main
Ray
Publish 0.1.0
805f5c7
SCT2612STER
SCT · DC-DC Converters · ESOP-8
SCT2612STER from SCT, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Bias supply for the high-side MOSFET gate driver; connect a 0.1uF capacitor from BOOT to SW, which charges while SW is low. |
| 2 | VIN | power_in | Input supply voltage with an operating range of 4.2V to 60V; place a local bypass capacitor from VIN to GND as close as possible to the pins. |
| 3 | EN | input | Enable input with an internal pull-up current source; pull below 1.05V to disable the converter, float or tie to VIN to enable it, and use a resistor divider from VIN to set the input UVLO threshold. |
| 4 | RT/CLK | input | Sets the switching frequency with a resistor to ground (100kHz to 1.2MHz) or accepts an external clock in the same 100kHz to 1.2MHz band via PLL synchronization, reverting to the resistor-set frequency if clock edges stop. |
| 5 | FB | input | Inverting input of the transconductance error amplifier that regulates to 0.8V typical (0.792V to 0.808V) through an external feedback divider from the output. |
| 6 | PGOOD | output | Open-drain power-good output that asserts low when the output is low due to thermal shutdown, dropout, over-voltage or EN shutdown. |
| 7 | GND | power_in | Ground reference for the device. |
| 8 | SW | output | Regulator switching node that connects to the external power inductor. |
| 9 | Thermal Pad | power_in | Heat dissipation path from the die that is electrically connected to GND and must be soldered to a ground plane on the PCB for proper operation and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN voltage | -0.3 | 65 | V | 2 | |||
| BOOT voltage | -0.3 | 72 | V | 2 | |||
| SW voltage | -1 | 65 | V | 2 | |||
| BOOT-SW voltage | -0.3 | 6 | V | 2 | |||
| PGOOD, FB, RT/CLK voltage | -0.3 | 6 | V | 2 | |||
| Operating junction temperature | TJ | -40 | 150 | °C | 2 | ||
| Storage temperature | TSTG | -65 | 150 | °C | 2 | ||
| Input voltage range | VIN | 4.5 | 60 | V | 3 | ||
| Output voltage range | VOUT | 0.8 | 57 | V | 3 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 3 | ||
| Operating input voltage | VIN | 4.2 | 60 | V | 3 | ||
| Shutdown current from VIN pin | ISHDN | 2 | 5 | μA | EN=0, no load | 3 | |
| Reference voltage of FB | VREF | 0.792 | 0.8 | 0.808 | V | 3 | |
| High-side power MOSFET peak current limit threshold | ILIM_HS | 2.4 | 2.8 | 3.2 | A | 3 | |
| Using RT mode frequency range | FRANGE_RT | 100 | 1200 | kHz | 4 | ||
| Switching frequency | FSW | 450 | 500 | 550 | kHz | RRT=200 kΩ(1%) | 4 |
| Frequency range using CLK mode | FRANGE_CLK | 100 | 1200 | kHz | 4 | ||
| Input UVLO threshold | VIN_UVLO | 3.5 | V | VIN rising | 3 | ||
| Input UVLO hysteresis | 400 | mV | 3 | ||||
| Quiescent current from VIN pin | IQ | 100 | μA | EN floating, no load, non-switching, BOOT-SW=5V, RRT=200 kΩ | 3 | ||
| High-side MOSFET on-resistance | RDSON_H | 220 | mΩ | VBOOT-VSW=5V | 3 | ||
| Enable high threshold | VEN_H | 1.2 | V | 4 | |||
| Enable low threshold | VEN_L | 1.05 | V | 4 | |||
| Enable pin pull-up current | IEN_L | 1 | μA | EN=1V | 4 | ||
| Enable pin pull-up current | IEN_H | 4 | uA | EN=1.5V | 4 | ||
| Soft start time | TSS | 4 | ms | 4 | |||
| Minimum on-time | tON_MIN | 100 | ns | VIN=24V | 4 | ||
| Power-good flag under voltage tripping threshold (power good) | VPG_UV | 95 | % | POWER GOOD (% of FB voltage) | 4 | ||
| Power-good flag under voltage tripping threshold (power bad) | VPG_UV | 90 | % | POWER BAD (% of FB voltage) | 4 | ||
| Power-good flag over voltage tripping threshold (power bad) | VPG_OV | 110 | % | POWER BAD (% of FB voltage) | 4 | ||
| Power-good flag over voltage tripping threshold (power good) | VPG_OV | 105 | % | POWER GOOD (% of FB voltage) | 4 | ||
| PGOOD leakage current at high level output | IPG | 200 | nA | VPull-Up = 5V | 4 | ||
| PGOOD low level output voltage | VPG_LOW | 0.1 | V | IPull-Up = 1 mA | 4 | ||
| Feedback overvoltage with respect to reference voltage (rising) | VOVP | 110 | % | VFB/VREF rising | 4 | ||
| Feedback overvoltage with respect to reference voltage (falling) | VOVP | 105 | % | VFB/VREF falling | 4 | ||
| BOOT UVLO reference voltage | VBOOTUV | 2.5 | V | BOOT-SW falling | 4 | ||
| BOOT UVLO hysteresis | 230 | mV | 4 | ||||
| Thermal shutdown threshold | TSD | 172 | °C | TJ rising | 4 | ||
| Thermal shutdown hysteresis | 12 | °C | 4 | ||||
| Junction-to-ambient thermal resistance | θja | 42 | °C/W | standard board | 3 | ||
| Junction-to-top characterization parameter | ψjt | 5.9 | °C/W | 3 |
CAD (KiCad official)
- Symbol:
SCT2612STER - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
sct2612ster-etched.step/sct2612ster-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);sct2612ster.step/sct2612ster.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SCT datasheet (20 pp, sha256
e2572ef44d882d59, retrieved 2026-11-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# SCT2612STER
**SCT** · DC-DC Converters · ESOP-8
SCT2612STER from SCT, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_in | Bias supply for the high-side MOSFET gate driver; connect a 0.1uF capacitor from BOOT to SW, which charges while SW is low. |
| 2 | VIN | power_in | Input supply voltage with an operating range of 4.2V to 60V; place a local bypass capacitor from VIN to GND as close as possible to the pins. |
| 3 | EN | input | Enable input with an internal pull-up current source; pull below 1.05V to disable the converter, float or tie to VIN to enable it, and use a resistor divider from VIN to set the input UVLO threshold. |
| 4 | RT/CLK | input | Sets the switching frequency with a resistor to ground (100kHz to 1.2MHz) or accepts an external clock in the same 100kHz to 1.2MHz band via PLL synchronization, reverting to the resistor-set frequency if clock edges stop. |
| 5 | FB | input | Inverting input of the transconductance error amplifier that regulates to 0.8V typical (0.792V to 0.808V) through an external feedback divider from the output. |
| 6 | PGOOD | output | Open-drain power-good output that asserts low when the output is low due to thermal shutdown, dropout, over-voltage or EN shutdown. |
| 7 | GND | power_in | Ground reference for the device. |
| 8 | SW | output | Regulator switching node that connects to the external power inductor. |
| 9 | Thermal Pad | power_in | Heat dissipation path from the die that is electrically connected to GND and must be soldered to a ground plane on the PCB for proper operation and thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SCT |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN voltage | | -0.3 | | 65 | V | | 2 |
| BOOT voltage | | -0.3 | | 72 | V | | 2 |
| SW voltage | | -1 | | 65 | V | | 2 |
| BOOT-SW voltage | | -0.3 | | 6 | V | | 2 |
| PGOOD, FB, RT/CLK voltage | | -0.3 | | 6 | V | | 2 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 2 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 2 |
| Input voltage range | VIN | 4.5 | | 60 | V | | 3 |
| Output voltage range | VOUT | 0.8 | | 57 | V | | 3 |
| Operating junction temperature | TJ | -40 | | 150 | °C | | 3 |
| Operating input voltage | VIN | 4.2 | | 60 | V | | 3 |
| Shutdown current from VIN pin | ISHDN | | 2 | 5 | μA | EN=0, no load | 3 |
| Reference voltage of FB | VREF | 0.792 | 0.8 | 0.808 | V | | 3 |
| High-side power MOSFET peak current limit threshold | ILIM_HS | 2.4 | 2.8 | 3.2 | A | | 3 |
| Using RT mode frequency range | FRANGE_RT | 100 | | 1200 | kHz | | 4 |
| Switching frequency | FSW | 450 | 500 | 550 | kHz | RRT=200 kΩ(1%) | 4 |
| Frequency range using CLK mode | FRANGE_CLK | 100 | | 1200 | kHz | | 4 |
| Input UVLO threshold | VIN_UVLO | | 3.5 | | V | VIN rising | 3 |
| Input UVLO hysteresis | | | 400 | | mV | | 3 |
| Quiescent current from VIN pin | IQ | | 100 | | μA | EN floating, no load, non-switching, BOOT-SW=5V, RRT=200 kΩ | 3 |
| High-side MOSFET on-resistance | RDSON_H | | 220 | | mΩ | VBOOT-VSW=5V | 3 |
| Enable high threshold | VEN_H | | 1.2 | | V | | 4 |
| Enable low threshold | VEN_L | | 1.05 | | V | | 4 |
| Enable pin pull-up current | IEN_L | | 1 | | μA | EN=1V | 4 |
| Enable pin pull-up current | IEN_H | | 4 | | uA | EN=1.5V | 4 |
| Soft start time | TSS | | 4 | | ms | | 4 |
| Minimum on-time | tON_MIN | | 100 | | ns | VIN=24V | 4 |
| Power-good flag under voltage tripping threshold (power good) | VPG_UV | | 95 | | % | POWER GOOD (% of FB voltage) | 4 |
| Power-good flag under voltage tripping threshold (power bad) | VPG_UV | | 90 | | % | POWER BAD (% of FB voltage) | 4 |
| Power-good flag over voltage tripping threshold (power bad) | VPG_OV | | 110 | | % | POWER BAD (% of FB voltage) | 4 |
| Power-good flag over voltage tripping threshold (power good) | VPG_OV | | 105 | | % | POWER GOOD (% of FB voltage) | 4 |
| PGOOD leakage current at high level output | IPG | | 200 | | nA | VPull-Up = 5V | 4 |
| PGOOD low level output voltage | VPG_LOW | | 0.1 | | V | IPull-Up = 1 mA | 4 |
| Feedback overvoltage with respect to reference voltage (rising) | VOVP | | 110 | | % | VFB/VREF rising | 4 |
| Feedback overvoltage with respect to reference voltage (falling) | VOVP | | 105 | | % | VFB/VREF falling | 4 |
| BOOT UVLO reference voltage | VBOOTUV | | 2.5 | | V | BOOT-SW falling | 4 |
| BOOT UVLO hysteresis | | | 230 | | mV | | 4 |
| Thermal shutdown threshold | TSD | | 172 | | °C | TJ rising | 4 |
| Thermal shutdown hysteresis | | | 12 | | °C | | 4 |
| Junction-to-ambient thermal resistance | θja | | 42 | | °C/W | standard board | 3 |
| Junction-to-top characterization parameter | ψjt | | 5.9 | | °C/W | | 3 |
## CAD (KiCad official)
- Symbol: `SCT2612STER`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `sct2612ster-etched.step` / `sct2612ster-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sct2612ster.step` / `sct2612ster.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [SCT datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8757136906843111424) (20 pp, sha256 `e2572ef44d882d59`, retrieved 2026-11-07, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/sct2612ster-datasheet.pdf)