← Commit history
page.json+8−5@@ -32,7 +32,7 @@ "number": "1", "name": "CHRG", "type": "output",- "description": "Open-drain charge status output. Pulled low by an internal N-channel MOSFET while charging; goes high-impedance when charge completes. In the low-battery lockout condition CHRG also goes high-impedance; with ~1 \u03bcF from BAT to GND this pin will flash quickly when no battery is present, giving a battery-present indication. Typical weak pull-down current 20 \u03bcA at VCHRG=5 V."+ "description": "Open-drain charge status output. Pulled low by an internal N-channel MOSFET while charging; goes high-impedance when charge completes. In the low-battery lockout condition CHRG also goes high-impedance; with ~1 μF from BAT to GND this pin will flash quickly when no battery is present, giving a battery-present indication. Typical weak pull-down current 20 μA at VCHRG=5 V." }, { "number": "2",@@ -44,19 +44,19 @@ "number": "3", "name": "BAT", "type": "power_out",- "description": "Charge current output to the Li-Ion cell. Supplies charge current and regulates the float voltage to 4.2 V \u00b11%. An internal precision resistor divider senses this pin; when the battery is reversed the internal protection prevents damage to the VBAT ESD diode and about 0.7 mA flows from GND to BAT."+ "description": "Charge current output to the Li-Ion cell. Supplies charge current and regulates the float voltage to 4.2 V ±1%. An internal precision resistor divider senses this pin; when the battery is reversed the internal protection prevents damage to the VBAT ESD diode and about 0.7 mA flows from GND to BAT." }, { "number": "4", "name": "VCC", "type": "power_in",- "description": "Positive supply input to the charger. Operates from 4.25 V to 6.5 V and requires at least a 1 \u03bcF bypass capacitor. When VCC drops within 30 mV of VBAT the SD8052 enters standby and BAT current falls below 2 \u03bcA."+ "description": "Positive supply input to the charger. Operates from 4.25 V to 6.5 V and requires at least a 1 μF bypass capacitor. When VCC drops within 30 mV of VBAT the SD8052 enters standby and BAT current falls below 2 μA." }, { "number": "5", "name": "PROG", "type": "bidirectional",- "description": "Charge-current program, monitor, and shutdown pin. A resistor from PROG to GND (1% tolerance) sets constant-current charge current: IBAT = (VPROG/RPROG) \u00d7 1000, with VPROG \u2248 1.0 V in constant-current mode. Pulling PROG above the ~1.21 V manual-shutdown threshold (via a ~3 \u03bcA pull-up from an external source) puts the part into shutdown (input current drops to ~25 \u03bcA); driving PROG above the ~2.4 V clamp yields about 1.5 mA sink to that pin. Reconnecting PROG to GND resumes normal charging."+ "description": "Charge-current program, monitor, and shutdown pin. A resistor from PROG to GND (1% tolerance) sets constant-current charge current: IBAT = (VPROG/RPROG) × 1000, with VPROG ≈ 1.0 V in constant-current mode. Pulling PROG above the ~1.21 V manual-shutdown threshold (via a ~3 μA pull-up from an external source) puts the part into shutdown (input current drops to ~25 μA); driving PROG above the ~2.4 V clamp yields about 1.5 mA sink to that pin. Reconnecting PROG to GND resumes normal charging." } ], "provenance": {@@ -121,5 +121,8 @@ "docs/sd8052-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }