main
Ray
sec1210i-cn-02: the pins were read twice by one model (sonnet); say so instead of 'cross-checked by two models'
33cd305
SEC1210I-CN-02
Microchip Tech · Interface - Specialized · QFN-24(5x5)
SEC1210I-CN-02 from Microchip Tech, in a QFN-24(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SC2_RST_N | output | Smart Card 2 reset output (also GPIO18); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active. |
| 2 | SC2_VCC | power_out | Smart Card 2 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor. |
| 3 | VDD5 | power_in | 5.0 V (or VBUS) power input; the supply input range is 3.6 V to 5.5 V. |
| 4 | SC1_C8 | bidirectional | Smart Card 1 C8 contact for standard or proprietary use as input and/or output (also GPIO4). |
| 5 | SC1_C4 | bidirectional | Smart Card 1 C4 contact for cards that support Function Code (also GPIO3). |
| 6 | SC1_IO | bidirectional | Smart Card 1 bidirectional serial data pin (also GPIO0), which should be held low when the interface is not active. |
| 7 | SC1_CLK | output | Smart Card 1 clock output (also GPIO1), which should be held low when the interface is not active. |
| 8 | SC1_RST_N | output | Smart Card 1 reset output (also GPIO2); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active. |
| 9 | SC1_VCC | power_out | Smart Card 1 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor. |
| 10 | SC1_PRSNT_N/JTAG_TMS | bidirectional | Active-low Smart Card 1 presence detect with software-activated internal pull-up, alternatively JTAG_TMS in debug mode, GPIO6 or Timer 0 input. |
| 11 | SPI1_MISO/RXD | bidirectional | SPI1 host data input to the controller (needs a weak internal pull-down at all times), alternatively UART RXD input or GPIO8. |
| 12 | SPI1_CLK/CTS | bidirectional | SPI1 clock output in host mode, alternatively UART CTS or GPIO10. |
| 13 | SPI1_CE/RTS | bidirectional | Active-low SPI1 chip-enable output in host mode (drive high in idle if SPI1 is disabled), alternatively UART RTS or GPIO11. |
| 14 | SPI1_MOSI/TXD | bidirectional | SPI1 host data output from the controller, alternatively UART TXD output or GPIO9. |
| 15 | TEST | input | Chip test signal with a weak pull-down at reset; it must be tied low externally if the test function is not used. |
| 16 | USB_DM | bidirectional | USB D- data line connecting to the upstream USB bus, with integrated series termination resistor. |
| 17 | USB_DP | bidirectional | USB D+ data line connecting to the upstream USB bus, with integrated 1.5 k pull-up and series resistor. |
| 18 | VDD33 | power_out | 3.3 V internal regulator output for USB and GPIO I/O supply, requiring an external 1 µF decoupling capacitor. |
| 19 | JTAG_CLK | bidirectional | JTAG debug clock input with weak pull-down, which can be left floating or grounded when not used. |
| 20 | SC_LED_ACT_N/JTAG_TDO | bidirectional | Driver for the active LED, alternatively JTAG_TDO in debug mode, GPIO5 or Timer 2 t2ex input. |
| 21 | SC2_PRSNT_N/JTAG_TDI | bidirectional | Active-low Smart Card 2 presence detect with software-activated pull-up, alternatively JTAG_TDI or GPIO19, with weak pull-down at reset. |
| 22 | RESET_N | input | Active-low analog reset input (Vil=100 mV) that resets the chip and enters STOP mode, with a pulse at least 1 µs wide. |
| 23 | SC2_IO | bidirectional | Smart Card 2 bidirectional serial data pin (also GPIO16), which should be held low when the interface is not active. |
| 24 | SC2_CLK | output | Smart Card 2 clock output (also GPIO17), which should be held low when the interface is not active. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-24(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTOR | -55 | 150 | °C | 188 | ||
| VDD5 supply voltage | VDD5 | -0.3 | 5.5 | V | 188 | ||
| Voltage on any signal pin | -0.3 | 5.5 | V | 188 | |||
| Voltage on USB_DP and USB_DM pins | -0.3 | 3.6 | V | 3.3 V 10% | 188 | ||
| Voltage on RESET_N | 0 | V | VDD5 (Note 18-3) | 188 | |||
| Operating Temperature | TA | -40 | 85 | °C | Ambient temperature in air; industrial range per Notes 18-1 and 18-2 | 189 | |
| 5.0V supply voltage | VDD5 | 3.6 | 5.5 | V | 189 | ||
| Voltage on USB_DP and USB_DM pins | 3 | 3.6 | V | If VDD5 drops below 3.6V, then the MAX becomes VDD5 | 189 | ||
| Voltage on RESET_N | 0 | V | 189 | ||||
| Voltage on any signal pin | -0.3 | 5.5 | V | Other than USB_DP, USB_DM, Smart Card pins, RESET_N | 189 | ||
| VDD5 supply rise time | tRT | 400 | ns | Figure 18-1 | 189 | ||
| Low Output Level | VOL | 0.4 | V | IOL = -8 mA | 189 | ||
| 8 mA I/O sinking current | IOL8 | 8.3 | 12.6 | 18.4 | mA | VOUT = 0.4V | 189 |
| 8 mA I/O sinking output impedance | ROL8 | 21.7 | 31.6 | 48.3 | VOUT = 0.4V | 189 | |
| 8 mA I/O sourcing current | IOH8 | 8.1 | 11.6 | 16 | mA | VOUT = VDD33 - 0.4V | 189 |
| 8 mA I/O sourcing output impedance | ROH8 | 25 | 34.6 | 50 | VOUT = VDD33 - 0.4V | 189 | |
| Output Leakage | IIH5 | 1 | µA | VIN= 0 to VDD33,27°C | 189 | ||
| Output Leakage | IIH5 | 1.4 | 8 | 12 | µA | VIN = 0 to 5.5V, 27°C | 189 |
| Output Leakage | IIH5 | 20 | µA | VIN = 0 to 5.5V, 85°C | 189 | ||
| Output Leakage | IIH5 | 80 | µA | VIN=0 to 5.5V,125°C | 189 | ||
| Low Input Level | VIL | -0.3 | 0.8 | V | 189 | ||
| High Input Level | VIH5 | 2 | 5.5 | V | 189 | ||
| Hysteresis | VHYSI | 336 | 399 | 459 | mV | 189 | |
| Pull-Down | RDPD | 46 | 65 | 90 | k | Vpad = VDD33 | 189 |
| Pull-Down current | IDPD | 33 | 50 | 79 | µA | Vpad = VDD33 | 189 |
| Pull-Up | RDPU | 53 | 66 | 80 | k | Vpad = 0V | 189 |
| Pull-Up current | IDPU | 38 | 50 | 68 | µA | Vpad = 0V | 189 |
| RESET_N Rise Time | Trst_r | 100 | ns | RESET_N pad | 190 | ||
| RESET_N Fall Time | Trst_f | 100 | ns | RESET_N pad | 190 | ||
| RESET_N Low Input level | VILRST | 0.1 | V | RESET_N low causes STOP mode entry | 190 | ||
| Internal oscillator 48 MHz accuracy with USB dynamic trim | F48acc | 0.1 | 0.2 | % | Internal oscillator @ 48 MHz with USB Dynamic Trim enabled | 190 | |
| Internal oscillator 48 MHz accuracy without USB dynamic trim | F48accd | 0.82 | 1.5 | % | Internal oscillator @ 48 MHz without USB Dynamic Trim enabled | 190 | |
| Internal oscillator 8 MHz accuracy | F8acc | 0.78 | 1.83 | % | Internal oscillator @ 8 MHz | 190 | |
| Internal oscillator 4 MHz accuracy | F4acc | 0.78 | 1.83 | % | Internal oscillator @ 4 MHz | 190 | |
| Smart Card Power Supply Voltage (Class A) | VSC1_VCC, VSC2_VCC | 4.6 | V | Class A mode, ISC1_VCC = 0 to 55 mA | 190 | ||
| Smart Card Power Supply Voltage (Class B) | VSC1_VCC, VSC2_VCC | 2.76 | 3 | 3.24 | V | Class B mode | 190 |
| Smart Card Power Supply Voltage (Class C) | VSC1_VCC, VSC2_VCC | 1.66 | 1.8 | 1.94 | V | Class C mode | 190 |
| Smart Card Power Supply current | ISC1, ISC2 | 55 | mA | Class A/B/C | 190 | ||
| Smart Card Over Current Sense (OCS) Detection | IOCS1, IOCS2 | 110 | mA | 190 | |||
| Detection Time on OCS | tOSCDET | 1 | µs | 190 | |||
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | 5 | ms | SEC1110/SEC1210 A1 version | 190 | ||
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | 500 | µs | All Later versions | 190 | ||
| SC1_VCC/SC2_VCC Turn On Time | tSCON | 1 | ms | 1.0 µF load | 190 | ||
| SC1_CLK/SC2_CLK Low Output Level (Class A) | VOL | 0 | 0.4 | V | Class A; @ CL=30pF | 191 | |
| SC1_CLK/SC2_CLK Low Output Level (Class B) | VOL | 0 | 0.4 | V | Class B; @ CL=30pF | 191 | |
| SC1_CLK/SC2_CLK Low Output Level (Class C) | VOL | 0 | V | Class C; @ CL=30pF | 191 | ||
| SC1_CLK/SC2_CLK Rise Time | tR | 9.9 | 13 | 16.67 | ns | @ CL = 30 pF, Rload=33 | 191 |
| SC1_CLK/SC2_CLK Fall Time | tF | 6.5 | 10 | 16.2 | ns | @ CL = 30 pF, Rload=33 | 191 |
| SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trimming on) | 0.1 | 0.25 | % | USB Dynamic Trimming is on | 191 | ||
| SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trim off) | 0.82 | 1.5 | % | USB Dynamic trim is off | 191 | ||
| SC1_CLK/SC2_CLK Clock Duty Cycle | 48 | 52 | % | Oscillator in 48 MHz mode | 191 | ||
| SC1_CLK/SC2_CLK Frequency | FSCx_CLK | 1 | 4.8 | MHz | Generated by dividing 48 MHz by an integer ranging from 10 to 48 | 191 |
CAD (KiCad official)
- Symbol:
SEC1210I-CN-02 - Footprint:
Package_DFN_QFN:QFN-24-1EP_5x5mm_P0.65mm_EP3.2x3.2mm - 3D model: QFN-24(5x5) (KiCad packages3D, STEP)
- 3D model files:
sec1210i-cn-02-etched.step/sec1210i-cn-02-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sec1210i-cn-02.step/sec1210i-cn-02.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (220 pp, sha256
3d50372dd19b6208, retrieved 2026-11-09, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SEC1210I-CN-02
**Microchip Tech** · Interface - Specialized · QFN-24(5x5)
SEC1210I-CN-02 from Microchip Tech, in a QFN-24(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SC2_RST_N | output | Smart Card 2 reset output (also GPIO18); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active. |
| 2 | SC2_VCC | power_out | Smart Card 2 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor. |
| 3 | VDD5 | power_in | 5.0 V (or VBUS) power input; the supply input range is 3.6 V to 5.5 V. |
| 4 | SC1_C8 | bidirectional | Smart Card 1 C8 contact for standard or proprietary use as input and/or output (also GPIO4). |
| 5 | SC1_C4 | bidirectional | Smart Card 1 C4 contact for cards that support Function Code (also GPIO3). |
| 6 | SC1_IO | bidirectional | Smart Card 1 bidirectional serial data pin (also GPIO0), which should be held low when the interface is not active. |
| 7 | SC1_CLK | output | Smart Card 1 clock output (also GPIO1), which should be held low when the interface is not active. |
| 8 | SC1_RST_N | output | Smart Card 1 reset output (also GPIO2); a low pulse resets the card and triggers an ATR, and it should be held low when the interface is not active. |
| 9 | SC1_VCC | power_out | Smart Card 1 supply output settable to 1.8, 3.0 or 5.0 V depending on card type, powered down at reset, and requires an external 1 µF capacitor. |
| 10 | SC1_PRSNT_N/JTAG_TMS | bidirectional | Active-low Smart Card 1 presence detect with software-activated internal pull-up, alternatively JTAG_TMS in debug mode, GPIO6 or Timer 0 input. |
| 11 | SPI1_MISO/RXD | bidirectional | SPI1 host data input to the controller (needs a weak internal pull-down at all times), alternatively UART RXD input or GPIO8. |
| 12 | SPI1_CLK/CTS | bidirectional | SPI1 clock output in host mode, alternatively UART CTS or GPIO10. |
| 13 | SPI1_CE/RTS | bidirectional | Active-low SPI1 chip-enable output in host mode (drive high in idle if SPI1 is disabled), alternatively UART RTS or GPIO11. |
| 14 | SPI1_MOSI/TXD | bidirectional | SPI1 host data output from the controller, alternatively UART TXD output or GPIO9. |
| 15 | TEST | input | Chip test signal with a weak pull-down at reset; it must be tied low externally if the test function is not used. |
| 16 | USB_DM | bidirectional | USB D- data line connecting to the upstream USB bus, with integrated series termination resistor. |
| 17 | USB_DP | bidirectional | USB D+ data line connecting to the upstream USB bus, with integrated 1.5 k pull-up and series resistor. |
| 18 | VDD33 | power_out | 3.3 V internal regulator output for USB and GPIO I/O supply, requiring an external 1 µF decoupling capacitor. |
| 19 | JTAG_CLK | bidirectional | JTAG debug clock input with weak pull-down, which can be left floating or grounded when not used. |
| 20 | SC_LED_ACT_N/JTAG_TDO | bidirectional | Driver for the active LED, alternatively JTAG_TDO in debug mode, GPIO5 or Timer 2 t2ex input. |
| 21 | SC2_PRSNT_N/JTAG_TDI | bidirectional | Active-low Smart Card 2 presence detect with software-activated pull-up, alternatively JTAG_TDI or GPIO19, with weak pull-down at reset. |
| 22 | RESET_N | input | Active-low analog reset input (Vil=100 mV) that resets the chip and enters STOP mode, with a pulse at least 1 µs wide. |
| 23 | SC2_IO | bidirectional | Smart Card 2 bidirectional serial data pin (also GPIO16), which should be held low when the interface is not active. |
| 24 | SC2_CLK | output | Smart Card 2 clock output (also GPIO17), which should be held low when the interface is not active. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-24(5x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 25 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | TSTOR | -55 | | 150 | °C | | 188 |
| VDD5 supply voltage | VDD5 | -0.3 | | 5.5 | V | | 188 |
| Voltage on any signal pin | | -0.3 | | 5.5 | V | | 188 |
| Voltage on USB_DP and USB_DM pins | | -0.3 | | 3.6 | V | 3.3 V 10% | 188 |
| Voltage on RESET_N | | 0 | | | V | VDD5 (Note 18-3) | 188 |
| Operating Temperature | TA | -40 | | 85 | °C | Ambient temperature in air; industrial range per Notes 18-1 and 18-2 | 189 |
| 5.0V supply voltage | VDD5 | 3.6 | | 5.5 | V | | 189 |
| Voltage on USB_DP and USB_DM pins | | 3 | | 3.6 | V | If VDD5 drops below 3.6V, then the MAX becomes VDD5 | 189 |
| Voltage on RESET_N | | 0 | | | V | | 189 |
| Voltage on any signal pin | | -0.3 | | 5.5 | V | Other than USB_DP, USB_DM, Smart Card pins, RESET_N | 189 |
| VDD5 supply rise time | tRT | 400 | | | ns | Figure 18-1 | 189 |
| Low Output Level | VOL | | | 0.4 | V | IOL = -8 mA | 189 |
| 8 mA I/O sinking current | IOL8 | 8.3 | 12.6 | 18.4 | mA | VOUT = 0.4V | 189 |
| 8 mA I/O sinking output impedance | ROL8 | 21.7 | 31.6 | 48.3 | | VOUT = 0.4V | 189 |
| 8 mA I/O sourcing current | IOH8 | 8.1 | 11.6 | 16 | mA | VOUT = VDD33 - 0.4V | 189 |
| 8 mA I/O sourcing output impedance | ROH8 | 25 | 34.6 | 50 | | VOUT = VDD33 - 0.4V | 189 |
| Output Leakage | IIH5 | | | 1 | µA | VIN= 0 to VDD33,27°C | 189 |
| Output Leakage | IIH5 | 1.4 | 8 | 12 | µA | VIN = 0 to 5.5V, 27°C | 189 |
| Output Leakage | IIH5 | | | 20 | µA | VIN = 0 to 5.5V, 85°C | 189 |
| Output Leakage | IIH5 | | | 80 | µA | VIN=0 to 5.5V,125°C | 189 |
| Low Input Level | VIL | -0.3 | | 0.8 | V | | 189 |
| High Input Level | VIH5 | 2 | | 5.5 | V | | 189 |
| Hysteresis | VHYSI | 336 | 399 | 459 | mV | | 189 |
| Pull-Down | RDPD | 46 | 65 | 90 | k | Vpad = VDD33 | 189 |
| Pull-Down current | IDPD | 33 | 50 | 79 | µA | Vpad = VDD33 | 189 |
| Pull-Up | RDPU | 53 | 66 | 80 | k | Vpad = 0V | 189 |
| Pull-Up current | IDPU | 38 | 50 | 68 | µA | Vpad = 0V | 189 |
| RESET_N Rise Time | Trst_r | 100 | | | ns | RESET_N pad | 190 |
| RESET_N Fall Time | Trst_f | 100 | | | ns | RESET_N pad | 190 |
| RESET_N Low Input level | VILRST | | | 0.1 | V | RESET_N low causes STOP mode entry | 190 |
| Internal oscillator 48 MHz accuracy with USB dynamic trim | F48acc | | 0.1 | 0.2 | % | Internal oscillator @ 48 MHz with USB Dynamic Trim enabled | 190 |
| Internal oscillator 48 MHz accuracy without USB dynamic trim | F48accd | | 0.82 | 1.5 | % | Internal oscillator @ 48 MHz without USB Dynamic Trim enabled | 190 |
| Internal oscillator 8 MHz accuracy | F8acc | | 0.78 | 1.83 | % | Internal oscillator @ 8 MHz | 190 |
| Internal oscillator 4 MHz accuracy | F4acc | | 0.78 | 1.83 | % | Internal oscillator @ 4 MHz | 190 |
| Smart Card Power Supply Voltage (Class A) | VSC1_VCC, VSC2_VCC | 4.6 | | | V | Class A mode, ISC1_VCC = 0 to 55 mA | 190 |
| Smart Card Power Supply Voltage (Class B) | VSC1_VCC, VSC2_VCC | 2.76 | 3 | 3.24 | V | Class B mode | 190 |
| Smart Card Power Supply Voltage (Class C) | VSC1_VCC, VSC2_VCC | 1.66 | 1.8 | 1.94 | V | Class C mode | 190 |
| Smart Card Power Supply current | ISC1, ISC2 | | | 55 | mA | Class A/B/C | 190 |
| Smart Card Over Current Sense (OCS) Detection | IOCS1, IOCS2 | 110 | | | mA | | 190 |
| Detection Time on OCS | tOSCDET | | | 1 | µs | | 190 |
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | | | 5 | ms | SEC1110/SEC1210 A1 version | 190 |
| SC1_VCC/SC2_VCC Turn Off Time | tSCOFF | | | 500 | µs | All Later versions | 190 |
| SC1_VCC/SC2_VCC Turn On Time | tSCON | | | 1 | ms | 1.0 µF load | 190 |
| SC1_CLK/SC2_CLK Low Output Level (Class A) | VOL | 0 | | 0.4 | V | Class A; @ CL=30pF | 191 |
| SC1_CLK/SC2_CLK Low Output Level (Class B) | VOL | 0 | | 0.4 | V | Class B; @ CL=30pF | 191 |
| SC1_CLK/SC2_CLK Low Output Level (Class C) | VOL | 0 | | | V | Class C; @ CL=30pF | 191 |
| SC1_CLK/SC2_CLK Rise Time | tR | 9.9 | 13 | 16.67 | ns | @ CL = 30 pF, Rload=33 | 191 |
| SC1_CLK/SC2_CLK Fall Time | tF | 6.5 | 10 | 16.2 | ns | @ CL = 30 pF, Rload=33 | 191 |
| SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trimming on) | | | 0.1 | 0.25 | % | USB Dynamic Trimming is on | 191 |
| SC1_CLK/SC2_CLK Clock Accuracy (USB dynamic trim off) | | | 0.82 | 1.5 | % | USB Dynamic trim is off | 191 |
| SC1_CLK/SC2_CLK Clock Duty Cycle | | 48 | | 52 | % | Oscillator in 48 MHz mode | 191 |
| SC1_CLK/SC2_CLK Frequency | FSCx_CLK | 1 | | 4.8 | MHz | Generated by dividing 48 MHz by an integer ranging from 10 to 48 | 191 |
## CAD (KiCad official)
- Symbol: `SEC1210I-CN-02`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_5x5mm_P0.65mm_EP3.2x3.2mm`
- 3D model: QFN-24(5x5) (KiCad packages3D, STEP)
- 3D model files: `sec1210i-cn-02-etched.step` / `sec1210i-cn-02-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sec1210i-cn-02.step` / `sec1210i-cn-02.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/sec1210i-cn-02-datasheet.pdf) (220 pp, sha256 `3d50372dd19b6208`, retrieved 2026-11-09, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sec1210i-cn-02-datasheet.pdf)