Switches, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownSGM2553YN6G
SGMICRO · Power Distribution Switches · SOT-23-6
SGM2553YN6G from SGMICRO, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input voltage; connect a 0.1µF or greater ceramic capacitor from IN to GND as close to the IC as possible. |
| 2 | GND | power_in | Ground; the datasheet specifies connecting it externally to the exposed pad. |
| 3 | EN | input | Enable input; logic high turns on the power switch, with VIH of 1.4V minimum and VIL of 0.3V maximum. |
| 4 | FAULT | output | Active-low open-drain output asserted during over-current, over-temperature, or reverse-voltage conditions; continuous FAULT sink current is limited to 25mA absolute maximum and 0 to 10mA recommended. |
| 5 | ILIM | passive | External resistor sets the current limit threshold; recommended 20kΩ ≤ RILIM ≤ 387kΩ. |
| 6 | OUT | power_out | Power switch output; continuous output current range is 0A to 1.5A. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SGMICRO |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Enable Voltage Range | 0 | 5.5 | V | 2 | |||
| Continuous Output Current Range | 0 | 1.5 | A | 2 | |||
| Current Limit Threshold Resistor Range | RILIM | 20 | 387 | kΩ | 2 | ||
| Continuous FAULT Sink Current Range | 0 | 10 | mA | 2 | |||
| Minimum Input Decoupling Capacitance | 0.1 | μF | 2 | ||||
| Operating Temperature Range | -40 | 85 | ℃ | 2 | |||
| VIN, VOUT, EN, ILIM and FAULT to GND | -0.3 | 6 | V | 2 | |||
| ILIM Source Current | ILIM | 1 | mA | 2 | |||
| Junction Temperature | 150 | ℃ | 2 | ||||
| Storage Temperature Range | -65 | 150 | ℃ | 2 | |||
| Lead Temperature (Soldering, 10s) | 260 | ℃ | Soldering, 10s | 2 | |||
| High-side MOSFET On Resistance | RDS(ON) | 90 | 130 | mΩ | 4 | ||
| Output Rise Time | tR | 1.8 | 3.5 | ms | VIN = 5.5V, CL = 1μF, RL = 100Ω, Figure 2 | 4 | |
| Output Rise Time | tR | 1.1 | 2.5 | ms | VIN = 2.5V, CL = 1μF, RL = 100Ω, Figure 2 | 4 | |
| Output Fall Time | tF | 0.3 | 0.4 | ms | VIN = 5.5V | 4 | |
| Logic High of Enable Pin | VIH | 1.4 | V | 4 | |||
| Logic Low of Enable Pin | VIL | 0.3 | V | 4 | |||
| Input Current | IEN | 0.01 | 1 | μA | VEN = 5.5V | 4 | |
| Turn-On Time | tON | 3 | 5 | ms | CL = 1μF, RL = 100Ω, Figure 2 | 4 | |
| Turn-Off Time | tOFF | 1.6 | 2.5 | ms | 4 | ||
| Current Limit Threshold (Maximum DC output current IOUT delivered to load) | ILIM | 460 | 545 | 610 | mA | VIN = 3V, RILIM = 68kΩ, OUT connected to GND through 4Ω | 4 |
| Response Time to Short Circuit | tIOS | 2 | μs | Figure 3 | 4 | ||
| Reverse-Voltage Comparator Trip Point | 115 | 160 | 205 | mV | 4 | ||
| Time from Reverse-Voltage Condition to MOSFET Turn-Off | 3.5 | 5.5 | 7.5 | ms | 4 | ||
| Supply Current, Low-Level Output | IIN(OFF) | 0.1 | 2.5 | μA | VIN = 5.5V, No load on OUT, VEN = 0V | 4 | |
| Supply Current, High-Level Output (RILIM = 36kΩ) | IIN(ON) | 71 | 105 | μA | RILIM = 36kΩ, VIN = 5.5V, No load on OUT | 4 | |
| Supply Current, High-Level Output (RILIM = 68kΩ) | IIN(ON) | 62 | 95 | μA | RILIM = 68kΩ | 4 | |
| Reverse Leakage Current | IREV | 0.01 | 1 | μA | VOUT = 5.5V, VIN = 0V | 4 | |
| Under-Voltage Lockout Threshold | VUVLO | 2.36 | 2.47 | V | VIN Rising | 4 | |
| Under-Voltage Lockout Threshold Hysteresis | 140 | mV | 4 | ||||
| FAULT Output Low Voltage | 95 | 150 | mV | IFAULT = 1mA | 4 | ||
| Off-State Leakage | 0.02 | 1 | μA | VFAULT = 5.5V | 4 | ||
| FAULT Deglitch (over-current) | 6.5 | 10 | 14 | ms | FAULT assertion or de-assertion due to over-current condition | 4 | |
| FAULT Deglitch (reverse-voltage) | 3.5 | 5.5 | 7.5 | ms | FAULT assertion or de-assertion due to reverse-voltage condition | 4 | |
| Thermal Shutdown Threshold | 140 | ℃ | 4 | ||||
| Thermal Shutdown Threshold in Current Limit | 115 | ℃ | 4 | ||||
| Thermal Shutdown Hysteresis | 10 | ℃ | 4 | ||||
| Package Thermal Resistance, SOT-23-6 | θJA | 260 | ℃/W | SOT-23-6 package | 2 |
CAD (KiCad official)
- Symbol:
SGM2553YN6G - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
sgm2553yn6g-etched.step/sgm2553yn6g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sgm2553yn6g.step/sgm2553yn6g.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SGMICRO datasheet (15 pp, sha256
53846d51e6194fd2, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).