← Commit history

Set visibility: public

Ray ·ab9688d41b · ·parent 0ca3c85
1 file changed +9−6
page.json+9−6
@@ -32,7 +32,7 @@         "number": "1",         "name": "BOOT",         "type": "power_in",-        "description": "Bootstrap supply for high-side power MOSFET gate driver. Connect a 0.1\u00b5F capacitor between BOOT and SW; the bootstrap cap is charged when the low-side MOSFET is on or SW is low. BOOT-SW UVLO threshold \u2248 2.36V."+        "description": "Bootstrap supply for high-side power MOSFET gate driver. Connect a 0.1µF capacitor between BOOT and SW; the bootstrap cap is charged when the low-side MOSFET is on or SW is low. BOOT-SW UVLO threshold ≈ 2.36V."       },       {         "number": "2",@@ -44,25 +44,25 @@         "number": "3",         "name": "EN",         "type": "input",-        "description": "Enable input with internal pull-up current source (~1.5\u00b5A at 1V). Pull below 1.1V to disable the converter; float or tie to VIN to enable. A VIN-to-GND resistor divider on EN sets a programmable input UVLO threshold (VEN_H \u2248 1.18V)."+        "description": "Enable input with internal pull-up current source (~1.5µA at 1V). Pull below 1.1V to disable the converter; float or tie to VIN to enable. A VIN-to-GND resistor divider on EN sets a programmable input UVLO threshold (VEN_H ≈ 1.18V)."       },       {         "number": "4",         "name": "RT/CLK",         "type": "bidirectional",-        "description": "Sets internal oscillator frequency or accepts an external clock. Resistor to GND programs Fsw from 100kHz to 1.1MHz (e.g. 200k\u03a9 \u2248 500kHz); alternatively drive with an external clock (100kHz-1.1MHz) for PLL synchronization. Reverts to resistor-programmed frequency if the external clock stops."+        "description": "Sets internal oscillator frequency or accepts an external clock. Resistor to GND programs Fsw from 100kHz to 1.1MHz (e.g. 200kΩ ≈ 500kHz); alternatively drive with an external clock (100kHz-1.1MHz) for PLL synchronization. Reverts to resistor-programmed frequency if the external clock stops."       },       {         "number": "5",         "name": "FB",         "type": "input",-        "description": "Inverting input of the transconductance error amplifier. Connect a resistor divider from VOUT to FB to GND; the loop regulates FB to VREF = 0.8V (typ, \u00b11%). Overvoltage protection trips at ~110% of VREF."+        "description": "Inverting input of the transconductance error amplifier. Connect a resistor divider from VOUT to FB to GND; the loop regulates FB to VREF = 0.8V (typ, ±1%). Overvoltage protection trips at ~110% of VREF."       },       {         "number": "6",         "name": "SS",         "type": "passive",-        "description": "Soft-start programming pin. Connect a capacitor from SS to GND; internal ~3\u00b5A source current charges it to set the output voltage ramp time."+        "description": "Soft-start programming pin. Connect a capacitor from SS to GND; internal ~3µA source current charges it to set the output voltage ramp time."       },       {         "number": "7",@@ -150,5 +150,8 @@     "docs/sct2452ster-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file