← Commit history
README.mdadded+56@@ -0,0 +1,56 @@+# SG3524DR++**UMW** · DC-DC Converters · SOP-16++SG3524DR from UMW, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | INV.INPUT | input | Inverting input of the internal error amplifier. Tied to the feedback network of the switching regulator's output-voltage divider. |+| 2 | N.I.INPUT | input | Non-inverting input of the internal error amplifier. Normally driven from a reference-derived setpoint (e.g. divider off VREF). |+| 3 | OSC.OUTPUT | output | Oscillator sawtooth/sync output. Provides a ~3.5V peak clock/sync waveform (0.3-1.5µs pulse width) usable for external synchronization or as a blanking/dead-time signal. |+| 4 | +C.L. SENSE | input | Non-inverting input of the current-limit sense amplifier. Connect across the current-sense resistor with pin 5; limit threshold is ~200mV. |+| 5 | -C.L. SENSE | input | Inverting input of the current-limit sense amplifier. Paired with pin 4 across the current-sense element to fold back the PWM when overcurrent is detected. |+| 6 | RT | passive | Timing resistor terminal. External RT from this pin to ground sets the oscillator charging current; recommended range 1.8kΩ to 100kΩ. |+| 7 | CT | passive | Timing capacitor terminal. External CT from this pin to ground sets the oscillator ramp; recommended range 0.001µF to 0.1µF. Fosc ≈ 1.30/(RT·CT). |+| 8 | GROUND | power_in | Device signal and power ground return (0V). All internal references, oscillator, comparators and output transistor emitters (when tied here) are referred to this node. |+| 9 | COMPENSATION | output | Error-amplifier output / PWM comparator input. Loop-compensation network (typically a series R-C to INV.INPUT) is connected here to shape the control-loop response. |+| 10 | SHUTDOWN | input | Active-high shutdown input. Pulling above the turn-off threshold (typ 0.8V, 0.5-1.2V) inhibits both PWM outputs. Tie low or leave unused for normal operation. |+| 11 | EA | output | Emitter of output transistor A (uncommitted NPN). Used as the output when the stage is configured as an emitter follower, or grounded when the collector is used as the switching node. |+| 12 | CA | output | Collector of output transistor A (uncommitted NPN). Rated 40V / 100mA per package, 50mA per output; used for single-ended or push-pull drive to an external switch or transformer. |+| 13 | CB | output | Collector of output transistor B (uncommitted NPN). Complementary phase to CA; toggles alternately at half the oscillator frequency for push-pull operation. |+| 14 | EB | output | Emitter of output transistor B (uncommitted NPN). Serves as the emitter-follower output or is grounded when CB is used as the switching node. |+| 15 | +VIN | power_in | Main supply input. Recommended 8V to 40V; absolute max 40V. Powers the reference, oscillator, error amp and output transistors. Bypass locally to GROUND. |+| 16 | VREF | power_out | Internally regulated 5V reference output (4.8-5.2V), source capability up to 20mA (short-circuit current 25-150mA). Used to bias external dividers and the error-amp non-inverting input. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | UMW |+| Package | SOP-16 |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++- `SG3524DR`+- `SG3524DRD`++## CAD (KiCad official)++- Symbol: `SG3524DR`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOP-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [UMW datasheet](docs/sg3524dr-datasheet.pdf) (12 pp, sha256 `366bbb2f3ad77931`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/sg3524dr-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "sg3524dr",+ "version": "0.1.0",+ "type": "component",+ "description": "UMW DC-DC Converters, SOP-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "pmic",+ "sg3524dr"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "sg3524dr.kicad_sym",+ "sg3524dr.kicad_mod",+ "sg3524dr.glb",+ "sg3524dr.step",+ "sg3524dr.lbr",+ "docs/hero.png",+ "docs/sg3524dr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}